C24_gsm_utenteV1.5-EN

C24-GSM
ALARM CONTROL UNIT (24 INPUTS)
WITH INTEGRATED GSM COMMUNICATOR
USER MANUAL
ENGLISH
DESCRIPTION
C24 GSM is an alarm control unit with 24 inputs and integrated GSM communicator, which uses the existing
cellular network to send SPEECH, Ademco CONTACT ID digital protocol and SMS text messages when
triggered. The system is completely remote controlled and it can be programmed through a local keypad or
by SMS text messages sent to the system. From keybaord it’s possible to listen which zones has been in
alarm or which zones are not ready when arming.
The main features of the system are:
24 Input Zones separately programmable and configurable ( 8 on board + 16 on remote input boards )
8 Programmable O.C. outputs for remote and local ( by user’s menu on keypad ) switching of external devices
1 Total arming program
3 Partial arming programs
Compatibility with S serie devices
- up to 4 keypads
- up to 2 remote inputs
- up to 4 remote key plugs
12 user codes
8 telephone numbers that can be programmed for vocal and/or SMS notifications
8 telephone numbers that can be programmed for transmission of digital protocol Contact ID
200 telephone that can be programmed to control a single PGM output
1 STATUS Input (SYS) used to check a remote device’s state or for remote arming / disarming
1 Input with ON/OFF function that can be used for remote activation of the system (AWAY)
1 Input with ON/OFF function that can be used for partial remote activation of the system (STAY)
1 RESET Input for the local reset of alarm
1 Output for notification of GSM system ERROR
1 Output for notification of AWAY arming
1 Output for notification of STAY arming
1 LED for notification of GSM cellular network signal strength OK (Green LED)
1 LED for notification of GSM module operation (Yellow LED)
1 LED for notification of system error (Red LED)
Simulated PSTN line, which allows to call with a normal touch tone telephone or connect an hardwired
communicator
1 Output for RING simulation of entering calls, which can be used for connections with other devices
User Menu operation guided by vocal prompts
Possibility to trigger an output by calling the system from one of the programmed telephone numbers.
Possibility to send SMS to the system from a certain telephone number to programme or change parameters, arm / disarm the system, enable/disable PGM outputs, query its status: to do any of these operations
a password is required. Once the SMS has been received, the system sends an SMS back to the first
number to confirm the action.
Possibility to trigger one or more output by calling the system with a single ring from one of the programmed
telephone numbers. System waits for a single ring and recognizes the associated telephone number, from
which the call has been performed. Once the output has been activated the system will ring back the calling
telephone to confirm the action.
SIM card credit remaining control
www.amcelettronica.com
C24 GSM v1.5
index
DESCRIPTION.............................................................................................................................
INDEX .......................................................................................................................................
KEYBORD USER MANU.............................................................................................................
SPEECH MENU...........................................................................................................................
ARM / DISARM THE CONTROL UNIT BY KEYPAD....................................................................
SIGNALLING LED ON KEYPAD..................................................................................................
ARM / DISARM THE CONTROL UNIT BY REMOTE PLUG........................................................
PROXIMITY PROXIMITY SMALL................................................................................................
MENU EVENTS............................................................................................................................
