MT SB2 01
Transcript
MT SB2 01
I MANUALE TECNICO GB TECHNICAL MANUAL F MANUEL TECHNIQUE NL TECHNISCHE FT HANDLEIDING MT SB2 01 Sistema Videocitofonico Digitale a 2 fili Digital video door entry system with 2 wires Système visiophonique numérique à 2 fils Tweedraads digitaal video-intercom systeem 02/2004 GROUP S.P.A. ITALIANO SB 07 MT SB2 01 ITALIANO Sistema Simplebus2 SOMMARIO • GENERALITÀ pag. 2 • REGOLE DI INSTALLAZIONE pag. 15 • AVVERTENZE pag. 2 • CONFIGURAZIONE DEI DISPOSITIVI pag. 18 • POSTI INTERNI VIDEO pag. 2 • NOTE DI FUNZIONAMENTO pag. 21 • POSTI INTERNI AUDIO pag. 6 • SCHEMI DI COLLEGAMENTO pag. 88 • POSTAZIONI ESTERNE pag. 7 • VARIANTI AGLI SCHEMI BASE DI COLLEGAMENTO pag. 98 • ALIMENTATORI E ACCESSORI pag. 12 1 MT SB2 01 ITALIANO GROUP S.P.A. GENERALITÀ POSTI INTERNI VIDEO Il sistema “Simplebus2” è caratterizzato da un cablaggio semplice con soli 2 fili non polarizzati in ogni tratta dell’impianto. Non si rende quindi più necessaria ne alimentazione locale ne alimentazione centralizzata tramite conduttori aggiuntivi. La tecnologia interamente a 2 fili offre quindi il vantaggio di non doversi più preoccupare del numero di conduttori da derivare dal montante principale e del tipo di posto esterno da installare. La sostituzione da posto interno citofonico a posto interno videocitofonico è immediata. Abbinato alla pulsantiera “Powercom”, caratterizzata da estrema facilità di installazione dovuta alla modularità dei suoi elementi, il sistema “Simplebus2” diventa estremamente semplice da cablare eliminado ogni possibilità di errore e riducendo drasticamente i tempi. E’ disponibile inoltre una vasta gamma di accessori per risolvere facilmente ogni esigenza di impianto. Il sistema può gestire fino a 240 utenti connettendo al MAX 3 derivati con il medesimo codice utente. Di serie è fornito di funzione apriporta, chiamata a centralino di portineria/pulsante ausiliario e autoaccensione; è inoltre possibile avere schede opzionali per esigenze particolari (es LED, pulsanti aggiunti). Per la descrizione completa degli articoli relativi all’impianto Simplebus2 fare riferimento al Catalogo 66. Istruzioni per la sicurezza Per ridurre il rischio di guasti e scosse elettriche: • non rimuovere il coperchio o effettuare personalmente riparazioni. In caso di necessità richiedere l’intervento di personale qualificato. • Non inserire oggetti ne versare liquidi all’interno del dispositivo. • Non ostacolare la circolazione dell’aria ostruendo le apposite ferritoie. Art. 4700W 4 5 6 4 1 3 9 8 7 2 1 1 AVVERTENZE Seguire scrupolosamente le istruzioni fornite dal costruttore. Tutti gli apparecchi costituenti l’impianto devono essere destinati esclusivamente all’uso per cui sono stati concepiti. COMELIT GROUP S.p.A. declina ogni responsabilità per un utilizzo improprio degli apparecchi, per modifiche effettuate da altri a qualunque titolo e scopo, per l’uso di accessori e materiali non originali. Effettuare le installazioni in conformità alle norme vigenti. Tutti i prodotti sono conformi alle prescrizioni delle direttive CEE 73/23-89/336 e ciò è attestato dalla presenza della marcatura CE sugli stessi. Evitare di porre i fili di montante in prossimità di cavi di alimentazione (220/380V). Avvertenze per l’utilizzatore In caso di guasto o malfunzionamento di una qualsiasi parte dell’impianto rivolgersi esclusivamente all’installatore o a personale qualificato. 