Mod. 1707
Transcript
Mod. 1707
Mod. 1707 DS 1707-002A LBT 8282 STAFFA 2GO! PER VIDEOCITOFONO VIVAVOCE IMAGO 2GO! BRACKET FOR IMAGO HANDS-FREE VIDEO DOOR PHONE ETRIER 2GO! POUR VIDÉOPHONE MAINS LIBRES IMAGO SOPORTE 2GO! PARA VIDEOINTERFONO MANOS LIBRES IMAGO HALTERUNG 2GO! FÜR VIDEOANLAGEN MIT FREISPRECHSYSTEM IMAGO Sch./Ref. 1707/82 CONFIGURAZIONE STAFFA ITALIANO CODE: codice utente Inserire un numero da 0 a 31 secondo la figura seguente e le regole seguenti: • Sull’impianto non ci devono essere appartamenti diversi con lo stesso codice utente. • Nel caso di posti interni in parallelo nello stesso appartamento, questi devono avere lo stesso codice utente. • I codici utente di una stessa dorsale devono essere consecutivi. INSTALLAZIONE • Fissare la staffa a parete con viti e tasselli, rispettando gl’ingombri laterali. 10 CODE cm 1 2 3 4 5 INT 10 1 2 3 4 5 UTENTE= 1 1 2 3 4 5 UTENTE= 2 1 2 3 4 5 UTENTE= 3 CODE ON ON 1 2 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 cm 1,55 m 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 • Collegare il cavo della linea BUS non polarizzata ai morsetti LINE IN. • Nel caso di utilizzo della funzione di chiamata al piano o di una suoneria supplementare, collegare i relativi conduttori. • Dopo aver verificato che i led gialli delle staffe sono spenti, è possibile montare sulle staffe i videocitofoni. • Rimuovere la protezione in cartone. • Agganciare il videocitofono come da figura. • Per sostituire il videocitofono, premere il gancio α e ruotare in senso orario. UTENTE= 0 1 2 3 4 5 UTENTE= 4 UTENTE= 8 UTENTE= 12 UTENTE= 16 UTENTE= 20 UTENTE= 24 UTENTE= 28 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 UTENTE= 5 UTENTE= 9 UTENTE= 13 UTENTE= 17 UTENTE= 21 UTENTE= 25 UTENTE= 29 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 UTENTE= 6 UTENTE= 10 UTENTE= 14 UTENTE= 18 UTENTE= 22 UTENTE= 26 UTENTE= 30 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 UTENTE= 7 UTENTE= 11 UTENTE= 15 UTENTE= 19 UTENTE= 23 UTENTE= 27 UTENTE= 31 INT: Codice dell’interno dell’appartamento Impostare un numero da 0 a 3 secondo la figura e le regole seguenti: • Nel caso di un solo posto interno presente nell’appartamento, il codice dell’interno deve essere impostato a 0. • Negli appartamenti è possibile collegare fino a 4 posti interno in parallelo tutti con lo stesso codice utente, ma con codici interni differenti. INT INT ON ON 1 2 1 2 3 4 5 1 2 INTERNO= 0 1 2 INTERNO= 1 1 2 INTERNO= 2 1 2 INTERNO= 3 Il codice dell’interno serve ad identificare i singoli posti interni dello stesso utente. Questo permette di effettuare chiamate intercomunicanti indirizzate al singolo interno nell’ambito dello stesso appartamento. Nel caso di chiamate intercomunicanti ad appartamenti differenti, nel caso di chiamate provenienti da posti esterni e nel caso di chiamata al piano, squillano sempre tutti i posti interni dell’utente. Occorre tenere presente inoltre, le seguenti considerazioni: • Gli interni 0 e 1, alla ricezione della chiamata, squillano subito; gli interni 2 e 3 squillano immediatamente dopo. • Se la chiamata proviene da un posto esterno videocitofonico, l’interno 0 abilita l’accensione del monitore. Gli altri posti interni possono comunque premere il pulsante per accendere il loro videocitofono spegnendo l’altro (funzione “palleggiamento video”). α 2 CODE DS1707-002A DS1707-002A 3 FUNZIONAMENTO VALORI DI DEFAULT 1 Tutte le staffe escono di fabbrica configurate nel seguente modo:: INT CODE ON ON 1 2 1 2 3 4 5 CODE = 31 INT =0 Z = ON ON Z: selettore terminazione LINEA 2 In questo modo, per il corretto funzionamento dell’impianti, è sempre necessario porre attenzione ai dip switch per impostarli al valore corretto. 3 4 IMPOSTAZIONE DELLA TERMINAZIONE DELLA LINEA 7 5 6 Sulla staffa è presente un interruttore che permette di inserire la terminazione della linea. È necessario attivare la terminazione in tutti i dispositivi cablati alla fine di una linea che non riparte con un’altra tratta dallo stesso dispositivo (fine linea). Terminazione ON Terminazione ON 10 82 /5 (IN 1 /O PA LI UT) TEN NE TE (D D ER LI ) NE ON OFF PULSANTI AUSILIARI: utilizzabili per funzioni speciali dipendenti dall’impianto. 2 JOYSTICK: per regolare i parametri video. 3 PULSANTE PER AUTOINSERZIONE/PALLEGGIAMENTO VIDEO. 4 PULSANTE APRIPORTA: si illumina in verde per il periodo di accensione del videocitofono. Si illumina in rosso per segnalare la porta aperta o lampeggia in rosso per segnalare la funzione di apriporta automatico. 5 PULSANTE FONIA: si illumina in verde per il periodo di accensione del videocitofono. Premendo il tasto si attiva la fonia, il pulsante si illumina in arancione. Non è necessario mantenere il tasto premuto durante la conversazione (funzione “MANI LIBERE”). La conversazione fonica viene interrotta premendo il pulsante una seconda volta, oppure al momento dello spegnimento del videocitofono. 6 COMANDO REGOLAZIONE VOLUME DI CHIAMATA/MUTE. 7 SEGNALAZIONE ESCLUSIONE DI CHIAMATA: La posizione di Mute è evidenziata dalla fuoriuscita dal lato sinistro del videocitofono di una bandierina di segnalazione. DESCRIZIONE DEI MORSETTI LINE IN LINE OUT CP S+; S- LIN E4 LIN E3 LIN E2 LIN E1 LIN E0 1 2 3 4 Terminazione OFF Terminazione ON 1 Coppia di morsetti da collegare alla linea non polarizzata Coppia di morsetti da utilizzare per il collegamento dell’uscita della linea non polarizzata Coppia di morsetti da utilizzare per il collegamento di un pulsante di chiamata al piano Coppia di morsetti da utilizzare per il collegamento di una suoneria supplementare Terminazione ON 4 DS1707-002A DS1707-002A 5 RICEZIONE DELLE CHIAMATE E FUNZIONE “PALLEGGIAMENTO VIDEO” GESTIONE SUONERIA SUPPLEMENTARE Alla ricezione di una chiamata, il posto interno dell’utente squilla con la melodia impostata secondo le seguenti tempistiche: Il posto interno è dotato di una coppia di morsetti (S-, S+) per il collegamento di una soneria supplementare o di un relè. Tale soneria viene pilotata contemporaneamente alla generazione di qualsiasi squillo di chiamata. PROVENIENZA CHIAMATA TEMPISTICHE DURATA TOTALE DELLO SQUILLO 3s ON 3s Chiamata da posto esterno secondario 0,4s ON 0,2s OFF per 5 volte 2,8s Chiamata intercomunicante 0,5s ON 0,5s OFF per 3 volte 2,5s 3s ON 3s Chiamata da posto esterno principale Chiamata al piano RIEPILOGO FUNZIONE PULSANTI / / / La seguente tabella riepiloga le funzioni dei tasti in relazione allo stato del posto interno: STATO Se il posto interno è a riposo, è possibile fare autoinserzione sulla postazione “Master” tramite la pressione del pulsante . Premere il pulsante per attivare la comunicazione audio con il posto esterno “Master”; l’utente può aprire la porta in qualunque momento. FUNZIONE APRIPORTA AUTOMATICO La prestazione è attivabile/disattivabile per mezzo del pulsante dedicato . L’attivazione della funzione è segnalata dall’accensione intermittente del tasto apriporta in colore rosso. Attivando questa funzione, ad ogni chiamata giunta da una pulsantiera, verrà automaticamente comandata l’elettroserratura. Se l’utente ha più interni in parallelo, inserire la prestazione su uno solo apparecchio. Fonia OFF in seguito a chiamata ricevuta Chiamata ricevuta e fonia ON Riposo e fonia ON autoinserzione su principale palleggiamento video === Se programmato chiamata intercomunicante (3) o chiamata al centralino (1) Attivazione segreteria video (1) Attivazione luci scale (2) Attivazione luci scale (2) Se programmato chiamata intercomunicante (3) Attivazione / disattivazione apriporta automatico === === Se programmato chiamata intercomunicante (3) === === === Se programmato chiamata intercomunicante (3) PULSANTE Dalla ricezione della chiamata videocitofonico o citofonica, è sempre possibile pilotare l’attivazione dell’elettroserratura del posto esterno anche senza attivare la fonia. Se nell’appartamento ci sono più posti interni in parallelo, gli interni 0 e 1 squilleranno subito; immediatamente dopo, squilleranno gl’interni 2 e 3. L’interno dell’utente 0 pilota anche l’accensione del videocitofono se la chiamata proviene da un posto esterno videocitofonico. In tal caso, durante tutto il tempo di attesa attivazione fonia (60s dalla chiamata), gli altri interni possono accendere il loro videocitofono tramite la pressione del pulsante di autoinserzione (funzione “palleggiamento video”) fino all’attivazione della fonia di uno degl’interni. Dopo l’attivazione della fonia, l’immagine sarà presente sul solo interno che ha la fonia attiva. L’immagine della telecamera sarà quindi sempre presente su un solo videocitofono per volta. FUNZIONE AUTOINSERZIONE Riposo e fonia OFF (1) (2) (3) Ove previsto. Tramite decodifica Sch. 1082/80. Oppure attivazione 2^ elettroserratura tramite decodifica Sch. 1082/80. FUNZIONE PORTA APERTA DEL POSTO ESTERNO “MASTER” Se sul posto esterno “Master” si connette un sensore di porta aperta sui morsetti SP/GND, i posti interni possono monitorare lo stato fisico di tale porta. Quando la porta è aperta, il pulsante si illumina in rosso. PROGRAMMAZIONI FUNZIONI SUPPLEMENTARI Dopo aver verificato il funzionamento