2
3
4
5
6
6
7
8
read events
............................................................................................................................................ 8
MENU INPUT STATUS............................................................................................................................. 8
MENU ACTIVATE OUTPUTS.................................................................................................................... 8
MENU CHANGE PERSONAL CODE........................................................................................... 8
KEYS PROGRAMMING ........................................................................................................................... 8
DELETE KEYS ......................................................................................................................................... 8
MANAGEMENT SIM CREDIT................................................................................................................... 9
MENU DATE / TIME..................................................................................................................... 9
date
/ time
. ............................................................................................................................................. 9
PLANNING AND MANAGEMENT BY SMS MESSAGES............................................................ 10
operations
- user. ...................................................................................................................................... 10
.................................................................................... 10
use of sms text messages for remote programming
ARM / DISARM THE CONTROL UNIT VIA GMS......................................................................... 11
how to write a programming sms................................................................................................................. 12
CALLS AND MANAGEMENT BY VOICE GUIDANCE................................................................. 13
call to the system...................................................................................................................................... 13
user vocal menu......................................................................................................................................... 13
EVENTS LIST............................................................................................................................... 14
www.amcelettronica.com
C24 GSM v1.5
KEYBOARD - USER MENU
PERSONAL
CODE
USER Code
111111
(DEFAULT user 01= 111111)
Down
Arrow (V)
0= Total 2= Partial 02 1= Partial 01 3= Partial 03
Note: in order to exclude some inputs press “*” on keypad and select the input with
“Cancel” key
ARM
SYSTEM
(V)
MENU
EVENTS
(V)
INPUT
STATUS
Enter
(✔)
[ 01 ]
Input Nr 01
●●●●●●●●●●●●●●●●
□ = Opened input
● = Closed input
(V)
ACTIVATE
OUTPUTS
(✔)
(V)
CHANGE
PERSONAL CODE
D = Deactivated
E = Activated
I = Pulsed Activated
- = Disable ( assigned specific function )
(✔)
CODE:
111111
(✔)
PROGRAM KEY
* Prog.
# Esc
(✔)
DELETE KEY
* Go
# Esc
User Nr xx
(V)
KEYS
PROGRAMMING
(V)
KEYS
DELETING
(V)
Tel. TIM
40916
CREDIT
MANAGEMENT
CHANGE VOLUME
(✔)
Level
VOLUME
Tel. VODAFONE
404
3
Tel. wind
4155
(V)
Speakerphone
MENU
DATE/TIME
(✔)
Tel. other
0
Sms TIM
PRE CRE SIN
Sun 01/01/00
00 : 00 : 00
Sms VODAFONE
Sms WIND
SALDO
www.amcelettronica.com
3
Sms OTHER
C24 GSM v1.5
SPEECH MENU
Press # key
Dial personal code
Code
wrong
Press # key
Personal code
wrong
Code ok
Dial 1 to act on the
system
1 = arm partial 1
2 = arm partial 2
3 = arm partial 3
4 = arm total
5 = Disarm
# = to esc
Dial 2 to use the
remote controls
Dial 3 to check the
status of the system
Select output
# = to quit
System armed: total / partial
System disarmed
Dial 1 to enable
Dial 2 to disable
Dial 3 to enable with pulse
1 to check the status of the system
2 to check the status of the zones
3 to check the status of the outputs
# to quit
Dial 4 to connect to
a remote system
www.amcelettronica.com
Output 1 enabled
Output 2 disabled
Output 3 enabled with pulse
System Status = System armed / disarmed
Inputs = SYS ( to record ); from 1 to 24 opened / closed
Outputs = from 1 to 8 enabled / disabled
Wait
4
C24 GSM v1.5
ENTER AND MOVE THROUGH THE MENU
➣ Key in the user code (000000 default) and confirm with RETURN (✔).
ENTER CODE
[✻✻✻✻✻✻]
➣ Use arrows keys up and down (↑↓) to move to the various submenus.
➣ Press RETURN (✔) to modify the menu.
➣ Use the keypad to key in numbers and alphanumeric strings.
➣ Use the CANCEL (✘) key to erase parameters or to activate the squares assignment (□).
➣ Use the # to exit from the menu; after 60” of inactivity the system automatically returns to home screen.
ARM / DISARM THE CONTROL UNIT BY KEYPAD
MENU ARM SYSTEM
It’s possible done four arming types: total (fig. 1), Partial 1.2 or 3 (fig. 2).
➣ Press RETURN (✔).
➣ Select 0 for Total, 1 for Partial 1, 2 for Partial 2 , 3 for Partial 3.
➣ Confirm with RETURN (✔).
➣ The display will show the exit time remaining (fig. 3).
➣ when the system is armed the display will indicate the date, time and the program armed (ex in Figure 4).
fig.1
fig.3
PROGRAM:
Total
ARMING
ON GOING...
PROGRAM:
Partial 01
fig.2
01/01/10 - 12:00
fig.4
Total Armed
[30]
➣ To disarm the system simply re-enter your personal code (default 111111).