3 2 Monitor serie Videocom da semi-incasso (tubo corto) Caratteristiche tecniche: Monitor della serie Videocom di dimensioni 193x223x65, da semi-incasso (49mm di profondità a muro), colore bianco RAL9010 con schermo B/W da 4,5” visione diretta. Può essere installato sulla scatola Art. 4514 ma anche sulle scatole da incasso per serie civili da 3 moduli DIN (Art. 4517) vedi pag. 5. Da completare con staffa Art. 4714W/2. Il monitor è completo di: 1. Ganci di fissaggio alla staffa. 2. Regolazione luminosità (ruotare per variare l’intensità). 3. Regolazione volume chiamata (spostare verso sinistra per aumentare volume). 4. Pulsante apriporta ( ). 5. Pulsante chiamata a centralino / libero (1). 6. Pulsante autoaccensione / richiesta video (2). 7. Pulsante attuatore * (3). 8. Pulsante Privacy * (4). 9. LED * (0). * disponibili solo con scheda opzionale Art. 4703W. MT SB2 01 2 MT SB2 01 Art. 4701W/A ITALIANO Art. 4700W/I 4 5 6 4 1 3 9 8 7 2 4 5 6 9 8 7 4 1 3 2 1 1 1 1 3 2 3 2 Monitor serie Videocom da semi-incasso (tubo-lungo) Monitor serie Videocom da parete Caratteristiche tecniche: Monitor della serie Videocom di dimensioni 193x223x65, da incasso (68mm di profondità a muro), colore bianco RAL9010 con schermo B/W da 4,5” visione diretta. Installabile solo sulla scatola da incasso Art. 4514 vedi pag. 5. Da completare con staffa Art. 4714W/2. Il monitor è completo di: 1. Ganci di fissaggio alla staffa. 2. Regolazione luminosità (ruotare per variare l’intensità). 3. Regolazione volume chiamata. (spostare verso sinistra per aumentare volume). 4. Pulsante apriporta ( ). 5. Pulsante chiamata a centralino / libero (1). 6. Pulsante autoaccensione / richiesta video (2). 7. Pulsante attuatore * (3). 8. Pulsante Privacy * (4). 9. LED * (0). Caratteristiche tecniche: Monitor della serie Videocom di dimensioni 193x223x65, da parete, colore bianco RAL9010 con schermo B/W da 4,5” visione diretta. Da completare con staffa Art. 4714W/2. Il monitor è completo di: 1. Ganci di fissaggio alla staffa. 2. Regolazione luminosità (ruotare per variare l’intensità). 3. Regolazione volume chiamata. (spostare verso sinistra per aumentare volume). 4. Pulsante apriporta ( ). 5. Pulsante chiamata a centralino / libero (1). 6. Pulsante autoaccensione / richiesta video (2). 7. Pulsante attuatore * (3). 8. Pulsante Privacy * (4). 9. LED * (0). * disponibili solo con scheda opzionale Art. 4703W. Art. 4514W e Art. 4517 Art. 4514 scatola incasso monitor Art. 4700W e Art. 4700W/I. Art. 4517 scatola serie civile 3 moduli DIN utilizzabile per incasso monitor Art. 4700W. * disponibili solo con scheda opzionale Art. 4703W L’utilizzo del monitor Videocom vecchia serie 4701W può causare problemi di funzionamento. Art. 4703 Scheda pulsanti supplementari e LED Scheda opzionale con 2 pulsanti supplementari e led di segnalazione. Da inserire all’interno di tutti i monitor della serie Videocom. 3 MT SB2 01 GROUP S.P.A. Installazione monitor Art. 4701W/A a parete ITALIANO Art. 4714W/2 2 7 147 cm 3 5 4 6 1 10 8 9 8 Staffa Simplebus2 Staffa di fissaggio del monitor consente l’installazione del monitor a muro o tramite base da tavolo Art. 4712W (vedi pag. 5) e permette il collegamento dei cavi di impianto. Fornita di morsetti per collegamento chiamata da piano (vedi variante G pag. 111), per la connessione di un dispositivo di ripetizione chiamata (vedi SB2/D pag. 105) e per l’utilizzo del pulsante 1 del monitor per usi vari (vedi variante E pag. 110). È possibile inserire sino a 3 staffe con lo stesso codice utente nel medesimo impianto (vedi pag. 98). Compatibile con impianti Simplebus1. 