base del sistema, solo se sono richieste le seguenti funzioni, è necessario effettuare le opportune operazioni di programmazione: INOLTRO DELLE CHIAMATE INTERCOMUNICANTI Dopo aver programmato un pulsante ( / / / ) per la funzione intercomunicante, (vedi paragrafo relativo alla programmazione funzioni supplementari ), premere in successione il tasto e il tasto di chiamata ( / / / ). Possono verificarsi i seguenti casi in relazione allo stato del posto interno chiamato: • Posto interno libero: il posto interno chiamante emette un tono di conferma (2 beep) e il posto interno chiamato squilla. All’attivazione della fonia del chiamato, si entra in comunicazione. • Posto interno occupato: il posto interno chiamante emette un tono di dissuasione (4 beep veloci); premere il tasto e riprovare in seguito. FUNZIONE INTERCOMUNICANTE SU POSTO INTERNO Nel sistema 2GO! è possibile programmare i pulsanti / / / dei posti interni per la funzione di chiamata intercomunicante. Un pulsante può essere programmato per chiamare un altro utente dell’impianto oppure per chiamare un posto interno in parallelo. Nel primo caso, squillano tutti i posti interni dell’utente chiamato; nel secondo caso, squilla solo il posto interno specificato in programmazione. FUNZIONE CHIAMATA AL PIANO Il posto interno è dotato di una coppia di morsetti (CP) per il collegamento del pulsante di chiamata al piano. Alla pressione del pulsante, il posto interno emette uno squillo della durata di 3s secondo la melodia impostata. Se l’utente ha più posti interni in parallelo, connettere tale pulsante solo sull’interno 0. Gl’interni 0 e 1 squilleranno subito; gl’interni 2 e 3 squilleranno immediatamente dopo. 6 DS1707-002A DS1707-002A 7 FUNZIONE INTERCOMUNICANTE FRA UTENTI DIVERSI 1. Recarsi presso il posto interno da programmare come chiamante (posto interno A). 2. Tenendo premuto il tasto , premere il tasto . Il posto interno A emette un tono ad indicare l’ingresso in programmazione. Il tasto inizia a lampeggiare in rosso. A FUNZIONE INTERCOMUNICANTE NELLO STESSO APPARTAMENTO La procedura di programmazione è la medesima descritta precedentemente per programmare un pulsante a svolgere la funzione di intercomunicante fra utenti diversi, ad eccezione che è obbligatorio ultimare la programmazione premendo il tasto apriporta del videocitofono B che vogliamo chiamare (vedi passo 4 del paragrafo precedente), non potendo chiamare il solo interno desiderato dalla pulsantiera. MELODIA DI CHIAMATA VIDEOCITOFONICA Nei videocitofoni installati in impianti 2GO!, si può scegliere fra 5 melodie di chiamata. La scelta delle melodie può essere effettuata anche dall’utente finale con queste semplici sequenze: , premere e rilasciare il pulsante . Il posto interno emette uno squillo 1. Tenendo premuto il pulsante con una melodia. , ripremere il pulsante per cambiare melodia. 2. Sempre mantenendo premuto il pulsante 3. Quando si trova la melodia desiderata, rilasciare il pulsante . La melodia è programmata. BEEP 3. Premere il tasto da programmare; il posto interno emette un tono di conferma. Il tasto può essere: / / / . A BEEP 4. Recarsi presso l’utente che quel pulsante dovrà chiamare (utente B) e premere il pulsante . Entrambi i posti interni emettono un “beep” di avvenuta programmazione. In alternativa, recarsi presso una postazione di chiamata e premere il pulsante di chiamata dell’utente B; il posto interno in programmazione (A) emette un “beep” di avvenuta programmazione. In concomitanza di questa operazione, i posti interni dell’utente B squillano. Ignorare questa chiamata. MELODIA DI CHIAMATA AL PIANO O INTERCOM Nei videocitofoni del sistema 2GO!, si può scegliere fra 5 melodie di chiamata al piano. La scelta delle melodie può essere effettuata anche dall’utente finale con queste semplici sequenze: 1. Tenendo premuto il pulsante , premere e rilasciare il pulsante . Il posto interno emette uno squillo con una melodia. 2. Sempre mantenendo premuto il pulsante , ripremere il pulsante per cambiare melodia. 3. Quando si trova la melodia desiderata, rilasciare il pulsante . La melodia è programmata. B BEEP UTENTE B 5. Ripremere il pulsante del posto interno A che emette un beep di uscita dalla programmazione. Il tasto si spegne. 6. Verificare la funzione programmata: premere il pulsante del posto interno A e quindi premere il pulsante programmato. Verificare che squillino tutti i posti interni dell’utente B; premere il pulsante di un videocitofono B e verificare che possa comunicare con il posto interno A. 7. Se si vuole eseguire anche la chiamata inversa, è necessario programmare il videocitofono B per chiamare A. § Iperdono pulsanti / / / anche se vengono programmati con la funzione intercomunicante, non le loro funzioni base rispettivamente di autoinserzione/palleggiamento video, attivazione CANCELLAZIONE DEI DATI DI PROGRAMMAZIONE (ripristino condizioni iniziali) Per cancellare tutti i dati di programmazione opzionali, eseguire le seguenti operazioni: 1. Tenendo premuto il tasto , premere il tasto . Il posto videocitofono emette due beep per segnalare l’ingresso in programmazione. Il tasto inizia a lampeggiare in rosso. 2. Premere contemporaneamente i tasti e , e tenerli premuti per 3 secondi fino all’emissione di un tono di conferma dell’avvenuta cancellazione. 3. Ripremere il pulsante del posto interno. Il videocitofono emette un tono di conferma dell’uscita dalla programmazione; Il tasto si spegne. segreteria video e abilitazione apriporta automatico, in quanto queste funzioni sono inseribili solo con fonia disattiva. 8 DS1707-002A DS1707-002A 9 BRACKET CONFIGURATION ENGLISH CODE: user code. Set a number from 0 to 31 as shown in the figure according to the following rules: • No two apartments in the system must have the same user code. • Indoor stations in parallel in the same apartment must have the same user code. • User codes be consecutive in the same spine must. INSTALLATION • Fasten the bracket to the wall with screws and bolts respecting the side dimensions. 10 CODE cm 1 2 3 4 5 INT 10 ON 1 2 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 cm 1,55 m 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 Connect the non-polarised Bus line wire to the LINE IN terminals. To use the floor call or supplementary ringer function, connect the respective wires. Fit the video door phones on the brackets after checking that the bracket yellow LEDs are off. Remove the cardboard protection. Fasten the video door phone as shown in the figure. To replace the video door phone, press the hook and turn it clockwise. 1 2 3 4 5 USER= 1 1 2 3 4 5 USER= 2 1 2 3 4 5 USER= 3 CODE ON 1 2 3 4 5 • • • • • • USER= 0 1 2 3 4 5 USER= 4 USER= 8 USER= 12 USER= 16 USER= 20 USER= 24 USER= 28 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 USER= 5 1 2 3 4 5 USER= 9 1 2 3 4 5 USER= 13 USER= 17 USER= 21 USER= 25 USER= 29 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 USER= 6 USER= 10 USER= 14 USER= 18 USER= 22 USER= 26 USER= 30 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 USER= 7 USER= 11 USER= 15 USER= 19 USER= 23 USER= 27 USER= 31 INT: apartment station code. Set a number from 0 to 3 as shown in the figure according to the following rules: • The indoor station code must be 0 if there is one only station in the apartment. • Up to 4 apartment stations can be connected in parallel using the same user code and different indoor station codes. INT INT ON ON 1 2 1 2 3 4 5 1 2 INDOOR STATION= 0 1 2 INDOOR STATION=1 1 2 INDOOR STATION= 2 1 2 INDOOR STATION= 3 The indoor station code is used to identify the single stations of the same user. This means that intercom calls can be address to the single user in the same apartment. All the users indoor stations will ring at the same time in the event of intercom calls to different apartments, door unit calls and floor calls. Consider the following: • Indoor stations 0 and 1 will ring immediately when the call is received. Stations 2 and 3 will ring immediately after. • Indoor station 0 will enable monitor switch-on if the call is from a video door unit. The button can be pressed on any other indoor station of the same user to switch on the other video door phone (“video switching” function). α 10 CODE DS1707-002A DS1707-002A 11 OPERATION DEFAULT SETTINGS 1 Default indoor station settings are: INT CODE ON ON 1 2 1 2 3 4 5 CODE = 31 INT =0 Z = ON ON Z: line termination 2 The dip switches must always be arranged in the correct setting for correct operation of the system in this case. 3 4 LINE TERMINAL SETTINGS 7 5 6 A switch for fitting a line terminal is present on indoor stations bracket. Activate the terminal for devices wired at the end of a line from which another section does not start from the device terminals (end of line). Termination ON AUXILIARY BUTTONS: these can be used for specific functions according to the system. 2 JOYSTICK: this is used to adjust the video parameters. 3 AUTO-ON/VIDEO SWITCHING BUTTON. 