In the case of inputs left open the system will notify you and ask how to act.
In the figures below there are two zones remained open; the control unit asks what to do.
02 Unready Zones
02 Unready Zones
1 -> Include
2 -> Exclude
www.amcelettronica.com
5
02 Unready Zones
3 -> Select
C24 GSM v1.5
SIGNALLING LED ON KEYPAD
The keypad has 3 leds:
Yellow Led -- system status: armed, disarmed
Red Led -- memory events: if turned on, there is ana event to read, otherwise there are not events.
Green Led -- indicates the status of the zones (if turned on ,all the zones are closed).
ARM / DISARM THE CONTROL UNIT BY REMOTE PLUG
The figure below shows the indications given by the 4 LEDs of the plug.
➣ To total arm the unit just insert the key and remove it when the first three LEDs are lit. When the system
is armed, the LEDs remain lit.
➣ To Partial arm the unit simply insert the key and remove it when the Partial corresponding led is lit: Partial1 orange, Partial2 yellow, Partial3 red.
When the system is partialy armed the corresponding LED lights up.
Please note that the green LED indicates that all inputs are closed and that the Alarm Memory signaling
(simultaneous flashing LED orange, yellow and red) is detected only when the system is armed.
The alarm memory is reset after a disarming of the system (by keyboard, remotely by phone or by SMS), or
after reading the event log.
www.amcelettronica.com
6
C24 GSM v1.5
PROXIMITY
Connecting led, used to notify
the key reading and they stay
ONn to signal that the reader
is working. It’s possible to do
a new operation when these
leds are all OFF.
Led signalling system status (arm/disarm):
- all ON = total arm
- 1° led from left orange = program 1 arm
- 2° led from left yellow = program 2 arm
- 3° led from left red = program 3 arm
4° led from left green = inputs status (turned
on when all zones are closed)
Way of working:
Move the key (mod. Beatle) near the reader, all the connecting leds turn on and also the signalling leds turn
on. Remove the key when is visualized the type of arming chosen (total = all3 leds on, partial1,...)
note: close all the tampers in order to do the system working correctly.
PROXIMITY SMALL
All OFF
Led signalling Arming
- all on= total arm
-- orange led on (right bottom part BD) = program 1
- orange yellow on (left top AS) = program 2
- red led on (right top part AD) = program 3
- green led on (left bottom part BD) = status zones: (on when
zones are in standby)
During an alarm all the leds except for BS flash.
www.amcelettronica.com
7
C24 GSM v1.5
MENU EVENTS
EVENTS READING
With this menu it is possible to read in a chronological way all events from the last happened to the older
one.
➣ Once in the menu use arrow keys up and down to scroll all events.
MENU INPUT STATUS
With this parameter you can check the status of the inputs (open or closed).
➣ once you enter the menu, press ENTER (✔), and use the arrow keys to scroll through the open zones.
MENU ACTIVATE OUTPUTS
With this parameter you can activate the outputs planned in advance.
➣ once you enter the menu, press ENTER (✔), and use the arrow keys # and * to scroll the output to be
activated, with the arrow keys up and down you can turn in the following ways:
up arrow = output stably activated --> E symbol
down arrow = output pulsed activated --> I symbol
output deactivated --> D symbol
MENU CHANGE PERSONAL CODE
With this parameter you can change the personal code.
➣ once you enter the menu, press ENTER (✔), and use the number keys to change your code.
KEYS PROGRAMMING
With this parameter you can program keys and / or transponder.
➣after entering the menu, press ENTER (✔) to access to the form of activation:
✻ = to start the process of key writing
# = to interrupt the process of key writing
To program press the activation button and insert key, or bring it closer if it’s a proximity key; wait until the
LEDs turn off, pull the programmed key. Repeat for all keys in possession.
PROGRAM KEY
✻ Prog.
# Esci
DELETE KEY
With this parameter, you can cancel your key code.
