Manuale di configurazione Cattura Dati SIPAX
Transcript
Manuale di configurazione Cattura Dati SIPAX
Manuale di configurazione Cattura Dati SIPAX Business Development Group 4 Novembre 2004 Preparato da: Roberto Manuzzi Configurazione Cattura dati SIPAX Support Document INDICE TAVOLA DELLE REVISIONI……………………………………………… 3 1.0 OBIETTIVI DEL PROGETTO…………………………………... 1.1 BENEFICI DEL PRODOTTO…………………………………… 1.2 ARCHITETTURA GENERALE…………………………………. 4 4 4 2.0 CONFIGURAZIONE DELLA POSTAZIONE SIPAX 2.1 PROCEDURE PER LA CONDIVISIONE DELLE RISORSE 2.2 CONDIVISIONE DELLA DIRECTORY “BOS” 5 7 12 3.0 Procedure da eseguire nel caso in cui il protocolo TCP/IP non sia preconfigurato nell’immagine dell’installazione 4.0 Verifica del file IBMLAN.INI 18 5.0 VISUALIZZAZIONE DELLA DIRECTORY CONDIVISA SULLE MACCHINE WINDOWS DELLA RETE LOCALE Confidential Pag 2 of 40 Business Development Group 27 35 Configurazione cattura dati SIPAX Support Document TAVOLA DELLE REVISIONI Nun Data Ver: Revisione: Modifica Effettuata da: Modifica Sezione #: (1) Tipo modifica: 04/11/04 27/12/04 27/12/04 R. Manuzzi R. Manuzzi R. Manuzzi Tutte 2.2 3.0 Creazione Aggiunta Modifica 27/12/04 R. Manuzzi 4.0 Modifica 27/12/04 R. Manuzzi 3.0 Modifica (1) Tipo di Cambiamento Creazione Aggiunta Modifica Chiarimento Eliminazione Descrizione Revisione: Cambio num. paragrafo Cambio num. paragrafo Cambio num. paragrafo Configurazione cattura dati SIPAX Support Document 1.0 Obiettivi del Progetto Questo manuale e’ stato scritto per aiutarvi nella configurazione della cattura dati sulla postazione SIPAX e per condividere la Directory contenenti I file dei biglietti catturati sulla rete locale 1.1 Benefici del prodotto La nuova cattura dati Sipax di Trenitalia permettera’ alle agenzie Sabre di poter contabilizzare tramite I programmi di backoffice gia’ oggi utilizzati per la biglietteria aerea anche la biglietteria ferroviaria. 1.2 Architettura Generale La configurazione di seguito riportata permettera’ alla postazione SIPAX di catturare dei file contenenti I dati salienti dei biglietti emessi per poter essere poi elaborati dai vari programmi di back-office. I File catturati verranno depositati su una directory nel disco C della postazione SIPAX, questo indifferentemente se si sta utilizzando una postazione SIPAX –PRO, SIPAX-NET o SIPAX Via X.25. Per poter condividere la cartella del disco C della postazione SIPAX, e’ indispensabile invece trovarsi in un’agenzia con connettivita’ IP, quindi con un prodotto del tipo SIPAX-PRO oppure SIPAX-NET, non sara’ possibile condividere tale cartella se ci troviamo in un’agenzia con SIPAX Via X.25, questo in quanto e’ necessario essere muniti di piattaforma OS2/ WARP 4, disponibile appunto solo con connettivita’ IP. Configurazione cattura dati SIPAX 2.0 Support Document Configurazione della postazione SIPAX Per poter configurare la postazione SIPAX e’ necessario operare con l’applicazione SIPAX chiusa. Per prima cosa provvediamo a creare la directory dove verranno scaricati I file, apriamo quindi una shell di OS/2 , come in figura e digitiamo al prompt: “MD BOS”, quindi premere invio. A tal punto sempre dalla shell OS/2 posizionamoci sulla directory C:\SIPAX31\BIN E digitiamo il comando “pv3prof sipax3.prf”, come in figura : Confidential Pag 2 of 40 Business Development Group Configurazione cattura dati SIPAX Support Document Apparira’ la seguente schermata: Nell’ultima Riga , quella relativa al BACK-OFFICE scriviamo la directory appena creata dove verranno depositati I file, ovvero: “C:\BOS” Confidential Page 7 Business Development Group Configurazione cattura dati SIPAX Support Document Quindi premiamo Il tasto ESCI in fondo a sinistra: Ora riavviamo correttamente il computer, ed al prossimo riavvio del SIPAX tutti I biglietti emessi verranno anche catturati e depositati nella cartella “C:\BOS”. 