4 DOOR OPENER BUTTON: This LED turns green when the video door phone is on. It turns red to indicate that the door is open and blinks red to indicate that the automatic door opening function is on. 5 AUDIO BUTTON: This lights up green when the video door phone is on. The button will turn amber when the audio button is pressed. The button does not need to be held pressed during the conversation (“FREE-HANDS” function). The audio conversation is cut off when either the button is pressed again or when the video door phone is switched off. 6 CALL VOLUME/MUTE CONTROL. 7 MUTE INDICATOR: A tab protrudes from the left-hand side of the video door phone when the volume is muted. Termination ON 10 82 /5 (IN 1 /O PA LI UT) TEN NE TE (D D ER LI ) NE Termination OFF Termination ON 1 ON OFF DESCRIPTION OF TERMINALS LIN E4 LIN E3 LIN E2 LIN E1 LIN E0 1 2 3 4 LINE IN LINE OUT CP S+; S- Terminal pair to be connected to the non-polarised line Terminal pair to be used to connect the output of the non-polarised line Terminal pair to be used for connect a floor call button Terminal pair to be used for connecting a supplementary ringer Termination ON 12 DS1707-002A DS1707-002A 13 CALL RECEPTION AND VIDEO SHIFTING FUNCTION SUPPLEMENTARY RINGER MANAGEMENT The user’s indoor station will ring with the programmed tone when a call is received for the following times: The apartment station is equipped with a pair of terminals (S-, S+) for connecting a supplementary ringer or a relay. This ringer is controlled when any call tone is generated. CALL ORIGIN TIME TOTAL DURATION OF THE TONE Call from main door unit 3s ON 3s Call from secondary door unit 0.4s ON 0.2s OFF for 5 times 2,8s Intercom call 0.5s ON 0.5s OFF for 3 times 2,5s 3s ON 3s Floor calls BUTTON FUNCTION OVERVIEW / / / The following table shows an overview of the buttons in relation to the apartment station state: STATE Stand-by and audio OFF Audio OFF following received call Call received and audio ON Stand-by and audio ON Master auto-on Video switching === If programmed, intercom call (3) or call to switchboard (1) Video answering service on (1) Staircase lights on (2) Staircase lights on (2) If intercom call (3) is programmed Automatic door opener on/off === === If intercom call (3) is programmed === === === If intercom call (3) is programmed BUTTON The electrical lock can be operated from the door unit also without activating the audio when a video door unit or door unit call is received. Apartment stations 0 and 1 will ring immediately if there are several stations in the apartment. Apartment stations 2 and 3 will ring immediately after this. The user can switch the monitor on from station 0 if the call was made from a video door phone door unit. In this case, during the audio waiting time (60s from the call before the handset is picked up), the video door phones of the other extensions can be switched on by pressing the auto-on button (video switching function) before activating the audio of one of the extensions is turned on. After activating the audio, the image will be shown only on the extension from where the audio function was activated. The picture will therefore be present on only one video door phone at a time. (1) (2) (3) AUTO-ON FUNCTION Press the button to activate the auto-on function on “Master” station if the apartment station is in standby. Press the button to establish an audio communication with the “Master” door unit. The user can open the door at any time. Where fitted. By means of decoder Ref. 1082/80. Or second lock operation by means of decoder Ref. 1082/80. “MASTER” DOOR PANEL DOOR OPEN FUNCTION The apartment stations can monitor with physical state of the Master door by connecting a sensor to the SP/GND terminals. The button will turn red when the door is open. AUTOMATIC DOOR OPENER FUNCTION The function can be switched on and off by means of the specific button . The door opener button will blink red to indicate that the function is on. When the function is on, the electrical lock will be automatically released when a call is received from the door panel. Program this function on one of the devices only if there are several extensions in parallel. SUPPLEMENTARY FUNCTION PROGRAMMING FORWARDING INTERCOM CALLS INDOOR STATION INTERCOM FUNCTION The buttons / / / can be programmed to manage the intercom call function in 2GO! systems. One button can be programmed to call another user in the system or to call an indoor station in parallel. All indoor stations of the called user will ring in the first case. Only the specifically programmed indoor station will ring in the second case. After having programmed a button ( / / / ) for intercom calls (see paragraph on how to program supplementary functions), press the button and the call button ( / / / ) in sequence. The following cases can occur according to the state of the called apartment station: • Apartment station in stand-by: the calling apartment stations will output a confirmation tone (two beeps) and the called apartment station will ring. A communication is established when the caller’s audio is activated. • Apartment station busy: the calling apartment station will output a deterrent tone (four beeps in rapid sequence); press the button and try again later. The following programming operations are needed after testing the basic operation of the system only if the following functions are required. FLOOR CALL BUTTON The apartment station is equipped with a pair or terminals (CP) for connecting the floor call button. The apartment station will ring with the set tone for 3s when the button is pressed. Connect this button to extension 0 only if there are extensions in parallel. Extensions 0 and 1 will ring immediately. Apartments 2 and 3 will ring immediately after. 14 DS1707-002A DS1707-002A 15 INTERCOM FUNCTION BETWEEN VARIOUS USERS 1. Go to the indoor station to be programmed as caller (indoor station A). 2. Holding button pressed, press button . The indoor station A outputs a tone to indicate that will start blinking red. programming mode is in progress. Button A INTERCOM FUNCTION IN THE SAME APARTMENT The programming procedure is the same as that described above for programming a button for the intercom function with the exception that programming must be ended by pressing the door opener button of the video door phone B to be called (see step 4 in the paragraph above) because the only required extension cannot be called from the panel. DOOR PHONE CALL TONE Five tones can be selected on 2GO! system indoor stations. The tones can be programmed also by the end user by following the simple sequence below: pressed. Press and release the button. The indoor station will play 1. Hold the door opener button a tone. pressed and press the button again to change the tone. 2. Hold the door opener button 3. Release the door opener button when you have chosen the tone you want. The tone is now programmed. BEEP 3. Press the button to be programmed. The indoor station will output a confirmation tone. The button can be / / / . A BEEP 4. Go to the user that the button will call (user B) and press the door opener button. The indoor stations will be beep to indicate that they have been programmed. Alternatively, go to a calling station and press the calling button of user B. The indoor station being programming (A) will beep to indicate that it has been programmed. The indoor stations of user B will ring when this occurs. Ignore this call. B BEEP FLOOR CALL TONE Five floor call tones can be selected on 2GO! system indoor stations. The tones can be programmed also by the end user by following the simple sequence below: 1. Hold the door opener button pressed. Press and release the button . The indoor station will play a tone. 2. Hold the door opener button pressed and press the button again to change the tone. 3. Release the door opener button when you have chosen the tone you want. The tone is now programmed. USER B 5. Press button on apartment station A again. It will beep to indicate exit from programming mode. Button will go out. 6. Check the programmed function: press button of apartment station A and then press the programmed button. Check that all the apartment stations of user B rings. Press button on a video door phone B and check that communication can be established with apartment station A. 7. You will need to program indoor station B to call A to make the opposite call possible. § Buttons / / / also when used for programming intercom functions keep their basic functions (auto-on/video switching, video mail, automatic door opening function) because the functions can only PROGRAMMING DATA DELETION (restore default settings) Proceed as follows to delete all optional programming data: 1. Holding button pressed, press button . The video door phone will beep twice to indicate that it is in programming mode. Button will start blinking red. 2. Press and at the same time for 3 seconds until you hear the deletion tone. 3. Press the apartment station button . The video door phone will beep when you exit programming. Button will go out. 16 DS1707-002A be selected when the audio is off. DS1707-002A 17 CONFIGURATION DES ETRIERS FRANÇAIS INSTALLATION • Fixer l’étrier au mur à l’aide de vis et de chevilles,en respectant les encombrements latéraux. 