➣ once you enter the menu, press ENTER (✔) for access to the form of cancellation:
✻ = to start the process of key cancellation
# = to exit the process of key cancellation
After performing this procedure the code entered on the key no longer works.
www.amcelettronica.com
8
C24 GSM v1.5
MANAGEMENT SIM CREDIT
With this parameter you can know the remaining credit of the SIM ( it works for the major mobile operators
) and insert the parameters for the request.
For the 3 main italian operators the parameters are inserted by default. For all the other providers, there are
the “Tel.Other Menu” and “SMS Other Menu”
The value of available credit is updated every time the panel makes an operation (vocal/SMS/CID). The
SMS received by the provider is displayed.
➣ once you enter the menu, press ENTER (✔), to enter the parameter:
✻ use this button to request the credit; after a few moments you will see on display the requested information.
It’s possible to define a threshold value.Each time this value is reached, the panel can send a SMS to notify
the reachment of the threshold.
MENU DAY & TIME
DAY AND TIME
With this parameter it is possible to change date and time of the system.
➣ after entering the menu, press ENTER (✔) to change
➣ press ENTER (✔) to enter the day of the week (1 for Mon, 2 for Tue..... 0 for Sun)
➣ press Right arrow to enter in sequence day / month / year / hour / minute
➣ confirm with ENTER (✔)
www.amcelettronica.com
9
C24 GSM v1.5
PLANNING AND MANAGEMENT BY SMS MESSAGES
C24 gsm can also be programmed and managed through SMS messages.Sending an SMS to the number
of dialer you can:
● program the system in its entirety (except for Contact ID)
● toggle open-collector outputs
● check the status the whole system 24 gsm può essere programmato e gestito anche tramite messaggi
SMS.
The operations carried out are divided into:
● user operation
● technical operation
USERS OPEATIONS
The user can arm / disarm the system, enable and disable (permanently or pulsed) outputs of the system,
monitor all the inputs of the dialer, check the status (on / off) of equipment external to the dialer, change the
personal code to access the voice menu, allow the installer to remotely reprogram the controller.
USE OF SMS TEXT MESSAGES FOR REMOTE PROGRAMMING
All the messages conveyed to the system must have a determined structure, otherwise programme
it would fail. Firstly they must contain a “ declaration of personal code ”.
Example: UPWD:111111 User Password , TPWD:000000 Technical Password
If the message contains one or more values for the parameters, their structure must be the following:
ID[.index] OPERATOR [value ]
ID = is the parameter identified by an alphanumeric code (example: OUT is the command needed to
change the status of an output, INMODE is the command to change Input Type).
[.index] = is the number of ID previously mentioned, therefore this is the output, input, telephone, password,
etc. number (example: INMODE.1 = INPUT 1 TYPE). Many IDs need the .index (e.g. IN.3, EXTTEL.
25, etc. ) but many do not (CPWD, LIFETEST, etc.).
Operator = this brings about a certain operation on parameter identified by ID.
: means entering, and is used for passwords (example: UPWD:111111)
= means a setting (example: OUT.1=ON switches on output 1)
? is a request of information (example: IN.1=? Asks for the input 1 status)
[value ] = indicates the commands that can be used; see the list below:
ON OFF P
O
C
B
a
b
c
= enable (outputs)
= disable (outputs)
= enable with pulse (outputs)
= normally opened (inputs)
= normally closed (inputs)
= 1K EOL (inputs)
= answer confirmation (on telephone numbers)
= direct access to user menu (on telephone numbers)
= automatic reset of the call cycle (on telephone numbers)
www.amcelettronica.com
10
C24 GSM v1.5
At each SMS text message, the system can answer with different messages as feedback:
OK *?* *LOCKED* FAIL
ON OFF OP CL command carried out
command non recognized
no user authorization
not possible to carry out the command (example: there are no privilege for its execution)
refers to the enabled status of an output
refers to the disabled status of an output
refers to the open (enabled) status of an input
refers to the closed (disabled) status of an input
ARM / DISARM THE CONTROL UNIT VIA SMS
In order to arm or disarm the system it is needed one user code of type “master”.