3 1 4 Caratteristiche tecniche 2 Dimensioni: 158x121x24. 1. connettore staffa monitor. 2. morsetti connessione impianto: 0 +20V morsetti connessione Art. 1212/B. L L connessione linea bus. CFP CFP ingresso chiamata da piano. P1 C1 pulsante per usi vari. Per avere un contatto pulito NO, tagliare i cavallotti CV3 e CV4. S+ Smorsetti per dispositivo ripetizione di chiamata. 3. CV5 Cavallotto chiusura video. 4. JP1 jumper di abilitazione richiesta video (vedi variante F pag. 110). 5. CN2 connettore per programmazione. 6. Dip switches per programmazione codice utente. 7. CV2, CV1, CV7 cavallotti alimentazione monitor aggiuntivo tramite Art. 1212/B (vedi variante SB2/A3 pag. 101). 8. CV3, CV4 cavallotti per liberare pulsante 1. 9. CV6 cavallotto selezione tipo di funzionamento (Simplebus2 o Simplebus1). 10. JP2 jumper selezione tipo di funzionamento (Simplebus2 o Simplebus1). MT SB2 01 4 1 3 1 4 2 2 MT SB2 01 ITALIANO Installazione base da tavolo Art. 4712W per monitor Art. 4701W/A e Art. 4700W 145 cm Installazione monitor Art. 4700W e Art. 4700W/I a parete Per monitor Art. 4700W 4700W/I Art. 4514 solo per monitor Art. 4700W Art. 4517 1 4 3 1 2 2 4 1 3 2 5 MT SB2 01 GROUP S.P.A. ITALIANO Installazione monitor semi-incasso Art. 4700W con adattatore da parete Art. 4704 147 cm 4 1 3 2 Art. 4704 Art. 4700W Come togliere il monitor POSTI INTERNI AUDIO Art. 2408W/A + C MI 5 6 3 4 + 1 2 MT SB2 01 6 Citofono Citofono della serie Okay di dimensioni 85x223x65 mm. Fornito di pulsante apriporta e di pulsante chiamata centralino utilizzabile come pulsante per usi vari negli impianti non provvisti di centralino (vedi variante A pag. 108). Equipaggiato di serie di funzione chiamata da piano (vedi variante B pag. 108). E’ possibile inserire sino a tre citofoni con lo stesso codice utente nel medesimo impianto. Per impostazione codice utente vedi “Programmazione citofono Art. 2408W/A, 2428W e staffa Art. 4714W/2” a pag. 18. Da utilizzare solo per impianti audio. Caratteristiche tecniche: 1. Pulsante apriporta. 2. Pulsante chiamata centralino/pulsante per usi vari presente in morsettiera (AB). 3. Morsetti connessione impianto: L L connessione alla linea bus. CFP CFP ingresso chiamata da piano. AB pulsante normalmente dedicato a servizi vari. Per avere contatto pulito NO tagliare i cavallotti CV1 e CV2. 4. Dip switches per impostazione codice utente (vedi pag. 19). 5. Trimmer regolazione volume microfono. 6. Trimmer regolazione volume suoneria. MT SB2 01 In impianti Simplebus2 possono essere utilizzate postazioni esterne della Serie Powercom, Vandalcom e Logicom. Per Vandalcom e Logicom rifarsi al foglio tecnico FT/SB/01 e al Catalogo 50. Portiere audio Serie Powercom Citofono Citofono come l’Art. 2408W/A con in più interruttore e Led supplementare per servizio Privacy o Dottore (apertura automatica serratura a seguito di chiamata). Vedi foglio tecnico interno all’articolo per la connessione ad impianto. Art. 2428W + MI C 5 6 4 + 3 1 Composto dagli Art. 3320 + Art. 1602. Portiere citofonico con morsettiera e doppio amplificatore, altoparlante stagno e microfono ad electret. Volume microfono ed altoparlante regolabili frontalmente sull’Art.1602 (vedi pag. 10); possibilità di regolazione anche posteriore nel caso sia montato sull’Art. 3320.Il