10 CODE: code utilisateur. Programmer un numéro compris entre 0 et 31, selon la figure et les règles suivantes: • Il ne doit pas y avoir d’appartements différents avec le même code utilisateur; • En présence de postes internes en parallèle dans le même appartement, ceux-ci doivent avoir le même code utilisateur; • Les codes utilisateur d’une même dorsale doivent être consécutifs. CODE cm 1 2 3 4 5 INT 10 1 2 3 4 5 UTILIS.= 1 1 2 3 4 5 UTILIS.= 2 1 2 3 4 5 UTILIS.= 3 CODE ON ON 1 2 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 cm 1,55 m 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 • Brancher le câble de la ligne Bus non polarisée aux bornes LINE IN. • En cas d’utilisation de la fonction appel à l’étage ou d’une sonnerie supplémentaire, brancher les conducteurs correspondants. • Après avoir vérifié que les diodes jaunes des étriers sont éteintes, il est possible d’installer les vidéophones sur lesdits étriers. • Retirer la protection en carton • Accrocher le vidéophone, comme illustré dans la figure. • Pour remplacer le vidéophone, appuyer sur le crochet et tourner dans le sens des aiguilles d’une montre. UTILIS.= 0 1 2 3 4 5 1 2 3 4 5 UTILIS.= 4 UTILIS.= 8 UTILIS.= 12 UTILIS.= 16 UTILIS.= 20 UTILIS.= 24 UTILIS.= 28 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 UTILIS.= 5 UTILIS.= 9 UTILIS.= 13 UTILIS.= 17 UTILIS.= 21 UTILIS.= 25 UTILIS.= 29 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 UTILIS.= 6 UTILIS.= 10 UTILIS.= 14 UTILIS.= 18 UTILIS.= 22 UTILIS.= 26 UTILIS.= 30 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 UTILIS.= 7 UTILIS.= 11 UTILIS.= 15 UTILIS.= 19 UTILIS.= 23 UTILIS.= 27 UTILIS.= 31 INT: code du poste interne de l’appartement. Programmer un numéro compris entre 0 et 3, selon la figure et les règles suivantes: • Si un seul poste interne est présent dans l’appartement, le code du poste interne doit être égal à 0. • Dans les appartements, il est possible de brancher jusqu’à un maximum de 4 postes internes en parallèle, ayant tous le même code utilisateur, mais avec des codes internes différents. INT INT ON ON 1 2 1 2 3 4 5 1 2 INTERNE= 0 1 2 INTERNE= 1 1 2 INTERNE= 2 1 2 INTERNE= 3 Le code du poste interne sert à ‘identifier les différents postes internes d’un même utilisateur. Cela permet d’effectuer des appels intercom adressés à un poste interne donné, à l’intérieur du même appartement. En cas d’appels intercom vers des appartements différents ou d’appels en provenance de postes externes et d’appels à l’étage, tous les postes internes de l’utilisateur sonnent. Il est en outre nécessaire de rappeler ce qui suit: • Dès la réception d’un appel, les postes internes 0 et 1 sonnent, immédiatement suivis des postes internes 2 et 3. • Si l’appel provient d’un poste externe de vidéophone, le poste interne 0 habilite l’allumage de l’écran. Les autres postes internes du même utilisateur peuvent toujours appuyer sur la touche pour allumer leur vidéophone, en éteignant l’autre (fonction “renvoi vidéo”). α 18 CODE DS1707-002A DS1707-002A 19 FONCTIONNEMENT VALEURS IMPLICITES 1 Tous les postes internes sont configurés en usine comme suit: INT CODE ON ON 1 2 1 2 3 4 5 CODE = 31 INT =0 Z = ON ON Z: terminaison ligne 2 Ainsi, pour assurer un fonctionnement régulier, il est toujours nécessaire de veiller à programmer correctement les commutateurs. 3 4 CONFIGURATION DES TERMINAISONS DE LIGNE 7 5 6 Les etrieres des internes comportent un interrupteur permettant d’insérer la terminaison de ligne. Il est nécessaire d’activer la terminaison dans tous les dispositifs câblés à la fin d’une ligne qui ne repart pas avec un autre segment des mêmes bornes du dispositif lui-même (fin de ligne). Terminaison ON Terminaison ON 10 82 /5 (IN 1 /O PA LI UT) TEN NE TE (D D ER LI ) NE ON OFF BOUTONS AUXILIAIRES: utilisables pour des fonctions spéciales, qui varient en fonction de l’installation. 2 JOYSTICK: pour régler les paramètres vidéo. 3 BOUTON D’INSERTION AUTOMATIQUE/RENVOI VIDÉO. 4 BOUTON OUVRE-PORTE: il s’allume en vert lorsque le vidéophone est sous tension. Il passe au rouge pour signaler la porte ouverte ou bien il clignote en rouge pour signaler la fonction ouvre-porte automatique. 5 BOUTON PHONIE: il s’allume en vert lorsque le vidéophone est sous tension. Appuyer pour activer la phonie ; la bouton s’allume en orange. Il n’est pas nécessaire de maintenir la touche appuyée pendant la conversation (fonction “MAINS LIBRES”). La conversation phonique s’interrompt en appuyant de nouveau sur le bouton ou lors de la mise hors tension du vidéophone. 6 COMMANDE DE REGLAGE DU VOLUME D’APPEL/MUTE. 7 SIGNALISATION D’EXCLUSION D’APPEL: La position Mute est mise en évidence par l’apparition, sur le côté gauche du vidéophone, d’un petit drapeau de signalisation. DESCRIPTION DES BORNES LINE IN LINE OUT CP S+ ; S- LIN E4 LIN E3 LIN E2 LIN E1 LIN E0 1 2 3 4 Terminaison OFF Terminaison ON 1 Paire de bornes à connecter à la ligne non polarisée Paire de bornes à utiliser pour le raccordement de la sortie de la ligne non polarisée Paire de bornes à utiliser pour le raccordement d’un bouton d’appel à l’étage Paire de bornes à utiliser pour le raccordement d’une sonnerie supplémentaire Terminaison ON 20 DS1707-002A DS1707-002A 21 RECEPTION DES APPELS EN FONCTION ‘RENVOI VIDEO’ GESTION D’UNE SONNERIE SUPPLÉMENTAIRE Dès réception d’un appel, le poste interne de l’utilisateur émet la tonalité programmée, selon les modalités suivantes: Le poste interne est doté d’une paire de bornes (S-, S+) pour le raccordement d’une sonnerie supplémentaire ou d’un relais. Cette sonnerie est pilotée simultanément à l’émission de n’importe quelle sonnerie d’appel. PROVENANCE DE L’APPEL TEMPS Appel depuis un poste externe principal DURÉE TOTALE DE LA TONALITÉ 3s ON 3s Appel depuis un poste externe secondaire 0,4s ON 0,2s OFF à 5 reprises 2,8s Appel intercom 0,5s ON 0,5s OFF à 3 reprises 2,5s Appel à l’étage 3s ON 3s RÉCAPITULATIF DES FONCTIONS DES BOUTONS / / / Le tableau suivant récapitule les fonctions des touches suivant l’état du poste interne: ETAT Repos et phonie OFF Phonie OFF suite à la réception d’un appel Appel reçu et phonie ON Repos et phonie ON Insertion automatique sur poste principal renvoi vidéo === Si appel intercom (3) ou appel vers centrale (1) programmés Activation répondeur vidéo (1) Activation éclairage d’escalier (2) Activation éclairage d’escalier (2) Si appel intercom programmé (3) Activation / désactivation ouvreporte automatique === === Si appel intercom programmé (3) === === === Si appel intercom programmé (3) BOUTON A partir de la réception d’un appel de vidéophone/interphone, il est toujours possible de piloter l’activation de la serrure électrique du poste externe, sans qu’il soit nécessaire d’activer la phonie. Si l’appartement comporte plusieurs postes internes en parallèle, les postes 0 et 1 sonneront immédiatement, suivis juste après par les postes 2 et 3. Le poste de l’utilisateur 0 pilote aussi l’allumage du vidéophone lorsque l’appel provient d’un poste externe à vidéophone. Dans ce cas, pendant toute la durée d’attente d’activation de la phonie (60 s depuis l’appel), les autres postes internes peuvent allumer leur vidéophone en appuyant sur le bouton d’insertion automatique (fonction “renvoi vidéo”), jusqu’à l’activation de la phonie de l’un des postes. Une fois la phonie activée, l’image sera uniquement affichée sur le poste interne avec la phonie active. L’image de la caméra sera donc toujours présente sur un seul vidéophone à la fois. FONCTION INSERTION AUTOMATIQUE Si le poste externe est au repos, il est possible d’activer l’insertion automatique sur le poste “Master”, en appuyant sur le bouton . Appuyer sur le bouton pour activer la communication audio avec le poste externe “Master”; l’utilisateur peut ouvrir la porte à tout moment. FONCTION OUVRE-PORTE AUTOMATIQUE Cette fonction peut être activée/désactivée en agissant sur le bouton prévu à cet effet. L’activation de la fonction est signalée par l’allumage intermittent de la touche ouvre-porte en rouge. Lorsque cette fonction est activée, tout appel en provenance d’un clavier entraînera automatiquement la serrure électrique. Si l’utilisateur comporte plusieurs postes en parallèle, activer la fonction sur un seul poste. (1) (2) (3) Si prévu. Par décodeur Réf. 1082/80. Ou bien activation 2ème serrure électrique par décodeur Réf. 1082/80. FONCTION PORTE OUVERTE DU POSTE EXTERNE “MASTER” Si un capteur de porte ouverte est connecté sur les bornes SP/GND du poste externe ‘Master’, les postes internes peuvent surveiller l’état physique de cette porte. Lorsque la porte est ouverte, le bouton s’allume en rouge. PROGRAMMATION DES FONCTIONS SUPPLÉMENTAIRES Après avoir vérifié le fonctionnement de base du système, il est nécessaire d’exécuter les opérations de programmation si les prestations suivantes sont requise. ACHEMINEMENT DES APPELS INTERCOM Après avoir programmé un bouton ( / / / ) pour la fonction intercom (voir paragraphe concernant la programmation des fonctions supplémentaires), appuyer