ISTRUZIONI DI MONTAGGIO 24014/C A50
Transcript
ISTRUZIONI DI MONTAGGIO 24014/C A50
Tel. +39 075.5280260 Fax +39 075.5287033 Via Pizzoni 37/39 06132 Perugia ITALY www.umbrarimorchi.it [email protected] ISTRUZIONI DI MONTAGGIO FITTING INSTRUCTIONS INSTRUCTIONS DE MONTAGE MONTAGEANLEITUNG INSTRUCCIONES DE MONTAJE DISPOSITIVO DI TRAINO TIPO TOWING BRACKET TYPE DISPOTIF DE REMORQUAGE TYPE ANHAENGEVORRICHTUNG TYP DISPOSITIVO DE CAREO TIPO 24014/C PER AUTOVEICOLI FOR CARS POUR AUTOS FUR KRAFTAHRZEUGE PARA AUTOVEHICULO MITSUBISHI COLT ‘04 Z30 TYPE CLASSE E TIPO DI ATTACCO CLASS AND HITCH TYPE CLASSE ET TYPE DE CROCHET KLASSE UND BEFESTIGUNGSART CLASES DE ACOPLAMIENTO A50-X OMOLOGAZIONE 2004 CARICO VERTICALE MAX S VALUE MASSE VERTICALE MAXIMUM ZUL. STUETZLAST CARGA MAX. VERTICAL HOMOLOGATION HOMOLOGATION ZULASSUNG APROBACION e3 00 – 7199 S = kg 70 (DIR. 94/20/CE) VALORE D D VALUE VALEUR D D WERT VALOR D 6,7 kN D = 6,7 kN COPPIA DI SERRAGGIO PER VITI (8.8): TORQUE SETTINGS FOR NUTS AND BOLTS (8.8): COUPLE DE SERRAGE POUR VIS (8.8): SCHRAUBENANZUGSMOMENT (8.8): MOM. DE PRESION PARA TORNILLOS Y TUERCAS (8.8): Cod. 24014/C - Mitsubishi Colt - => v. 1.0 01/01/2011 M6 = 10 Nm M10 = 55 Nm M14 = 135 Nm M8 = 25 Nm M12 = 85 Nm M16 = 200 Nm P. 1 / 7 SAFETY INSTRUCTIONS Make sure that the towbar is suitable for the vehicle before starting the installation. For safety, all work involving towbar installation (incl. electrical components) must be undertaken by skilled technicians. Damaged components must be replaced with manufacturer’s spares and fitted by qualified staff. It is forbidden to make any modification or structural repair to towing assembly. The towball must be kept clean and lubricated. For added safety, his diameter (50 mm) must be checked at regular intervals. If the towball measures less than 49 mm after selected readings across the diameter, the towball must be replaced with a new one. After 1000 km of towing, check torque settings for nuts and bolts, in accordance with the table. Umbra Rimorchi cannot be held responsible for any defects in the product caused by fault or by any injudicious use whatever of the user or a person he is liable for. Cod. 24014/C - Mitsubishi Colt - v. 1.0 01/01/2011 P. 2 / 7 FITTING INSTRUCTIONS 24014 • • • • • • • • • • • • • • • MITSUBISHI COLT Remove any mastic from contact points then paint with anti rust paint. 1 Remove bumper. 2 Remove the rubber support of the exhaust which is located under the boot, in correspondence of the right chassis rail. 3 Remove the plastic support which is under the boot in correspondence of the left chassis rail. 4 Locate the C supports (left and right) in correspondence of the holes 02 and 03 on the rear part of the chassis rails. Insert the screws and fit. 5 Insert 2 cylinder caged nuts M8 in correspondence of holes 05 that are on the left chassis rail of the vehicle. 6 Locate side arms B, left and right in correspondence of the holes 04, 05,06. Insert the screws and fit. 7 Interpose cross bar a to side arms B in correspondence of holes 01, insert the screws and fit. 8 Tighten all bolts and nuts as per torque settings. 9 Connect the wirings to the socket. 10 Re-fit the rubber support of the exhaust. 11 Re-fit the plastic hose support. 12 Cut a hole in correspondence of the lower central part of bumper, as per layout 01. 13 Re-fit bumper. Cod. 24014/C - Mitsubishi Colt - v. 1.0 01/01/2011 P. 3 / 7 Cod. 24014/C - Mitsubishi Colt - v. 1.0 01/01/2011 P. 4 / 7 Cod. 24014/C - Mitsubishi Colt - v. 1.0 01/01/2011 P. 5 / 7 Cod. 24014/C - Mitsubishi Colt - v. 1.0 01/01/2011 P. 6 / 7 Cod. 24014/C - Mitsubishi Colt - v. 1.0 01/01/2011 P. 7 / 7