microfono è removibile per migliorare la resa acustica (vedi pag. 10). Pulsante di chiamata in lega di alluminio con etichetta portanomi estraibile anteriormente. Completo di microprocessore e Dip switches ad 8 posizioni per la programmazione delle chiamate agli utenti. Per programmazione pulsanti vedi pag. 20. Alimentazione 12V AC (utilizzare Art. 1195). Funzione apriporta tramite switch elettronico a bordo (3A solo alternata). Dimensioni 112x89,5x40 mm. 2 Portieri video Serie Powercom Citofono Citofono della linea OKAY di dimensioni 85x223x65 mm. Fornito di pulsante apriporta e di pulsante chiamata a centralino utilizzabile per usi vari negli impianti non provvisti di centralino (vedi variante C pag. 109). Equipaggiato di serie di funzione chiamata da piano (vedi variante D pag. 109) e ripetizione chiamata (vedi SB2/D pag. 105). Citofono da impiegare in impianti misti audio-video a monte dell’Art. 4896 o in impianti audio quando si necessita di funzione ripetizione di chiamata. E’ possibile inserire sino a tre citofoni con lo stesso codice utente nel medesimo impianto. Per modalità di inserimento citofoni aggiuntivi con stesso codice utente vedi varianti SB2/A4 e SB2/A5 a pag. 102. Per impostazione codice utente vedi “Programmazione citofono Art. 2408W/A, 2428W e staffa Art. 4714W/2” a pag. 18. Caratteristiche tecniche: 1. Pulsante apriporta. 2. Pulsante chiamata centralino/pulsante per usi vari presente in morsettiera (P1 C1). 3. Morsetti connessione impianto: L L connessione alla linea bus. CFP CFP ingresso chiamata da piano. P1 C1 pulsante normalmente dedicato a servizi vari. Per avere un contatto pulito NO tagliare i cavallotti CV2 e CV3. S+ S- morsetti a cui connettere un dispositivo di ripetizione suoneria. 4. Dip switches per impostazione codice utente (vedi pag. 19). 5. Trimmer regolazione volume microfono. 6. Trimmer regolazione volume suoneria. Composto dagli Art. 3321 + Art. 4660. Telecamera orientabile ad alta sensibilità pinhole CCD 1/4” B/W. Illuminazione all’infrarosso (6 LED) . Completo di morsettiera e portiere citofonico con doppio amplificatore, altoparlante stagno e microfono ad electret. Volume microfono ed altoparlante regolabili frontalmente sull’Art.4660 (vedi pag. 10); possibilità di regolazione anche posteriore nel caso sia montato sull’Art. 3321. Il microfono è removibile per migliorare la resa acustica (vedi pag. 10). Pulsante di chiamata in lega di alluminio con etichetta portanomi estraibile anteriormente. Completo di microprocessore e Dip switches ad 8 posizioni per la programmazione delle chiamate agli utenti. Per programmazione pulsanti vedi pag. 20. Alimentazione 12V AC (utilizzare Art. 1195). Funzione apriporta tramite switch elettronico a bordo (3A solo alternata). Dimensioni 112x89,5x40 mm. 7 MT SB2 01 ITALIANO POSTAZIONI ESTERNE Art. 2410W GROUP S.P.A. Art. 3340 ITALIANO Art. 3110 Scatole da incasso Disponibili per 1, 2 e 3 moduli. Dimensioni singolo modulo 127x127x45 mm. Art. 3311 Telai portamoduli completi di cornice Realizzati in pressofusione di alluminio e rivestiti di particolari vernici resistenti in ambiente esterno. Disponibili per 1, 2 e 3 moduli nei colori Grigio, Bianco, Blu e Arancio. Dimensioni singolo modulo 125x125x15,5 mm. Modulo digitale di chiamata completo di rubrica elettronica Completo di display LCD grafico 128x64 dots, tastiera 16 pulsanti retroilluminati con LED blu. Funziona anche da chiave elettronica a