dans l’ordre la touche et la touche d’appel ( / / / ). Les cas suivants peuvent se présenter, en fonction de l’état du poste interne appelé: • Poste interne libre: le poste interne appelant émet une tonalité de validation (2 bips sonores) et le poste interne appelé se met à sonner. La communication est établie à l’activation de la phonie du poste appelé. • Poste interne occupé: le poste interne appelant émet une tonalité de dissuasion (4 bips rapides); appuyer sur la touche et retenter plus tard. FONCTION INTERCOM SUR POSTE INTERNE Dans le système 2GO!, il est possible de programmer les touches / / / des postes internes pour la fonction appel intercom. Une touche peut être programmée pour appeler un autre utilisateur de l’installation ou pour appeler un poste interne en parallèle. Dans le premier cas, tous les postes internes de l’utilisateur appelé sonnent; dans le deuxième cas, seul le poste interne spécifié lors de la programmation se met à sonner. FONCTION APPEL À L’ÉTAGE Le poste interne est doté d’une paire de bornes (CP) pour le branchement de la touche d’appel à l’étage. Lors de l’actionnement de la touche, le poste interne émet la tonalité programmée durant 3 secondes. Si l’utilisateur comporte plusieurs postes internes en parallèle, brancher ce bouton uniquement sur le poste 0. Les postes 0 et 1 sonneront immédiatement, suivis juste après par les postes 2 e 3. 22 DS1707-002A DS1707-002A 23 FONCTION INTERCOM ENTRE UTILISATEURS 1. Se rendre auprès du poste interne à programmer en tant que poste appelant (poste interne A). 2. Tout en actionnant la touche , appuyer sur la touche . Le poste interne A émet une tonalité pour se met à clignoter. indiquer l’accès en mode programmation. La touche A FONCTION INTERCOM DANS LE MÊME APPARTEMENT La procédure de programmation est la même que celle précédemment décrite pour programmer un bouton afin qu’il assure la fonction intercom entre plusieurs utilisateurs, à une différence près: il faut obligatoirement achever la programmation en appuyant sur la touche ouvre-porte du vidéophone B à appeler (voir étape 4 du paragraphe précédent), compte tenu de l’impossibilité d’appeler le seul poste désiré depuis le clavier. TONALITE D’APPEL D’INTERPHONE Dans les postes internes du système 2GO!, il est possible de choisir parmi 5 tonalités d’appel. Le choix des tonalités peut être effectué aussi par l’utilisateur final. Il suffit de procéder comme suit: appuyée, appuyer et relâcher la touche . Le poste 1. Tout en maintenant la touche ouvre-porte interne émet une sonnerie avec une tonalité. appuyée, appuyer de nouveau sur la touche pour 2. En maintenant toujours la touche ouvre-porte changer de tonalité. 3. Après avoir trouvé la tonalité désirée, relâcher la touche ouvre-porte . La tonalité est programmée. BEEP 3. Appuyer sur la touche à programmer. Le poste interne émet une tonalité de validation. La touche peut être / / / . A BEEP 4. Se rendre auprès de l’utilisateur qui devra être appelé par cette touche (utilisateur B) et appuyer sur la touche ouvre-porte . Les postes internes émettent un bip sonore pour indiquer que la programmation a bien eu lieu. En alternative, se rendre auprès d’un poste d’appel et appuyer sur la touche d’appel de l’utilisateur B; le poste interne en programmation (A) émet un bip sonore pour indiquer que la programmation a bien eu lieu. En même temps, les postes internes de l’utilisateur B sonnent. Ignorer cet appel. B BEEP UTILIS. B 5. Appuyer de nouveau sur le bouton du poste interne A, qui émet un bip sonore de sortie de la programmation. La touche s’éteint. 6. Vérifier la fonction programmée: appuyer sur le bouton du poste interne A, puis appuyer sur le bouton programmé. Vérifier que tous les postes internes de l’utilisateur B sonnent; appuyer sur le bouton d’un vidéophone B et vérifier s’il peut communiquer avec le poste interne A. 7. Si l’on souhaite programmer aussi l’appel inverse, il est nécessaire de configurer le poste interne B pour l’appel vers A. § leurs Même s’ils sont programmés avec la fonction intercom, les boutons / / / , ne perdent pas fonctions de base respectives (insertion automatique/renvoi vidéo, activation répondeur vidéo et habilitation ouvre-porte automatique), car celles-ci ne peuvent être activées que lorsque la phonie est désactivée. 24 TONALITE D’APPEL A L’ETAGE Dans les postes internes du système 2GO!, il est possible de choisir parmi 5 tonalités d’appel à l’étage. Le choix des tonalités peut être effectué aussi par l’utilisateur final. Il suffit de procéder comme suit: 1. Tout en maintenant la touche ouvre-porte appuyée, appuyer et relâcher la touche . Le poste interne émet une sonnerie avec une tonalité. 2. En maintenant toujours la touche ouvre-porte appuyée, appuyer de nouveau sur la touche pour changer de tonalité. 3. Après avoir trouvé la tonalité désirée, relâcher la touche ouvre-porte . La tonalité est programmée. DS1707-002A EFFACEMENT DES PARAMETRES DE PROGRAMMATION (rétablissement des conditions de départ) Pour effacer tous les paramètres de programmation facultatifs, exécuter les opérations suivantes: 1. Tout en actionnant la touche , appuyer sur la touche . Le poste de vidéophone émet deux bips sonores pour signaler l’entrée en programmation. La touche se met à clignoter en rouge. 2. Actionner en même temps les touches et et les maintenir appuyées durant 3 secondes, jusqu’à entendre la tonalité qui confirme l’effacement. 3. Appuyer de nouveau sur le bouton du poste interne. Le vidéophone émet une tonalité de validation de la sortie de la programmation; la touche s’éteint. DS1707-002A 25 CONFIGURACIÓN DE LOS SOPORTES ESPAÑOL INSTALACIÓN • Fijar el soporte en la pared con los tornillos y los tacos, respetando las dimensiones laterales. 10 CODE: código de usuario. Configurar un número del 0 al 31 respetando la figura y las reglas que siguen: • En el sistema no debe haber apartamentos distintos con el mismo código de usuario. • Si en el mismo apartamento hay aparatos interiores en paralelo, deben tener el mismo código de usuario. • Los códigos de usuario de una misma columna de cables deben ser consecutivos. CODE cm 1 2 3 4 5 INT 10 1 2 3 4 5 USUARIO= 1 1 2 3 4 5 USUARIO= 2 1 2 3 4 5 USUARIO= 3 CODE ON ON 1 2 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 cm 1,55 m 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 • Conectar el cable de la línea bus no polarizada en los bornes LINE IN. • Si se utiliza la función de llamada al piso o un timbre adicional, conectar los conectores correspondientes. • Después de comprobar que los leds amarillos de los soportes estén apagados, se pueden montar los videointerfonos en los soportes. • Retirar la protección de cartón. • Enganchar el videointerfono como se ve en la figura. • Para reemplazar el videointerfono, pulsar el gancho y girar en el sentido de las agujas del reloj. USUARIO= 0 1 2 3 4 5 USUARIO= 4 USUARIO= 8 USUARIO= 12 USUARIO= 16 USUARIO= 20 USUARIO= 24 USUARIO= 28 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 USUARIO= 5 1 2 3 4 5 USUARIO= 9 1 2 3 4 5 USUARIO= 13 USUARIO= 17 USUARIO= 21 USUARIO= 25 USUARIO= 29 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 USUARIO= 6 USUARIO= 10 USUARIO= 14 USUARIO= 18 USUARIO= 22 USUARIO= 26 USUARIO= 30 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 USUARIO= 7 USUARIO= 11 USUARIO= 15 USUARIO= 19 USUARIO= 23 USUARIO= 27 USUARIO= 31 INT: código del interno del apartamento. Configurar un número del 0 al 3 respetando la figura y las reglas que siguen: • En el caso de un solo aparato interior presente en el apartamento, el código del interno debe ser siempre 0. • En los apartamentos se pueden conectar hasta 4 aparatos interiores en paralelo, todos con el mismo código de usuario pero con distintos códigos de interno. INT INT ON ON 1 2 1 2 3 4 5 1 2 INTERNO= 0 1 2 INTERNO= 1 1 2 INTERNO= 2 1 2 INTERNO= 3 El código del interno sirve para identificar los aparatos interiores individuales del mismo usuario. Esto permite realizar llamadas intercomunicantes dirigidas a un interno individual dentro del mismo apartamento. En el caso de llamadas intercomunicantes a distintos apartamentos, en el caso de llamadas procedentes de microaltavoces y en el caso de llamada al piso, suenan siempre todos los aparatos interiores del usuario. También hay que tener presentes las siguientes consideraciones: • Los internos 0 y 1, cuando reciben la llamada, suenan enseguida; los internos 2 y 3 suenan inmediatamente después. • Si la llamada llega de un microaltavoz videointerfónico, el interno 0 habilita el encendido del monitor. De todas formas, los otros aparatos interiores del mismo usuario pueden accionar el pulsador para encender su videointerfono apagando el otro (función ‘rebote vídeo’). α 26 CODE DS1707-002A DS1707-002A 27 FUNCIONAMIENTO VALORES PREDETERMINADOS 1 Todos los aparatos interiores salen de fábrica configurados de la siguiente manera: INT CODE ON ON 1 2 1 2 3 4 5 CODE = 31 INT =0 Z = ON ON Z: extremo de línea 2 De este modo, para el correcto funcionamiento del sistema hace falta prestar siempre atención a los interruptores dip para configurarlos con el valor correcto. 