2.1 Procedure per la condivisione delle risorse A questo punto, per poter condividere I file catturati da SIPAX con la macchina di Back-office occorrera’ condividere la cartella BOS con il resto della rete locale. Tale procedura puo’ variare a seconda della release dell’immagine con la quale e’ stata installata la postazione SIPAX. Nel caso sia una agenzia installata a partire dal secondo semestre 2004 , quasi sicuramente e’ gia’ stata predisposta e configurata con il protocollo TCP/IP necessario alla condivisione, altrimenti occorrera’ configurarla opportunamente. Di seguito analizziamo il primo caso: Dal desktop di OS/2 clicchiamo sull’icona “Connection” Confidential Page 8 Business Development Group Configurazione cattura dati SIPAX Support Document E di seguito, come in figura clicchiamo su “ Network”: Alla finestra successiva clicchiamo sull’icona “Network Services”: E quindi sull’icona “Sharing and Connection”: Confidential Page 9 Business Development Group Configurazione cattura dati SIPAX Support Document Cliccando su tale icona si aprira’ la seguente finestra : Dove nella casella Password digiteremo: “DBA”, che ovviamente non sara’ leggibile: Confidential Page 10 Business Development Group Configurazione cattura dati SIPAX Support Document Verranno visualizzate le seguenti schermate: Confidential Page 11 Business Development Group Configurazione cattura dati SIPAX Support Document 2.2 CONDIVISIONE DELLA DIRECTORY “BOS” Ora provvediamo a condividere la directory interessata: Di seguito,il desktop di OS/2 dove cliccando sul cassettino posizionato sopra l’icona del Floppy-disk comparira l’Icona dei vari dischi del computer: e clicchiamo sull’icona indicata: Confidential Page 12 Business Development Group Configurazione cattura dati SIPAX Support Document A tal punto avremo la seguente schermata: Dove evidenziando la directory a noi necessaria (“BOS”), clicchiamo con il tasto destro del mouse , ed apriamo la voce “Properties” Posizionamo il mouse sulla voce “Shares” in alto a destra : Confidential Page 13 Business Development Group Configurazione cattura dati SIPAX Support Document Scriviamo nel campo “Description” la dicitura “Backoffice Sipax” Clicchiamo sul tasto “Manage access” : Confidential Page 14 Business Development Group Configurazione cattura dati SIPAX Support Document Ed apparira’ la seguente schermata : dove dovremo cliccare sull’opzione “Read/write”, come qui sotto mostrato e quindi cliccare su “OK”. Confidential Page 15 Business Development Group Configurazione cattura dati SIPAX Support Document Apparira’ il seguente messaggio: Clicchiamo su “OK” ed alla successiva schermata cliccare su “Save”: Confidential Page 16 Business Development Group Configurazione cattura dati SIPAX Support Document Apparira’ la seguente schermata: Confidential Page 17 Business Development Group Configurazione cattura dati SIPAX Support Document Quindi potremo chiudere tranquillamente : A questo punto avremo condiviso correttamente la directory “BOS”. Confidential Page 18 Business Development Group Configurazione cattura dati SIPAX Support Document 3.0 Procedure da eseguire nel caso in cui il protocollo TCP/IP non sia preconfigurato nell’immagine dell’installazione Nel caso in cui abbiamo di fronte una Workstation SIPAX installata anteriormente al secondo semestre 2004, e’ possibile che il protocollo TCP/IP necessario per la condivisione della WS Sipax sulla rete Windows non sia stato configurato, in tal caso dovremo procedere come segue: PER PRIMA COSA E’ CONSIGLIABILE SALVARE I SEGUENTI FILE : CONFIG.SYS che troveremo sulla root in C: