accessori per serramenti
Transcript
accessori per serramenti
accessori per serramenti R R C D M A N C E REEEGGGUUULLLAAATTTIIIOOONNNOOOFFFC COOONNNSSSTTTRRRUUUCCCTTTIIIOOONNNPPPRRROOODDDUUUCCCTTTSSS333000555///222000111111---D DEEECCCLLLAAARRRAAATTTIIIOOONNNOOOFFFPPPEEERRRFFFOOORRRM MA AN NC CE E n° 1. rev. 0.1 010-CPR-2014-02-03 Unique identification code of the product-type Hinge Loira+ Type, batch or serial number or any other element allowing identification of the construction product as required pursuant to Article 11(4) 2. 3. Loira+ - 2 knuckles 7000 – 7000I – 7010 – 7010I – 7020 - 7030 – 7040 – 7040I – 7050 – 7050I – 7060 – 7070 - 7090 – 7000V – 7000VI – 7010V – 7010VI – 7020V – 7030V – 7040V – 7040VI – 7050V – 7050VI – 7060V - 7070V - 7090V Loira+ - 3 knuckles 7003 – 7013 – 7013I – 7023 – 7033 – 7043 – 7053 – 7063 – 7073 - 7093 – 7003V – 7013V – 7013VI – 7023V – 7033V – 7043V – 7053V – 7063V – 7073V - 7093V Loira+ TR 2 knuckles 7100 – 7100I – 7110 Loira+ TR 3 knuckles 7103 Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification as foreseen by the manufacturer Use on escape route doors Name, registered trade name or registered mark and contact address of the manufacturer as required pursuant to Article 11(5) 4. FAPIM S.p.A. - Via delle Cerbaie, 114 – 55011 Altopascio (LU) – Italy Phone +39 0583 2601 – fax +39 0583 25291 – e-mail: [email protected] – www.fapim.it 5. Name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12 § 2 6. System or systems of assessment and verification of the constancy of performance of the construction product as set out in Annex V: In case of the declaration of performance concerning a construction product covered by a harmonised standard the notified factory product control certification body Not applicable System 1 UNI EN 1935:2004 + EC1:2007 ICIM S.p.A. - n° 0425 with headquarters in Piazza Don Mapelli, 75 – 20099 Sesto San Giovanni (MI) – Italy 7. under system 1 has performed the: determination of the product type on the basis of type testing (including sampling) of the product, initial inspection of the manufacturing plant and of factory production control, continuous surveillance, the assessment and evaluation of factory production control and has issued the certificate of constancy of performance, n° 0425-CPR-2600 8. In case of the declaration of performance concerning a construction product for which a European Technical Assessment has been issued Not applicable DECLARED PERFORMANCE Essential characteristics § 5.1 initial friction torque measurements Performance Harmonised technical specification ≤ 4 Nm Lateral displacement under load: ≤ 2 mm Vertical displacement under load: ≤ 4 mm § 5.2.1 static load: load-deformation 9. No breakage nor any cracking or deformation visible to normal or corrected vision Self closing § 5.1 – 5.2 - 5.3 5.6 Lateral and vertical residual displacements after unloading are within the shaded area in fig. G1 § 5.2.2 static load: overload No breakage nor any cracking or deformation visible to normal or corrected vision UNI EN 1935:2004 + EC1:2007 The hinge is still connected to the frame § 5.3 shear strength § 5.6 hinges for use on fire-resistant and / or smokecontrol doors Loira+ and TR 2 knuckles: suitability Loira+ and TR 3 knuckles: not suitability Not suitability FAPIM SpA - 55011 Altopascio (LUCCA) – Via Delle Cerbaie, 114 – Tel. +39 0583 2601 – Telefax +39 0583 25291 www.fapim.it [email protected] Cap. Soc. € 10.000.000 i.v. – Reg.Imp.Lucca, C.F., P.I. n° 02224030466 – R.E.A. LU 207647 – Ident. N. IT 02224030466 pag. 1 di 2 accessori per serramenti DECLARED PERFORMANCE Essential characteristics Durability 9. § 5.4 – 5.5 – 5.8 Dangerous substances Harmonised technical specification Performance § 5.4 durability; number of cycles 200.000 – grade 7 § 5.4 durability: lateral and vertical wear The lateral and vertical wear are within the shaded area in fig. G2 § 5.4 durability: maximum permissible frictional torque measured after the first 20 cycles and after completion of the test ≤ 4 Nm § 5.5 corrosion resistance Grade 4 (240 h): very high resistance, according to EN 1670 § 5.8 families of hinges with common design features Loira+ Note 1 annex ZA.1 Materials in products don’t contain or release any dangerous substances in excess of the maximum levels specified in existing European material standards or any national regulations Classification of the hinge UNI EN 1935:2004 + EC1:2007 Regulation 305/2011 Loira+ 2 knuckles UNI EN 1935:2004 + EC1:2007 Art. 6 § 3 - d 4 7 7 0 1 4 1 14 Category of use Durability Mass of the door Fire / smoke suitability Safety Corrosion resistance Security – Burglar resistance Hinge grade Classification of the hinge Regulation 305/2011 Loira+ 3 knuckles Art. 6 § 3 - d 4 7 7 0 1 4 0 14 Category of use Durability Mass of the door Fire / smoke suitability Safety Corrosion resistance Security – Burglar resistance Hinge grade Classification of the hinge Regulation 305/2011 Loira+ 2 knuckles: art. 7070 – 7070V Art. 6 § 3 - d 4 7 6 0 1 4 1 13 Category of use Durability Mass of the door Fire / smoke suitability Safety Corrosion resistance Security – Burglar resistance Hinge grade Classification of the hinge Regulation 305/2011 Loira+ TR 3 knuckles: art. 7073 – 7073V - 7103 Art. 6 § 3 - d 4 7 6 0 1 4 0 13 Category of use Durability Mass of the door Fire / smoke suitability Safety Corrosion resistance Security – Burglar resistance Hinge grade Classification of the hinge 4 Category of use Regulation 305/2011 Loira+ TR 2 knuckles: art. 7100 – 7100I - 7110 7 5 Durability Mass of the door 0 1 Fire / smoke suitability Safety Art. 6 § 3 - d 4 1 12 Corrosion resistance Security – Burglar resistance Hinge grade The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4. 10. Name Eng. Raffaele Vezzosi Function Quality System and Product Certification manager Altopascio, 2014/02/03 FAPIM SpA - 55011 Altopascio (LUCCA) – Via Delle Cerbaie, 114 – Tel. +39 0583 2601 – Telefax +39 0583 25291 www.fapim.it [email protected] Cap. Soc. € 10.000.000 i.v. – Reg.Imp.Lucca, C.F., P.I. n° 02224030466 – R.E.A. LU 207647 – Ident. N. IT 02224030466 pag. 2 di 2