Datasheet
Transcript
Datasheet
7CMT1A DATE : 27/09/2006 REV. .0 7CMT1 (7CMT1A) AZIONAMENTO PER ATTUATORE / ACTUATOR CONTROL CARD - MANUALE D’USO – - USER’S GUIDE - A B C D E F G H I J AZIONAMENTO CMT1A PER ATTUATORE 24V CON AMPEROMETRICA E FINECORSA CMT1A : ACTUATOR CONTROL CARD WITH AMMETER PROTECTION AND END-SWITCHES ITALIANO / INGLESE VALORE / VALUE Alimentazione / Power supply 24Vac - 50/60Hz Tensione d'uscita / Output voltage 24Vdc Corrente massima motore bloccato / max current 16A Amperometrica / Ammeter protection 4 - 16A Fusibile / Input fuse 16A Relè / Relais 250Vac / 28Vdc - 14Am Dimensioni / Size 100x70x35 (mm) Dimensioni con base di fissaggio / Size with base (optional cod.8CMT1KIT) 100x95x50 (mm) Collegamento parte di potenza / Connector power faston 6.3mm Collegamento parte logica / logic connector connettori estraibili / joint connector CARATTERISTICHE / FEATURS 1 2 3 4 5 CARATTERISTICHE: La scheda Italsea CMT1A consente controllo di un attuatore A0-1 a corrente continua con gestione dell'inversione di marcia mediante relè e arresto del motore sui finecorsa o con intervento amperometrico. L'arresto dell'intervento amperometrico è tarabile con trimmer : se il motore viene bloccato in battuta meccanica a finecorsa, quando la corrente assorbita supera un valore di soglia preimpostato mediante trimmer, si ha l'arresto del movimento del motore. Per resettare l'intervento amperometrico è necessario aprire entrambi i contatti di direzione per un tempo superiore a 0.5 secondi. Per un corretto reset utilizzare due pulsanti o un deviatore a tre posizioni stabili ON/OFF/ON. 1 2 3 4 FEATURES: 7CMT1A can drive on both directions an AO-1 actuator or less , with or without mechanical endswitch. The ammeter protection acts as a protection when the actuator in moving and stops the motor when it is at the max and the min lenght. Forward and backward direction depends of two n.o. switches, that control the two directional relais. To reset the ammeter protection, you have to open both directional switch for a time not less than 0.5 sec., so you must use two switches or a 3-way selector. 5 INSTALLAZIONE: Collegare secondo lo schema. N.B. Per le direzioni di marcia utilizzare due pulsanti o un deviatore a 3 posizioni stabili (ON/OFF/ON). 6 INSTALLATION: Read the wiring diagram. D1 FINECORSA LIMIT SWITCH D2 FINECORSA LIMIT SWITCH 7 4 3 2 1 +M 0Vac FUS16A 24Vdc MOTOR OUTPUT -M CMT1.2 24Vac 50/60Hz SUPPLY 8 7 FC_I FC_D P1 P2 6 LED AMPEROMETRICA AMMETER LED LED ALIMENTAZIONE POWER ON LED 8 ROSSO / RED VERDE / GREEN 12/24Vac 1 2 AMPEROMETRICA AMMETER TRIMMER 3 9 9 FC_I FC_D P1 P2 D2 (DISABILITAZIONE FINECORSA) LIMIT SWITCH DISABLE D1 (DISABILITAZIONE FINECORSA) LIMIT SWITCH DISABLE (DISABILITAZIONE AMPEROMETRICA) AMMETER DIRECTION 2 OFF (DISABILITAZIONE AMPEROMETRICA) AMMETER DIRECTION 1 OFF D2 DIREZIONE 2 (direction 2) D1 DIREZIONE 1 (direction 1) 1 0 Modifica: data Rev. Rif. Titolo: SCHEMA COLLEGAMENTO 7CMT1A Data: Cliente: VARI 05/11/02 Codice: 7CMT1A Disegno: Filippo FAGGION A. 15/11/02 Ver.: Appr.: Nome File: 7CMT1A_6810047.SCH 1 0 Resp. 0 Questo disegno è di nostra proprietà e non può essere ceduto a terzi senza nostro preventivo consenso. A B C D E F G H I J A B C D E F G H I J AZIONAMENTO CMT1 PER ATTUATORE 24V CON FINECORSA CMT1:ACTUATOR CONTROL CARD WITH MECCHANICAL END-SWITCHES. 1 1 ITALIANO / INGLESE CARATTERISTICHE / FEATURS VALORE / VALUE Alimentazione / Power supply Tensione d'uscita / Output voltage Corrente massima motore bloccato / max current Fusibile / Input fuse Relè / Relais Dimensioni / Size Dimensioni con base di fissaggio / Size with base (optional cod.8CMT1KIT) Collegamento parte di potenza / Connector power Collegamento parte logica / logic connector 2 3 24Vac - 50/60Hz 24Vdc 16A 16A 250Vac / 28Vdc - 14Am 2 100x70x35 (mm) 100x95x50 (mm) faston 6.3mm connettori estraibili / joint connector 3 CARATTERISTICHE: La scheda Italsea CMT1 consente il controllo di un attuatore A0-1a corrente continua con gestione dell'inversione di marcia mediante relè. L'arresto dell'attuatore avviene mediante l'utilizzo di due finecorsa con contatto N.C. 4 5 4 FEATURES: 7CMT1 can drive on both directions an AO-1 actuator or less , with mechanical endswitch. The power on is show by the green led on. Forward and backward direction depends of two n.c. switches, that control the two directional relais. 5 INSTALLAZIONE: Eseguire il collegamento della scheda secondo lo schema. INSTALLATION: WARNING!!! Read the wiring diagram. 6 6 D2 D1 FINECORSA FINECORSA LIMIT SWITCH 7 LIMIT SWITCH 4 3 2 7 1 +M 0Vac FUS16A ALIMENTAZIONE 24VAC MOTORE 24VDC -M CMT1.2 24VAC SUPPLY 24Vdc MOTOR OUTPUT 8 8 12/24Vac 1 2 3 9 9 D2 - DIREZIONE 2 (direction 2) D1 - DIREZIONE 1 (direction 1) 1 0 Modifica: data Rev. Rif. 0 Titolo: SCHEMA COLLEGAMENTO 7CMT1 Data: Cliente: VARI 05/11/02 Codice: 7CMT1 Disegno: Filippo Ver.: FAGGION A. 15/11/02 Appr.: Nome File: 7CMT1_6810044.SCH 1 0 Resp. Questo disegno è di nostra proprietà e non può essere ceduto a terzi senza nostro preventivo consenso. l A B C D E F G H I J