PROTOCOL.INI che troveremo sotto la directory C:\IBMCOM IBMLAN.INI che troveremo sotto la directory C:\IBMLAN Si Consiglia vivamente di salvarli sia su Floppy disk che sulla root del Disco D:. Tali file saranno necessari in caso di errore a ripristinare la situazione iniziale. Partendo dal desktop di OS/2 apriamo dalla barra degli strumenti il programma MPTS (vedi figura) Si aprira’ la seguente finestra: Confidential Page 19 Business Development Group Configurazione cattura dati SIPAX Support Document Dare OK Cliccare sul tasto “Continuare” Confidential Page 20 Business Development Group Configurazione cattura dati SIPAX Support Document Cliccare su “Configure” ,dovrebbe apparira’ una schermata simile alla seguente: Se la maschera che appare riporta gli stessi protocolli rappresentati in figura nella parte in basso denominata “Current Configuration”, allora la postazione e’ gia’ Confidential Page 21 Business Development Group Configurazione cattura dati SIPAX Support Document correttamente configurata e non dovremo continuare nella configurazione, quindi si puo’ uscire premendo il tasto CANCEL . Se invece I protocolli sono diversi occorrera’ configurare correttamente la WS seguendo la procedura descritta sotto, di seguito e’ raffigurata la finestra con non tutti I protocolli configurati: Dapprima dovremo Rimuovere I protocolli presenti evidenziandoli uno ad uno e cliccando ogni volta sul tasto “Remove” e dando conferma, -FARE MOLTA ATTENZIONE A NON RIMUOVERE ANCHE L’ADATTATORE DI RETE-, (nell’esempio “3Com Fast Etherlink/EtherLink XL Family OS/2, ma potrebbe essere diverso, in quanto esistono diversi modelli di schede di rete). Una volta che avremo presente in figura il solo adattattore di rete potremo selezionare uno alla volta ,dalla Finestra in alto a destra, I vari protocolli e li aggiungeremo premendo il tasto “ADD “. Confidential Page 22 Business Development Group Configurazione cattura dati SIPAX Support Document Seguire esattamente la sequenza raffigurata nelle figure seguenti: Confidential Page 23 Business Development Group Configurazione cattura dati SIPAX Support Document Ora e’ necessario cambiare numero di ADATTATORE al protocollo “IBM OS/2 NETBIOS OVER TCP/IP, per far cio’ lo evidenziamo e premiamo il tasto “Change number”. Confidential Page 24 Business Development Group Configurazione cattura dati SIPAX Support Document Avremo la seguente figura: Selezionamo il numero “1” e premiamo il tasto “Change” il risultato sara’, ora premiamo “OK” : Confidential Page 25 Business Development Group Configurazione cattura dati SIPAX Support Document Di seguito appariranno le seguenti maschere dove dovremo sempre dare conferma: Confidential Page 26 Business Development Group Configurazione cattura dati SIPAX Support Document A tal punto dovremo fare il REBOOT della macchina. Confidential Page 27 Business Development Group Configurazione cattura dati SIPAX 4.0 Support Document Verifica del file “IBMLAN.INI” Ora andiamo a verificare se nel file IBMLAN.INI che troveremo nella directory C:\IBMLAN siano presenti alcuni parametri.Per far cio’ andremo ad editare il file usando dalla finestra OS/2 il comando “E IBMLAN.INI” ovviamente stando posizionati nella directory contenente il file (vedi figura sotto). Dando invio si aprira’ l’EDITOR con il file IBMLAN.INI Confidential Page 28 Business Development Group Configurazione cattura dati SIPAX Support Document Di seguito troverete allegato il contenuto di un file IBMLAN.INI Occorre verificare SOLO ed ESCLUSIVAMENTE la presenza delle tre RIGHE EVIDENZIATE IN NERO ed Eventualmente AGGIUNGERE cio’ che manca come descritto in ROSSO -----------------------INIZIO FILE------------------------------------------------------; OS/2 