3 4 CONFIGURACIÓN DE LOS EXTREMOS DE LÍNEA 7 5 6 1 PULSADORES AUXILIARES: a utilizar para funciones especiales de acuerdo con el sistema. 2 JOYSTICK: para ajustar los parámetros vídeo. 3 PULSADOR DE AUTOACTIVACIÓN/REBOTE VÍDEO. 4 PULSADOR DE APERTURA DE LA PUERTA: se enciende de color verde durante el periodo de activación del videointerfono. Se enciende de color rojo para indicar la puerta abierta o se enciende rojo parpadeante para indicar la función de apertura automática de la puerta. 5 PULSADOR DE FONÍA: se enciende de color verde durante el periodo de activación del videointerfono. Pulsando la tecla se activa la fonía, el pulsador se enciende de color naranja. No es necesario mantener pulsada la tecla durante la conversación (función “MANOS LIBRES”). La conversación fónica se interrumpe cuando se acciona por segunda vez el pulsador o cuando se apaga el videointerfono. 6 MANDO DE REGULACIÓN DEL VOLUMEN DE LLAMADA/MUTE. 7 INDICACIÓN DE EXCLUSIÓN DE LLAMADA: la posición de Mute se pone de relieve con un banderín de indicación que sobresale del lado izquierdo del videointerfono. En los soportes de los aparatos interiores hay un interruptor que permite activar el extremo de línea. Es necesario activar el extremo en todos los dispositivos cableados al final de una línea que no vuelve a partir con otro tramo de los mismos bornes del dispositivo (final de línea). Extremo de línea ON Extremo de línea ON 10 82 /5 (IN 1 /O PA LI UT) TEN NE TE (D D ER LI ) NE ON OFF DESCRIPCIÓN DE LOS BORNES LINE IN LINE OUT CP S+; S- LIN E4 LIN E3 LIN E2 LIN E1 LIN E0 1 2 3 4 Extremo de línea OFF Extremo de línea ON Pareja de bornes a conectar con la línea no polarizada Pareja de bornes a utilizar para la conexión de la salida de la línea no polarizada Pareja de bornes a utilizar para la conexión de un pulsador de llamada al piso Pareja de bornes a utilizar para la conexión de un timbre adicional Extremo de línea ON 28 DS1707-002A DS1707-002A 29 RECEPCIÓN DE LAS LLAMADAS Y FUNCIÓN ‘REBOTE VÍDEO’ GESTIÓN DEL TIMBRE ADICIONAL Cuando se recibe una llamada, el aparato interior del usuario suena con la melodía configurada con la siguiente duración: El aparato interior tiene una pareja de bornes (S- y S+) para la conexión de un timbre adicional o de un relé. Este timbre se controla simultáneamente a la generación de cualquier timbre de llamada. PROCEDENCIA DE LA LLAMADA Llamada desde microaltavoz principal TIEMPO DURACIÓN TOTAL DEL TIMBRE 3s ON 3s Llamada desde microaltavoz secundario 0,4 seg. ON 0,2 seg. OFF 5 veces 2,8s Llamada intercomunicante 0,5 seg. ON 0,5 seg. OFF 3 veces 2,5s 3s ON 3s Llamada al piso RESUMEN DE LA FUNCIÓN DE LOS PULSADORES ESTADO Si el aparato interior está en reposo, es posible efectuar la autoactivación en el puesto “Master” accionando el pulsador . Accionar el pulsador para activar la comunicación audio con el microaltavoz “Master”; el usuario puede abrir la puerta en cualquier momento. Fonía OFF luego de una llamada recibida Llamada recibida y fonía ON Reposo y fonía ON Autoactivación en principal Rebote vídeo === Si está programado, llamada intercomunicante (3) o llamada a la centralita (1) Activación del contestador videointerfónico (1) Activación del alumbrado de las escaleras (2) Activación del alumbrado de las escaleras (2) Si está programado, llamada intercomunicante (3) Activación / desactivación apertura automática de la puerta === === Si está programado, llamada intercomunicante (3) === === === Si está programado, llamada intercomunicante (3) (1) (2) (3) Donde está previsto. Mediante decodificador Ref. 1082/80. O activación 2^ cerradura eléctrica mediante decodificador Ref. 1082/80. FUNCIÓN PUERTA ABIERTA DEL MICROALTAVOZ “MASTER” Si en el microaltavoz “Master” se conecta un sensor de puerta abierta en los bornes SP/GND, los aparatos interiores pueden controlar el estado físico de dicha puerta. Cuando la puerta está abierta, el pulsador se enciende de color rojo. ENVÍO DE LAS LLAMADAS INTERCOMUNICANTES Después de programar un pulsador ( / / / ) para la función intercomunicante (consultar el apartado referido a la programación de funciones adicionales), pulsar en secuencia la tecla y la tecla de llamada ( / / / ). Se pueden comprobar los siguientes casos según el estado del aparato interior llamado: • Aparato interior libre: el aparato interior que llama emite un tono de confirmación (2 bips) y el aparato interior llamado suena. Cuando se activa la fonía del aparato llamado, se establece la comunicación. • Aparato interior ocupado: el aparato interior que llama emite un tono de disuasión (4 bips rápidos); pulsar la tecla e intentar otra vez más tarde. FUNCIÓN DE LLAMADA AL PISO El aparato interior tiene una pareja de bornes (CP) para la conexión del pulsador de llamada al piso. Cuando se acciona el pulsador, el aparato interior emite un sonido de 3 seg. de duración con la melodía configurada. Si el usuario tiene varios aparatos interiores en paralelo, conectar este pulsador sólo en el interno 0. Los internos 0 y 1 sonarán enseguida; los internos 2 y 3 sonarán inmediatamente después. 30 / Reposo y fonía OFF PULSADOR FUNCIÓN DE AUTOACTIVACIÓN La función se puede activar/desactivar mediante el pulsador reservado . La activación de la función se indica con el encendido intermitente de la tecla de apertura de la puerta de color rojo. Activando esta función, con cada llamada que llegue de un teclado se accionará automáticamente la cerradura eléctrica. Si el usuario tiene varios internos en paralelo, activar la función en uno solo de los aparatos. / En la tabla que sigue se presenta un resumen de la función de las teclas según el estado del aparato interior: Desde la recepción de la llamada videointerfónica o interfónica, es siempre posible controlar la activación de la cerradura eléctrica del microaltavoz, incluso sin activar la fonía. Si en el apartamento hay varios aparatos interiores en paralelo, los internos 0 y 1 suenan enseguida; inmediatamente después suenan los internos 2 y 3. El interno 0 del usuario también controla el encendido del videointerfono si la llamada llega de un microaltavoz videointerfónico. En dicho caso, durante todo el tiempo de espera de activación de la fonía (60 seg. desde la llamada), los otros internos pueden encender su videointerfono accionando el pulsador de autoactivación (función ‘rebote vídeo’) hasta que se active la fonía de uno de los internos. Después de la activación de la fonía, la imagen estará presente sólo en el interno que tiene la fonía activa. La imagen de la cámara estará, pues, siempre presente en un solo monitor a la vez. FUNCIÓN DE APERTURA AUTOMÁTICA DE LA PUERTA / DS1707-002A PROGRAMACIÓN DE FUNCIONES ADICIONALES Después de controlar el funcionamiento básico del sistema, sólo si hacen falta las siguientes funciones es necesario realizar las operaciones de programación correspondientes. FUNCIÓN INTERCOMUNICANTE EN APARATO INTERIOR En el sistema 2GO! se pueden programar los pulsadores / / / de los aparatos interiores para la función de llamada intercomunicante. Un pulsador se puede programar para llamar a otro usuario del sistema o para llamar un aparato interior en paralelo. En el primer caso, suenan todos los aparatos interiores del usuario llamado; en el segundo caso, suena sólo el aparato interior especificado en la programación. DS1707-002A 31 FUNCIÓN INTERCOMUNICANTE ENTRE DISTINTOS USUARIOS 1. Ir al aparato interior que se debe programar como aparato que llama (aparato interior A). 2. Manteniendo pulsada la tecla , pulsar la tecla . El aparato interior A emite un tono para indicar la comienza a parpadear de color rojo. entrada en programación. La tecla A BEEP 3. Accionar el pulsador que se debe programar; el aparato interior emite un tono de confirmación. El pulsador puede ser / / / . FUNCIÓN INTERCOMUNICANTE EN EL MISMO APARTAMENTO El procedimiento de programación es el mismo que se describió para la programación de un pulsador para que cumpla la función intercomunicante entre distintos usuarios, a excepción de que es obligatorio concluir la programación pulsando la tecla de apertura de la puerta del videointerfono B que queremos llamar (consultar el paso 4 del apartado anterior), ya que no se puede llamar sólo el interno deseado desde el teclado. MELODÍA DE LLAMADA INTERFÓNICA En los aparatos interiores del sistema 2GO! se puede escoger entre 5 melodías de llamada. La elección de las melodías también puede ser realizada por el usuario final siguiendo estos sencillos pasos. , accionar y soltar el pulsador . El 1. Manteniendo apretado el pulsador de apertura de la puerta aparato interior emite un timbre con una melodía. , accionar otra vez el pulsador 2. Manteniendo siempre apretado el pulsador de apertura de la puerta para cambiar la melodía. 