UPWD:111111 ALARM=T TOTAL ARMED
UPWD:111111 ALARM=1 PARTIAL1 ARMED
UPWD:111111 ALARM=2 PARTIAL2 ARMED
UPWD:111111 ALARM=3 PARTIALE3 ARMED
UPWD:111111 ALARM=- DISARMED
UPWD:111111 ALARM? SMS SYSTEM STATUS NOTIFICATION
www.amcelettronica.com
11
C24 GSM v1.5
HOW TO WRITE A PROGRAMMING SMS
To give a command through an SMS, a few simple rules must be taken into account. Programming SMS text
messages can be sent by the technician (to set system parameters) as well as by the user.
For example, if the second input needs to be associated to type EOL:
UPWD:111111 LOCK=OFF this command enables programming through SMS for 20 minutes
Now it is possible for the technician to give other commands, always preceded by the password:
TPWD:000000 INMODE.2=B this command assign type EOL to the second input.
As you see from the example, EACH COMMAND HAS TO BE SEPARATED FROM THE PREVIOUS AND
THE FOLLOWING ONE BY AT LEAST ONE SPACE AND NO SPACE HAS TO BE PRESENT IN A SINGLE
COMMAND.
It is possible to have spaces other than for separating commands only in the case they are between quotation
marks, as in the following example:
Storing of telephone number 1 (with name) and options Answer Confirmation and Automatic Reset of
the Call Cycle:
TPWD:000000 TEL.1=”MARC MOBILE +393358554574 ac”
From the example it is clear that a space has to be used between the telephone number and its options
-if there are any-, therefore if you want to store a telephone number with relative options you have to use
quotation marks.
Quotation marks are also necessary to compose a text message:
Example: programming an SMS for burglary at input 1:
TPWD:000000 SMSTEXT.1=”Burglary at apartment Mr. Brown Tel. 02564887945”
At each command the system will send one or more messages back including the results of the previous programming.
For example if you send the following programming:
TPWD:000000 INMODE.1=C INMODE.2=C INMODE.3=C VOXTEL.1=12345 VOXTEL.2=123 VOXTEL.6 =12
VOXREPEAT=3
In this example the technical password has ben entered; inputs 1, 2 and 3 have been set as NC; speech message 1
has been linked to telephone numbers 1, 2, 3, 4 and 5; speech message 2 to telephone numbers 1, 2 and 3; speech
message 6 to telephone numbers 1 and 2. At last the message repetition count has been set to 3.
The system, after reception of the programming message, will immediately answer with an SMS as the following one:
TPWD:OK
INMODE1:OK
INMODE2:OK
INMODE3:OK
VOXTEL1:OK
VOXTEL2:OK
VOXTEL6:OK
VOXREPEAT:OK
In case the system has not been enabled by the user for remote programming, it will send back the message
LOCKED.
In case the system is unable to perform a command (for example, user not authorized), will answer with FAIL.
In case the system does not recognize a message (typing errors), it will answer with ?
www.amcelettronica.com
12
C24 GSM v1.5
CALL AND PROGRAMMING WITH THE VOCAL MENU
RECEPTION OF THE VOCAL CALL
While receiving a vocal call from the system it is possible to perform several operations, depending on the programming (options) linked to the called number:
NUMBER WITH NO OPTION: once the call has been answered, the dispatch is considered successful, therefore the
system will call the following number. In case the user wants to enter programming, enter # before the dialler hangs
up and then dial the personal code.
REMARK: LISTEN AT LEAST TO THE FIRST 5 SEC. OF THE MESSAGE, OTHERWISE THE DIALLER WILL NOT
NOTIFY THIS CALL AS SUCCESSFUL AND THEREFORE WILL CALL THE SAME PHONE NUMBER AGAIN.
STOP A CALL WITH THE RESET CODE: once a call has been answered, PRESS # TO STOP THE MESSAGE AND
DIAL THE RESET CODE (example #123#), the system will respond with the message “ call cycle stopped ”.
NUMBER WITH OPTION “A” (ANSWER CONFIRMATION):
In order to make the call to the number successful it is necessary to press #; if this is not done the system will call
immediately the same number. In case the user wants to enter programming, he/she has to enter # and then dial the
personal code.