LAN Requester initialization file [networks] net1 = NETBEUI$,0,LM10,34,100,14 net2 = TCPBEUI$,1,LM10,34,70,14 Aggiungere questa riga ; This information is read by the redirector at device initialization time. [requester] COMPUTERNAME = SABREX45 DOMAIN = ETS ; The following parameters generally do not need to be ; changed by the user. charcount = 16 chartime = 250 charwait = 3600 keepconn = 600 keepsearch = 600 maxcmds = 16 maxerrorlog = 100 maxthreads = 10 maxwrkcache = 64 numalerts = 12 numcharbuf = 10 numservices = 7 numworkbuf = 40 numdgrambuf = 14 othdomains = printbuftime = 90 sesstimeout = 45 sizcharbuf = 512 sizerror = 1024 sizworkbuf = 4096 useallmem = Yes ; The wrkheuristics parameter sets a variety of requester fine-tuning ; options. Brief descriptions are provided here for each digit. More ; complete descriptions, along with explanations of relationships between ; digits can be found in the LAN Server Network Administrator Reference ; Volume 2: Performance Tuning. Confidential Page 29 Business Development Group Configurazione cattura dati SIPAX Support Document ; ; When not otherwise specified, a value of 0 means off (inactive) and 1 means ; on (active). ; ; 0 opportunistic locking of files (default is 1) ; 1 performance optimization for batch (.CMD) files (default is 1) ; 2 asynchronous unlock and asynchronous write-unlock ; 0 = never 2 = only on a LAN Server virtual circuit ; 1 = always (default) ; 3 asynchronous close and asynchronous write-close ; 0 = never 2 = only on a LAN Server virtual circuit ; 1 = always (default) ; 4 buffer all named pipes and serial devices (default is 1) ; 5 combined read-lock and write-unlock ; 0 = never 2 = only on a LAN Server virtual circuit ; 1 = always (default) ; 6 open and read optimization (default is 1) ; 7 reserved ; 8 use of the chain-send NETBIOS NCB ; 0 = never ; 1 = when a server's buffer is larger than the workstations buffer ; 2 = always (default) ; 9 buffer small read and write requests until the buffer is full ; 0 = never 2 = only on a LAN Server virtual circuit ; 1 = always (default) ; 10 buffer mode ; 0 = always read buffer size amount of data if the request is smaller ; than the buffer size (sizworkbuf) and data is being read ; sequentially ; 1 = use full buffer if file is open for reading and writing ; 2 = use full buffer if reading and writing sequentially ; 3 = buffer all requests smaller than the buffer size (if hits occur) ; (default) ; 11 RAW read and RAW write SMB protocols (default is 1) ; 12 RAW read-ahead buffer (default is 1) ; 13 RAW write-behind buffer (default is 1) ; 14 read multiplexing SMB protocols (default is 1) ; 15 write multiplexing SMB protocols (default is 1) ; 16 use of big buffers for large core (non-RAW) reads (default is 1) ; 17 same-size read-ahead or read-to-sector boundary (default is 1) ; 18 same-size small record write-behind or write-to-sector boundary ; (default is 0) ; 19 reserved and must be 0 ; 20 flush pipes and devices on a DosBufReset or DosClose operation ; 0 = Flush only files and devices opened by the caller. Spin until ; flushed. Wait for confirmation before processing with other ; tasks. (default) ; 1 = Flush only files and devices opened by the caller. Flush only ; once. Do not wait for confirmation. ; 2 = Flush all files and all input and output of short-term pipes Confidential Page 30 Business Development Group Configurazione cattura dati SIPAX Support Document ; and devices. Spin until flushed. ; 3 = Flush all files and all input and output of short-term pipes ; and devices. Flush only once. ; 4 = Flush all files and all input and output of all pipes and devices. ; Spin until flushed. ; 5 = Flush all files and all input and output