Capitolato _ The magnetic shield must be made of a high
Transcript
Capitolato _ The magnetic shield must be made of a high
The magnetic shield must be made of a high-permeability material (MuMetal®) and built according to the following instructions and the attached technical draws. The magnetic permability μ must reach at least the value of 80000 [G/Oe] in the DC non-saturated regime. - The shield is intended to be assembled around a high-vacuum chamber mounted on a 28 mm diameter pipe. Thus it must respect the given constrains regarding dimension and geometry. The final configuration is reported in the attached ‘assembly’ file. - Four hollow half cylinders cut along the vertical plane and labelled as “bowl-part” (measures specified in Table 1). - Four hollow partial cylinders extended for 210° and labelled as “wedge-part”(measures specified in Table 2). Every wedge-layer is intended to be inserted in the corresponding bowl-layer. - The manufacturer is required to provide a functioning support for the inner shield of the nested structure as well as the spacers needed to porperly keep each layer in the correct relative position. The material used for the support must be non-magnetic (AISI stainless steel 304 or 316 ) - The shield must feature six pairs of holes passing through each layer as indicated in the attached drwas. - The total price of the four-layer cylinder set must not exceed the price of 5000 € (VAT esclude).The freight are not included in the price specified above. Lead time within eight weeks. The layers are numbered starting from the outermost. Internal wedge radius [mm] Layer 1 Layer 2 Layer 3 Layer 4 103.5 86.5 69.5 50.5 Internal bowl radius [mm] Layer 1 Layer 2 Layer 3 Layer 4 105.5 88.5 71.5 53.5 External wedge radius [mm] Internal wedge height [mm] External wedge height [mm] 105.5 315 319 88.5 280 286 71.5 249 253 53.5 212 218 Table 1: sizes of the “wedge-parts” External bowl radius [mm] Internal bowl height [mm] External bowl height [mm] 107.5 319 323 90.5 286 290 73.5 253 257 56.5 218 224 Table 2: sizes of the “bowl-parts” Thickness wedge [mm] 2 2 2 3 Thickness bowl [mm] 2 2 2 3 Lo schermo magnetico deve essere realizzato con materiale ad alta permeabilità magnetica (MuMetal®) e costruito secondo le istruzioni riportate di seguito a nei diegni tecnici allegati. La permeabilità magnentica deve raggiungere almeno il valore di 80000 [G/Oe] sotto il livello di saturazione DC. -Lo schermo sarà assemblato attorno ad una cella ad ultra-alto vuoto sorretta da un tubo di diametro pari a 28mm. Lo schermo deve quindi rispettare I limiti imposti dalle dimensioni e dalla geometria della cella. L’assemblaggio finale dello schermo dovrà essere realizzato rispettando le indicazioni riportate nel file allegato denominato ‘assembly’. - Quattro mezzi cilindri cavi tagliati lungo il piano verticale e denominati come “bowl-part” (misure specificate nella tabella 1). - Quattro cilindri parziali cavi che si estendono per 210° e denominati come “wedge-part” (misure specificate nella tabella 2). Ogni strato “wedge” dovrà essere inserito nel corrispondente strato “bowl”. - Il produttore dovrà fornire un supporto adeguato per lo strato più interno della struttura impilata così come dei distanziatori necessari per tenere nella posizione corretta ogni strato costituente lo schermo. Il materiale utilizzato per i supporti e i distanziatori dovrà essere non-magnetico (previsto l’uso di acciaio inossidabile AISI 304 o 316). - Lo schermo dovrà essere dotato di sei coppie di foro che attraversano ognuno dei quattro strati come indicato nei file allegati. -Il prezzo totale per lo schermo a quattro strati cilindrici non dovrà superare il prezzo di 5000 € (tasse escluse). Il costo di spedizione non è incluso nel prezzo sopra specificato. I tempi di consegna non devono superare le otto settimane. Gli strati sono numerati a partire dallo strato più esterno. Raggio “wedge” interno [mm] Strato 1 Strato 2 Strato 3 Strato 4 Strato 1 Strato 2 Strato 3 103.5 86.5 69.5 50.5 Raggio “wedge” esterno [mm] Altezza “wedge” interna [mm] Altezza “wedge” esterna [mm] 105.5 315 319 88.5 280 286 71.5 249 253 53.5 212 218 Tabella 1: dimensioni delle parti “wedge” Spessore “wedge” 2 2 2 3 Raggio “bowl” interno [mm] Raggio “bowl” esterno [mm] Altezza “bowl” interna [mm] Altezza “bowl” esterna [mm] Spessore “bowl” 105.5 88.5 71.5 107.5 90.5 73.5 319 286 253 323 290 257 2 2 2 Strato 4 53.5 56.5 218 224 Tabella 2: dimensioni delle parti “bowl” 3