3. Cuando se encuentra la melodía deseada, soltar el pulsador de apertura de la puerta . La melodía está programada. A BEEP 4. Ir a lo del usuario que deberá llamar ese pulsador (usuario B) y accionar el pulsador de apertura de la puerta . Los aparatos interiores emiten un bip de programación completada. O bien, ir a un puesto de llamada y accionar el pulsador de llamada del usuario B; el aparato interior en programación (A) emite un bip de programación completada. Mientras se realiza esta operación, suenan los aparatos interiores del usuario B. Ignorar esta llamada. B BEEP MELODÍA DE LLAMADA AL PISO En los aparatos interiores del sistema 2GO! se puede escoger entre 5 melodías de llamada al piso. La elección de las melodías también puede ser realizada por el usuario final siguiendo estos sencillos pasos. 1. Manteniendo apretado el pulsador de apertura de la puerta , accionar y soltar el pulsador . El aparato interior emite un timbre con una melodía. 2. Manteniendo siempre apretado el pulsador de apertura de la puerta , accionar otra vez el pulsador para cambiar la melodía. 3. Cuando se encuentra la melodía deseada, soltar el pulsador de apertura de la puerta . La melodía está programada. USUARIO B 5. Accionar otra vez el pulsador del aparato interior A, que emite un bip de salida de la programación. La tecla se apaga. 6. Comprobar la función programada: accionar el pulsador del aparato interior A y luego accionar el pulsador programado. Comprobar que suenen todos los aparatos interiores del usuario B; accionar el pulsador de un videointerfono B y comprobar que pueda comunicarse con el aparato interior A. 7. Si también se quiere programar la llamada inversa, es necesario programar el aparato interior B para la llamada a A. § sus Los pulsadores / / / , incluso si se programan con la función intercomunicante, no pierden funciones básicas de autoactivación/rebote vídeo, activación del contestador videointerfónico y CANCELACIÓN DE LOS DATOS DE PROGRAMACIÓN (restablecimiento de las condiciones iniciales) Para cancelar todos los datos opcionales de programación, llevar a cabo las siguientes operaciones: 1. Manteniendo pulsada la tecla , pulsar la tecla . El aparato videointerfónico emite dos bips para indicar la entrada en programación. La tecla comienza a parpadear de color rojo. 2. Pulsar simultáneamente las teclas y y mantenerlas pulsadas por 3 segundos hasta que se emita un tono que confirma la cancelación. 3. Accionar nuevamente el pulsador del aparato interior. El videointerfono emite un tono de confirmación de la salida de la programación; la tecla se apaga. 32 DS1707-002A activación de la apertura automática de la puerta, respectivamente, ya que estas funciones se pueden activar sólo con la fonía desactivada. DS1707-002A 33 KONFIGURATION DER HALTERUNGEN DEUTSCH INSTALLATION • Die Halterung mit Schrauben und Dübeln unter Berücksichtigung des seitlichen Platzbedarfs an der Wand befestigen. 10 cm CODE: Benutzercode. Geben Sie eine Zahl von 0 bis 31 gemäß der folgenden Abbildung und den Anweisungen im Anschluss ein: • Es dürfen auf der Anlage keine unterschiedlichen Wohnungen mit demselben Teilnehmer-Code vorliegen. • Bei parallel geschalteten Innenstellen in derselben Wohnung müssen diese über denselben TeilnehmerCode verfügen. • Die Teilnehmer-Codes derselben Sammelleitung müssen aufeinander folgen. CODE 1 2 3 4 5 INT 10 1 2 3 4 5 TEILNEHM.= 1 1 2 3 4 5 TEILNEHM.= 2 1 2 3 4 5 TEILNEHM.= 3 CODE ON ON 1 2 1 2 3 4 5 1 2 3 4 5 cm 1 2 3 4 5 1,55 m 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 • Das Kabel der ungepolten Busleitung an die LINE IN-Klemmen anschließen. • Sollte die Funktion des Etagenrufs eingesetzt werden oder ein zusätzliches Läutwerk, die entsprechenden Leiter anschließen. • Nachdem überprüft wurde, dass die gelben Leds der Halterungen ausgeschaltet sind, können die Videoanlagen auf die Halterungen montiert werden. • Die Kartonabdeckung der Halterung entfernen. • Die Videoanlage wie im Bild befestigen. • Um die Videoanlage zu ersetzen, den Haken drücken und im Uhrzeigersinn drehen. TEILNEHM.= 0 1 2 3 4 5 1 2 3 4 5 TEILNEHM.= 4 TEILNEHM.= 8 TEILNEHM.= 12 TEILNEHM.= 16 TEILNEHM.= 20 TEILNEHM.= 24 TEILNEHM.= 28 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 TEILNEHM.= 5 1 2 3 4 5 TEILNEHM.= 9 1 2 3 4 5 TEILNEHM.= 13 TEILNEHM.= 17 TEILNEHM.= 21 TEILNEHM.= 25 TEILNEHM.= 29 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 TEILNEHM.= 6 TEILNEHM.= 10 TEILNEHM.= 14 TEILNEHM.= 18 TEILNEHM.= 22 TEILNEHM.= 26 TEILNEHM.= 30 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 TEILNEHM.= 7 TEILNEHM.= 11 TEILNEHM.= 15 TEILNEHM.= 19 TEILNEHM.= 23 TEILNEHM.= 27 TEILNEHM.= 31 INT: Code der Innenstelle der Wohnung. Geben Sie eine Zahl von 0 bis 3 gemäß der folgenden Abbildung und den Anweisungen im Anschluss ein: • Bei nur einer Innenstelle in der Wohnung, muss der Innenstellen-Code mit 0 eingegeben werden. • In den Wohnungen ist es möglich, bis zu 4 Innenstellen parallel zu schalten, die alle denselben TeilnehmerCode aufweisen, aber verschiedene Innenstellen-Codes. INT INT ON ON 1 2 1 2 3 4 5 1 2 INTERNE STATION= 0 1 2 INTERNE STATION= 1 1 2 INTERNE STATION= 2 1 2 INTERNE STATION= 3 Der Innenstellen-Code dient der Identifizierung der einzelnen Innenstellen desselben Teilnehmers. Dies gestattet interkommunizierende Anrufe, die an die einzelne Innenstelle innerhalb derselben Wohnung gerichtet sind. Bei interkommunizierenden Anrufen an verschiedene Wohnungen und im Fall von Anrufen von Außenstellen und im Fall von Etagenrufen klingeln stets alle Innenstellen des Teilnehmers. Ferner muss Folgendes berücksichtigt werden: • Die Innenstellen 0 und 1 klingeln bei Erhalt des Anrufs sofort, die Innenstellen 2 und 3 unmittelbar danach. • Kommt der Anruf von einer Außenstelle für Videoanlagen, aktiviert die Innenstelle 0 das Einschalten des Monitors. Die anderen Innenstellen desselben Teilnehmers können in jedem Fall die Taste drücken, um ihren Videoanlage ein- und den anderen auszuschalten (Funktion der Bildweiterleitung). α 34 CODE DS1707-002A DS1707-002A 35 FUNKTIONSWEISE STANDARDWERTE 1 Alle Außenstellen sind werkseitig wie folgt konfiguriert: INT CODE ON ON 1 2 1 2 3 4 5 CODE = 31 INT =0 Z = ON ON Z: leitungsabschluss 2 Auf diese Weise ist es für die korrekte Funktionsweise der Anlage stets erforderlich, auf die Dip-Switches zu achten, um diese auf den korrekten Wert einzustellen. 3 4 EINSTELLUNG DER LEITUNGSABSCHLÜSSE 7 5 6 Auf den Außenstellen und den Innenstellen befindet sich ein Schalter, der das Einsetzen eines Leitungsabschlusses gestattet. Es ist erforderlich, den Abschluss in allen am Ende einer Leitung, die nicht mit einem anderen Abschnitt von denselben Klemmen des Geräts weiterführt, verkabelten Geräten zu aktivieren (Leitungsende). Abschluss ON Abschluss ON Abschluss OFF Abschluss ON 1 NEBENTASTEN: verwendbar für Sonderfunktionen abhängig von der Anlage. 2 JOYSTICK: zur Einstellung der Videoparameter. 3 TASTE ZUR SELBSTEINSCHALTUNG/BILDWEITERLEITUNG. 4 TÜRÖFFNERTASTE: leuchtet während der Einschaltdauer der Videoanlage grün auf. Leuchtet rot auf, um die geöffnete Tür anzuzeigen oder blinkt rot, um die automatische Türöffnerfunktion anzuzeigen. 5 SPRECHTASTE: leuchtet während der Einschaltdauer der Videoanlage grün auf. Durch Betätigen der Taste wird das Gespräch aktiviert und die Taste leuchtet orange auf. Es ist nicht erforderlich, die Taste während des Gesprächs gedrückt zu halten (Funktion „FREIHAND“). Das Gespräch wird durch erneutes Drücken der Taste unterbrochen oder im Moment des Ausschaltens der Videoanlage. 6 BEDIENUNG EINSTELLUNG DER RUFLAUTSTÄRKE/MUTE. 7 ANZEIGE RUFAUSSCHLUSS: Die Position Mute wird durch das Austreten einer Kennzeichnung auf der linken Seite der Videoanlage angezeigt. 10 82 /5 (IN 1 /O PA LI UT) TEN NE TE (D D ER LI ) NE BESCHREIBUNG DER KLEMMEN LINE IN LINE OUT CP S+; S- An die ungepolte Leitung anzuschließendes Klemmenpaar Für den Anschluss des Ausgangs der ungepolten Leitung zu verwendendes Klemmenpaar Für den Anschluss einer Taste des Etagenrufs zu verwendendes Klemmenpaar Für den Anschluss eines zusätzlichen Läutwerks zu verwendendes Klemmenpaar LIN E4 LIN E3 LIN E2 LIN E1 LIN E0 1 2 3 4 ON OFF Abschluss ON 36 DS1707-002A DS1707-002A 37 RUFENTGEGENNAHME UND FUNKTION DER VIDEOBILDWEITERLEITUNG VERWALTUNG VON ZUSATZLÄUTWERKEN Beim Empfang eines Anrufs ertönt auf der Innenstelle des Teilnehmers die gemäß der folgenden Zeiten eingegebene Melodie: Die Innenstelle ist mit einem Klemmenpaar (S-, S+) für den Anschluss eines Zusatzläutwerks oder eines Relais ausgestattet. Dieses Läutwerk wird gleichzeitig mit der Erzeugung eines jeglichen Klingelzeichens gesteuert. AUSGANGSPUNKT DES ANRUFS ZEITEN GESAMTDAUER DES KLINGELNS Anruf von Haupt-Außenstelle 3s ON 3s Anruf von Neben-Außenstelle 0,4s ON 0,2s OFF 5 Mal 2,8s Interkommunizierender Anruf 0,5s ON 0,5s OFF 3 Mal 2,5s 3s ON 3s Etagenruf Ab dem Empfang des Anrufs von der Video- oder Sprechanlage ist es stets möglich, die Aktivierung der Elektroverriegelung der Außenstelle zu steuern, auch ohne das Gespräch zu aktivieren. Wenn sich in der Wohnung mehrere parallel geschaltete Innenstellen befinden, läuten die Innenstellen 0 und 1 sofort und unmittelbar danach die Innenstellen 2 und 3. Die Innenstelle des Teilnehmers 0 steuert auch das Einschalten der Videoanlage, wenn der Anruf von einer Außenstelle einer Videoanlage