of all pipes and devices. ; Flush only once. ; 21 LAN Server encryption of passwords (default is 1) ; 22 control log entries for multiple occurrences of an error ; 0 = log all occurrences (default) ; 1-9 = limit occurrences that are logged (1-9 define size of table ; that is used to track errors) ; 23 buffer all files opened with deny-write sharing mode (default is 1) ; 24 buffer all files opened with the read-only attribute set (default is 1) ; 25 read ahead when opening for execution (default is 1) ; 26 handle the interrupt (ctrl+c) key ; 0 = allow no interrupts ; 1 = allow interrupts only on long-term operations ; 2 = always allow interrupts (default) ; 27 force correct open mode when creating files on a core server (reserved ; for DBCS users) (default is 1) ; 28 NETBIOS NoAck mode ; 0 = NoAck is disabled. ; 1 = NoAck is set on send only. (default) ; 2 = NoAck is set on receive only. ; 3 = NoAck is set on send and receive. ; 29 send data along with SMB write-block RAW requests (default is 1) ; 30 send a message to the screen when the requester logs an error ; 0 = never ; 1 = on write-fault errors only (no time out) (default) ; 2 = on write-fault and internal errors only (no time out) ; 3 = on all errors (no time out) ; 4 = reserved ; 5 = on write-fault errors only (time out) ; 6 = on write-fault and internal errors only (time out) ; 7 = on all errors (time out) ; 8 = on all errors (time out) and pop up an error if a session ; to a server is abnormally disconnected ; 9 = on all errors (time out) and generate an INT24 (critical ; error) to applications running under DOS emulation if a ; network hard error is encountered ; 31 reserved ; 32 behavior of DosBufReset on a redirected file (not pipes or devices). ; When the call to the API returns, the data in the buffer has been ; handled as follows: ; 0 = Changed data in the buffer was sent from the requester to the ; server. The server has written the data to disk. ; 1 = Changed data in the buffer was sent from the requester to the ; server. The server has not yet written the data to disk. ; 2 = DosBufReset was ignored. (default) Confidential Page 31 Business Development Group Configurazione cattura dati SIPAX Support Document ; 33 time interval for performing logon validation from the domain ; controller ; 0 = 5 seconds 4 = 60 seconds 8 = 8 minutes ; 1 = 15 seconds (default) 5 = 90 seconds 9 = 15 minutes ; 2 = 30 seconds 6 = 2 minutes ; 3 = 45 seconds 7 = 4 minutes ; 34 date validation ; 0 = PCLP date format (default) ; 1 = MSNET date format ; 2 = assume date is correct ; 35 free disk space reported to DOS and Windows applications ; 0 = return true value (default) ; 1 = return a value less than two gigabytes ; 36 time and date synchronization with the domain controller at logon ; (default is 1) ; 37 type of verification for the LAN Server logon ; 0 = no verification ; 1 = verify against local NET.ACC ; 2 = verify against domain NET.ACC (default) ; 38 display warning messages for the LAN Server logon ; 0 = do not display warning messages ; 1 = display all warning messages (default) ; 2 = do not display LAN Server specific warning messages ; 3 = display all warning messages, including password expiration date ; 39 buffer all files opened in compatibility mode ; 0 = buffer only files opened for read access in compatibility mode ; 1 = buffer all files opened in compatibility mode (default) ; 40 allow a user to logon multiple times in the same domain (default is 1) ; ; The next lines help you to locate bits in the wrkheuristics entry. ; 1 2 3 4 ; 0123456789012345678901234567890123456789012 wrkheuristics = 1111111121311111110001011120111221001111100 wrkservices = PEER,MESSENGER wrknets = net1,NET2 AGGIUNGERE “NET2” [messenger] logfile = messages.log sizmessbuf = 4096 [peer] auditing = resource ; The following parameters generally do not need to be ; changed by the user. NOTE : srvnets= is represented in ; the server info struct as a 16-bit lan mask. Srvnet names ; are converted to indexes within [networks] for the named nets. guestacct = guest autodisconnect = -1 Confidential Page 32 Business Development Group Configurazione cattura dati SIPAX Support Document maxauditlog = 100 maxchdevjob = 2 maxchdevs = 1 maxconnections = 26 maxlocks = 64 maxopens = 160 maxsearches = 150 maxsessopens = 80 maxsessreqs = 25 maxsessvcs = 1 maxshares = 16 maxusers = 5 numbigbuf = 4 numfiletasks = 1 numreqbuf = 48 sizreqbuf = 4096 srvhidden = yes ; The srvheuristics parameter sets a variety of server fine-tuning ; options. Brief descriptions are provided here for each digit. More ; complete descriptions, along with explanations of relationships between ; digits can be found in the LAN Server Network Administrator Reference ; Volume 2: Performance Tuning. ; ; When not otherwise specified, a value of 0 means off (inactive) and 1 means ; on (active). ; ; 0 opportunistic locking of files (default is 1) ; 1 read-ahead when the requester is performing sequential access ; 0 = do not use read-ahead ; 1 = use single read-ahead thread (default) ; 2 = use asynchronous read-ahead thread ; 2 write-behind (default is 1) ; 3 use of the chain-send NETBIOS NCB (default is 1) ; 4 check all incoming SMBs for correct format (default is 0) ; 5 support FCB opens (default is 1) ; 6 set priority of server (default is 4) ; 0-9 = 0 is highest priority, 9 is lowest priority ; 7 automatically allocate additional memory for directory searches ; (default is 1) ; 8 write records to the audit log only when the scavenger wakes up ; (default is 1) ; 9 do full buffering when a file is opened with deny-write sharing mode ; (default is 1) ; 10 set the interval for the scavenger to wake up ; 0 = 5 seconds 4 = 25 seconds 8 = 45 seconds ; 1 = 10 seconds (default) 5 = 30 seconds 9 = 50 seconds ; 2 = 15 seconds 6 = 35 seconds ; 3 = 20 seconds 7 = 40 seconds ; 11 allow compatibility-mode opens of certain types of files by translating ; them to sharing mode opens with deny-none Confidential Page 33 Business Development Group Configurazione cattura dati SIPAX Support Document ; 0 = Always use compatibility-mode opens. ; 1 = Use deny-none sharing mode if read-only access to .EXE or .COM ; files. ; 2 = Use deny-none sharing mode if read-only access to .EXE or .COM ; files. Use deny-write sharing mode if read-only access to .BAT ; files is requested. ; 3 = Use deny-none sharing mode on all compatibility-mode opens. ; (default) ; 12 allow DOS LAN Services workstations to use a second NETBIOS session when ; sending printer requests (default is 1) ; 13 number of 64KB buffers used for read-ahead ; 0-9 = number of buffers (default is 1) ; 14 convert incoming path specifications into most basic format (default is 0) ; 15 Oplock Timeout and NETBIOS Acknowledgment Timeout (default is 0) ; 0 = 35 second Oplock Timeout; 34 second NETBIOS Acknowledgment Timeout ; 1 = 70 second Oplock Timeout; 69 second NETBIOS Acknowledgment Timeout ; 2 = 140 second Oplock Timeout; 127 second NETBIOS Acknowledgment Timeout ; 3 = 210 second Oplock Timeout; 127 second NETBIOS Acknowledgment Timeout ; 4 = 280 second Oplock Timeout; 127 second NETBIOS Acknowledgment Timeout ; 5 = 350 second Oplock Timeout; 127 second NETBIOS Acknowledgment Timeout ; 6 = 420 second Oplock Timeout; 127 second NETBIOS Acknowledgment Timeout ; 7 = 490 second Oplock Timeout; 127 second NETBIOS Acknowledgment Timeout ; 8 = 560 second Oplock Timeout; 127 second NETBIOS Acknowledgment