NUMBER WITH OPTION “B” (DIRECT ACCESS TO USER MENU): when the call is answered, after the message
repetition, the system switches immediately to the user menu without asking the personal code. By pressing # the
access
will be anticipated.
NUMBER WITH OPTION “C” (RESET OF THE CALL CYCLE): when the call is considered successful, the system
will reset automatically the remaining calls.
Important: when this option is activated, it is useful to activate option A as well, to be sure that the entire call
cycle can be reset only by pressing #.
NOTE: the above mentioned options can be entered for each telephone number; at each telephone number
several options can be assigned.
CALL TO THE SYSTEM
➣ If the answer is enabled, after the set number of rings, the system will accept the incoming calls, by keeping silent.
➣ Enter # and then enter the personal code. Confirm the code with #.
➣ If the code is correct the user will be introduced to the user vocal menu.
USER VOCAL MENU
The vocal menu can only be entered by calling the system, or when you are called by the system; it is not intended to
programme, but for remote operating by users (system check, output activation).
Menu 1 invites the user to arm the system.
Menu 2 contains the commands to activate outputs: it is possible to enable (in steady or pulsed mode) and
disable a single or more outputs.’
Menu 3 allow a user to check status of the inputs and SYS (enabled or open / disabled or closed) and of the
outputs (enabled / disabled) in real time: their status are therefore listed by a synthesized voice. Input SYS is intended
for real time status monitoring of remote devices, which are remotely switched by using the system outputs. It is also
possible to record two messages corresponding to activation or shutdown (example: “alarm unit on”, “alarm unit off”).
Menu 4 allow a user to connect with a remote system (example: intercom) for two-way telephone communication.
When the command is activated, ring output will be activated (for ring simulation) and, simultaneously, the automatic
voice will ask to wait. When the remote system is connected the automatic voice will tell that the connection has been
established and that the communication will start.
www.amcelettronica.com
13
C24 GSM v1.5
EVENTS LIST
The following is a list of reported events by the
system (EVENT MEMORY)
“User n° ... access by plug”
“Slave n° ... access by plug”
“Slave n° ... access”
“User n° ... access”
“DTMF User n° ... access”
“SMS user n° ... access”
“Input n° ... alarm”
“Low battery”
“Input n° ... short-circuit”
“Disarmed by plug”
“Remote disarmed”
“Disarmed by user n°...”
“DTMF disarmed”
“SMS disarmed”
“Remote input n° ... breakdown exclusion”
“Input n° ... breakdown exclusion”
“Plug n° ... breakdown exclusion”
“Keypad n° ... breakdown exclusion”
“DTMF armed partial n° ...”
“Total DTMF armed”
“Remote armed partial”
“Total remote armed”
“SMS armed partial n° ...”
“Total SMS armed”
“Armed by plug partial n° ...”
“Total armed by plug”
“Armed partial n° ...”
“Total armed “
“AC loss”
“Remote input n° ... tamper”
“Plug n° ... tamper”
“Keypad n° ... tamper”
“GSM failure”
“Programming”
“Call cycle reset”
“AC recovery”
“Re-armed by plug partial n° ...”
“Re-armed partial n° ...”
“Total re-armed by plug”
“Total re-armed”
“Input n° ... cable-cut”
“System tamper “
“Tamper line”
www.amcelettronica.com
14
C24 GSM v1.5
www.amcelettronica.com
15
C24 GSM v1.5
Our products/systems comply with the essential requirements of EEC directives. Installation must be carried out following
the local installation norms by qualified personnel.
AMC Elettronica S.r.l. refuses any responsibility when changes or unauthorized repairs are made to the product/system. It
is recommended to test the operation of the alarm product/system at least once a month. Despite frequent testing and due
to, but not limited to, any or all of the following: tampering, electrical or communication disruption or improper use, it is
possible for the product/system to fail to prevent burglary, robbery, fire or otherwise. A properly installed and maintained
alarm system can only reduce the risk that this happens.
Any GSM speech dialler or communicator, not connected to the PSTN standard telephone line, does not
ensure proper communication in case of problems or limitations due to the GSM network.
www.amcelettronica.com
16
C24 GSM v1.5