kommt. In diesem Fall können während der gesamten Wartezeit vor der Aktivierung des Gesprächs (60 s ab Anruf) die anderen Innenstellen ihre Videoanlage durch Betätigen der Taste der Selbsteinschaltung einschalten (Bildweiterleitungsfunktion), bis das Gespräch einer der Innenstellen aktiviert wird. Nach der Aktivierung des Gesprächs ist das Bild nur noch auf der Innenstelle zu sehen, deren Gespräch aktiviert wurde. Das Bild der Kamera ist daher stets nur auf jeweils einer Videoanlage zu sehen. ZUSAMMENFASSUNG DER TASTENFUNKTIONEN AUTOMATISCHE TÜRÖFFNERFUNKTION Die Funktion ist über die spezielle Taste ein- und ausschaltbar. Die Aktivierung der Funktion wird durch das intermittierende Einschalten der Türöffnertaste in rot angezeigt. Durch Aktivieren dieser Funktion wird bei jedem Anruf von einem Tastenfeld aus automatisch die Elektroverriegelung betätigt. Verfügt der Teilnehmer über mehrere parallel geschaltete Innenstellen, die Funktion nur auf einem Gerät einschalten. / / In der Tabelle im Anschluss sind die Funktionen de Tasten in Bezug auf den Status der Innenstelle zusammengefasst: STATUS Ruhestellung Gespräch OFF Gespräch OFF im Anschluss an erhaltenen Anruf Anruf erhalten und Gespräch ON Ruhestellung Gespräch ON Selbsteinschaltung auf Hauptstelle Bildweiterleitung === Bei programmiertem Intercom-Anruf (3) oder Anruf an die Zentrale (1) Aktivierung Aufzeichnungsgerät für Videoanlagen (1) Aktivierung des Treppenlichts (2) Aktivierung des Treppenlichts (2) Bei programmiertem Intercom-Anruf (3) Aktivierung/ Deaktivierung automatischer Türöffner === === Bei programmiertem Intercom-Anruf (3) === === === Bei programmiertem Intercom-Anruf (3) TASTE SELBSTEINSCHALTUNGSFUNKTION Befindet sich die Innenstelle in Ruhestellung kann die Selbsteinschaltung auf der “Master”-Station durch Betätigen der Taste erfolgen. Die Taste betätigen, um die Audiokommunikation mit der “Master”-Außenstelle zu aktivieren. Der Teilnehmer kann die Tür jederzeit öffnen. / (1) (2) (3) Wo vorgesehen. Mit Decoder Typ 1082/80. Oder Aktivierung 2. Elektroverriegelung über Decoder Typ 1082/80. FUNKTION TÜR GEÖFFNET DER „MASTER“-AUSSENSTELLE Wenn auf der ‘Master’-Außenstelle ein Sensor zum Erfassen der geöffneten Tür auf den Klemmen SP/GND angeschlossen wird, können die Innenstellen den physischen Zustand dieser Tür überwachen. Ist die Tür geöffnet, leuchtet die Taste rot auf. WEITERLEITUNG DER INTERCOM-ANRUFE Nachdem eine Taste ( / / / ) für die Intercom-Funktion programmiert wurde (siehe Absatz hinsichtlich der Programmierung von Zusatzfunktionen), anschließend die Taste und die Ruftaste ( / / / ) betätigen. Es können abhängig vom Status der angerufenen Innenstelle die folgenden Fälle eintreten: • Innenstelle frei: die anrufende Innenstelle gibt einen Ton zur Bestätigung aus (2 Tonsignale) und die angerufene Innenstelle klingelt. Bei der Aktivierung des Gesprächs der angerufenen Person, wird die Verbindung hergestellt. • Innenstelle besetzt: Die anrufende Innenstelle sendet einen Benachrichtigungston (4 schnell Pfeiftöne) aus. Die Taste betätigen und später erneut versuchen. ETAGENRUFFUNKTION Die Innenstelle ist mit einem Klemmenpaar (CP) für den Anschluss der Taste des Etagenrufs ausgestattet. Beim Drücken der Taste gibt die Innenstelle ein Klingeln mit einer Dauer von 3 Sec mit der eingegebenen Melodie aus. Verfügt der Teilnehmer über mehrere parallel geschaltete Innenstellen, diese Taste nur auf der Innnestelle 0 anschließen. Die Innenstellen 0 und 1 läuten sofort. Die Innenstellen 2 und 3 läuten unmittelbar danach. 38 DS1707-002A PROGRAMMIERUNG ZUSATZFUNKTIONEN Nachdem die grundlegende Funktion des Systems überprüft wurde, ist es, nur wenn die folgenden Merkmale gewünscht sind, erforderlich, die entsprechenden Programmiervorgänge durchzuführen. INTERKOMMUNIZIERENDE FUNKTION AUF INNENSTELLE Im System 2GO! können die Tasten und Innenstellen / / / für die Funktion des interkommunizierenden Rufs programmiert werden. Eine Taste kann darauf programmiert werden, einen anderen Teilnehmer der Anlage oder eine parallel geschaltete Innenstelle anzurufen. Im ersten Fall klingeln alle Innenstellen des angerufenen Teilnehmers, im zweiten klingelt nur die während der Programmierung angegebene Innenstelle. DS1707-002A 39 INTERKOMMUNIZIERENDE FUNKTION UNTER VERSCHIEDENEN TEILNEHMERN 1. Begeben Sie sich zur als anrufend zu programmierenden Innenstelle (Innenstelle A). 2. Bei gedrückter Taste die Taste betätigen. Die Innenstelle A sendet einen Ton aus, um den Eintritt beginnt rot zu leuchten. in die Programmierung anzuzeigen. Die Taste A BEEP 3. Die zu programmierende Taste drücken. Die Innenstelle sendet einen Ton zur Bestätigung aus. Die Taste kann sein / / / . INTERKOMMUNIZIERENDE FUNKTION INNERHALB DERSELBEN WOHNUNG Der Programmiervorgang ist derselbe wie der zuvor für das Programmieren einer Taste zum Erfüllen der Intercom-Funktion unter verschiedenen Teilnehmern beschriebene mit der Ausnahme, dass es obligatorisch ist, die Programmierung durch Betätigen der Türöffnertaste der Videoanlage B abzuschließen, die wir anrufen möchten (siehe Schritt 4 des vorangegangenen Absatzes), da nicht nur die gewünschte Innenstelle vom Tastenfeld angerufen werden kann. MELODIE DES ANRUFS VON DER SPRECHANLAGE Auf den Innenstellen des Systems 2GO! kann zwischen 5 Rufmelodien gewählt werden. Die Auswahl der Melodie kann auch vom Endbenutzer in dieser einfachen Reihenfolge ausgeführt werden. die Taste drücken und loslassen. Die Innenstelle sendet 1. Unter Gedrückthalten der Türöffnertaste ein Klingeln mit einer Melodie aus. 2. Unter weiterem Gedrückthalten der Türöffnertaste die Taste erneut drücken, um die Melodie zu ändern. 3. Ertönt die gewünschte Melodie, die Türöffnertaste loslassen. Die Melodie ist programmiert. A BEEP 4. Begeben Sie sich zu dem Teilnehmer, den diese Taste anrufen soll (Teilnehmer B) und drücken Sie die Türöffnertaste . Die Innenstellen senden ein Tonsignal der erfolgten Programmierung aus. Oder Sie begeben sich zu einer Rufeinheit und drücken die Ruftaste des Teilnehmers B. Die Innenstelle in Programmierung (A) sendet ein Tonsignal der erfolgten Programmierung aus. Gleichzeitig klingeln während dieses Vorgangs die Innenstellen des Teilnehmers B. Vernachlässigen Sie diesen Anruf. B BEEP MELODIE DES ETAGENRUFS Auf den Innenstellen des Systems 2GO! kann zwischen 5 Melodien für den Etagenruf gewählt werden. Die Auswahl der Melodie kann auch vom Endbenutzer in dieser einfachen Reihenfolge ausgeführt werden. 1. Unter Gedrückthalten der Türöffnertaste die Taste drücken und loslassen. Die Innenstelle sendet ein Klingeln mit einer Melodie aus. 2. Unter weiterem Gedrückthalten der Türöffnertaste die Taste erneut drücken, um die Melodie zu ändern. 3. Ertönt die gewünschte Melodie, die Türöffnertaste loslassen. Die Melodie ist programmiert. BENUTZER B 5. Die Taste der Innenstelle A erneut betätigen, die ein Tonsignal des Verlassens der Programmierung aussendet. Die Taste schaltet sich aus. 6. Die programmierte Funktion überprüfen: die Taste . der Innenstelle A betätigen und dann die programmierte Taste. Überprüfen, ob alle Innenstellen des Teilnehmers B läuten. Die Taste . einer Videoanlage B betätigen und überprüfen, ob mit der Innenstelle A kommuniziert werden kann. 7. Soll auch der umgekehrte Ruf programmiert werden können, muss auch die Innenstelle B für den Anruf nach A programmiert werden. § Die Tasten / / / verlieren, auch wenn sie mit der Intercom-Funktion programmiert werden, nicht ihre jeweiligen Grundfunktionen der Selbsteinschaltung/Bildweiterleitung, Aktivierung des Video- LÖSCHEN DER PROGRAMMIERDATEN (Wiederherstellung der Ausgangsbedingungen) Um alle Extradaten der Programmierung zu löschen, die folgenden Vorgänge ausführen: 1. Bei gedrückter Taste die Taste betätigen. Die Stelle der Videoanlage sendet zwei Pfeiftöne aus, um den Beginn der Programmierung anzuzeigen. Die Taste . beginnt rot zu leuchten. 2. Gleichzeitig die Tasten und drücken und drei Sekunden lang gedrückt halten, bis der Signalton des erfolgten Löschens ertönt. 3. Erneut die Taste . der Innenstelle betätigen. Die Videoanlage sendet einen Ton zur Bestätigung des Verlassens der Programmierung aus. Die Taste . schaltet sich aus. 40 DS1707-002A Aufzeichnungsgeräts und Aktivierung des automatischen Türöffners, da diese Funktionen nur bei deaktiviertem Gespräch einschaltbar sind. DS1707-002A 41 42 DS1707-002A DS1707-002A 43 DS 1707-002A FILIALI 20151 MILANO - V.Gallarate 218 Tel. 02.380.111.75 - Fax 02.380.111.80 00043 CIAMPINO (ROMA) V.L. Einaudi 17/19A Tel. 06.791.07.30 - Fax 06.791.48.97 80013 CASALNUOVO (NA) V.Nazionale delle Puglie 3 Tel. 081.193.661.20 - Fax 081.193.661.04 30030 VIGONOVO (VE) - V.del Lavoro 71 Tel. 049.738.63.00 r.a. - Fax 049.738.63.11 66020 S.GIOVANNI TEATINO (CH) - V.Nenni 17 Loc. Sambuceto Tel. 085.44.64.851 Tel. 085.44.64.033 - Fax 085.44.61.862 LBT 8282 SEDE URMET DOMUS S.p.A. 10154 TORINO (ITALY) VIA BOLOGNA 188/C Telef. +39 011.24.00.000 (RIC. AUT.) Fax +39 011.24.00.300 - 323 Area tecnica servizio clienti +39 011.23.39.810 http://www.urmetdomus.com e-mail:[email protected]