Timeout ; 9 = 640 second Oplock Timeout; no NETBIOS Acknowledgment Timeout ; 16 validate IOCTLs (default is 1) ; 17 how long the server maintains unused, dynamic big buffers before freeing ; the memory. ; 0 = 0 seconds 4 = 5 minutes 8 = 1 hour ; 1 = 1 second 5 = 10 minutes 9 = indefinitely ; 2 = 10 seconds 6 = 20 minutes ; 3 = 1 minute (default) 7 = 40 minutes ; 18 how long the server waits after failing to allocate a big buffer before ; trying again. ; 0 = 0 seconds 3 = 1 minute (default) ; 1 = 1 second 4 = 5 minutes ; 2 = 10 seconds 5 = 10 minutes ; 19 RAW read and RAW write SMB protocols (default is 1) ; 20 server responds to announcement requests (default is 1) ; ; The next lines help you to locate bits in the srvheuristics entry. ; 1 2 ; 012345678901234567890 srvheuristics = 111101411113110013311 Confidential Page 34 Business Development Group Configurazione cattura dati SIPAX Support Document SRVSERVICES = srvnets = NET1,NET2 AGGIUNGERE “NET2” SRVCOMMENT = IWSSipax [replicator] replicate = IMPORT importpath = C:\ibmlan\repl\import tryuser = yes password = [services] ; Correlates name of service to pathname of service program. ; The pathname must be either ; 1) an absolute path (including the drive specification) ; OR ; 2) a path relative to the IBMLAN root messenger = services\msrvinit.exe peer = services\peerinit.exe replicator = services\replicat.exe requester = services\wksta.exe ---------------------------FINE FILE---------------------------------------------------------- Salviamo il File e riavviamo la macchina. Come gia’ detto in precedenza I passi descritti ne presente capitolo sono necessari solo se la macchina non e’ stata installata con un disco immagine recente, altrimenti tali configurazioni sono gia’ presenti nella workstation. N.B. La descrizione e le specifiche dei File generati dalla Cattura dati SIPAX sono contenuti in un’altro documento redatto daTrenitalia ed IBM che possiamo fornire a richiesta alle agenzie. Confidential Page 35 Business Development Group Configurazione cattura dati SIPAX Support Document 5.0 Visualizzazione della directory condivisa dalle macchine Windows della rete locale. Dalle macchine Windows 98 occorre innanzitutto eseguire una disconnessione dell’utente in uso per accedere con l’utente chiamato DBA: Da START/AVVIO scegliere “Disconnettere…(nome utente)”, Scegliere “SI” e alla richiesta di nome utente/password digitare DBA in Nome Utente, lasciare la password in bianco e premere OK: andare su “Trova Computer” ed inserire o il nome del computer OS/2 che a meno di modifiche in fase di installazione e’ sempre uno dei seguenti: “SABREX45” “TRAVEX16” oppure tramite il numero di IP Confidential Page 36 Business Development Group Configurazione cattura dati SIPAX Support Document Quindi: Finalmente potremo vedere la cartellina “BOS”: Confidential Page 37 Business Development Group Configurazione cattura dati SIPAX Support Document Dove, al suo interno troveremo I file catturati: Per quanto riguarda le macchine Windows XP posizionarsi su Trova computer: Confidential Page 38 Business Development Group Configurazione cattura dati SIPAX Support Document Quindi inserire il nome del computer o il numero di IP: Confidential Page 39 Business Development Group Configurazione cattura dati SIPAX Support Document Si aprira’ la finestra di richiesta User name and password: Introdurre nella casella Nome Utente: “DBA” e dare l’OK Confidential Page 40 Business Development Group Configurazione cattura dati SIPAX Support Document Cosi facendo si visualizzera’ la seguente finestra : Dove possiamo vedere ed aprire la directory BOS contenente I file dei biglietti Sipax catturati: Confidential Page 41 Business Development Group