codice con la possibilità di inserire sino a 250 password. È completo di modulo rubrica portanomi elettronica, che memorizza 400 nomi di utenti. Lo scorrimento dei nomi avviene agendo su due pulsanti di ricerca oppure digitando direttamente l’iniziale del nome o il codice utente. Una volta visualizzato il nome dell’utente desiderato basta premere il pulsante di chiamata. L’inserimento degli utenti avviene in modo semplice mediante programmatore Art. 1230 oppure con il software per PC Art. 1249. Dimensioni 112x180x40 mm. Art. 3342 Art. 3316 Custodie da parete Custodia in acciaio inox. Disponibile per 1, 2, 3, 4, 6 e 9 moduli. Da parete anche per ambiente esterno. Utile quando non è possibile incassare la scatola. Dimensioni singolo modulo 123x123x32,5 mm. Modulo rubrica elettronica Modulo rubrica portanomi elettronica, con display grafico 128x64 dots. Memorizza 400 nomi di utenti. Lo scorrimento dei nomi avviene agendo su due pulsanti di ricerca. Una volta visualizzato il nome dell’utente desiderato basta premere il pulsante di chiamata. L’inserimento degli utenti avviene in modo semplice mediante programmatore Art. 1230 oppure con il software per PC Art. 1249. Dimensioni: 112x89,5x40 mm. Art. 3323 Art. 3346 Moduli pulsanti di chiamata Modulo pulsanti di chiamata dotati di micro-switch e realizzati in lega di alluminio pressofuso e cromato. Led blu per illuminazione dei porta nomi estraibili frontalmente Disponibili a 4 e 6 pulsanti. Dimensioni 112x89,5x40 mm. Per programmazione pulsanti vedi pag. 20. Modulo di segnalazione di impianto occupato Completo di led blu lampeggiante per indicazione visiva dello stato di occupato. Il cartoncino trasparente è fornito neutro per inserire le scritte in tutte le lingue. Dimensioni: 112x89,5x38 mm. MT SB2 01 8 MT SB2 01 Come accostare più scatole 160 - 165 cm Altezza scatola incasso ITALIANO Istruzioni per installazione posto esterno audio e video Fissaggio del telaio su scatola da incasso Fissaggio del telaio su custodia da parete Collegamento cavetto a 4 poli Cablaggio morsettiera inserita o estratta 9 MT SB2 01 ITALIANO GROUP S.P.A. Inserimento moduli Montaggio, collegamenti e regolazioni gruppo audio-video + C MI + Posizione alternativa del microfono Montaggio /Smontaggio frontalini 3 4 2 5 1 Fissaggio cornice Montaggio/Smontaggio cartellini 1 360˚ open 2 3 MT SB2 01 close 10 rla Ca ssi Ro MT SB2 01 Collegamento cavetto a 4 poli ITALIANO Istruzioni per montaggio moduli informativi Art. 3326, Art. 3344 e Art. 3346 Inserimento modulo 10 Estrazione porta cartellino 10 Inserimento/estrazione cartellino 15 1 2 11 MT SB2 01 GROUP S.P.A. ITALIANO ALIMENTATORI E ACCESSORI Art. 1122/A Art. 1246 Trasformatore per Miscelatore-alimentatore Trasformatore 65VA. (T 1’on / 5’off). Primario 230VAC Secondario: OUT1: 36VAC 1,5A OUT2: 14VAC 1A Relè Relè 12-24V DC-AC 5A per usi generali. Direttamente comandabile dall’uscita di ripartizione chiamata della staffa Art. 4714W/2 o citofoni Art. 2428W. Dimensioni: 66x85x35 mm (4 moduli DIN). Morsetti connessione impianto: + alimentazione relè. C-NO-NC contatti relè. Il trasformatore è equipaggiato con PTC interno di protezione. Art. 1212/B Dimensioni: 107x90x60 (8 moduli DIN). Art. 1224 Alimentatore per monitor aggiuntivo Alimentatore 15VA (interm.). Ingresso: 230VAC Uscita: 0- 20VDC 700mA Il trasformatore è equipaggiato con PTC interno di protezione. Dimensioni: 87x105x65 (5 moduli DIN). Scambio Alimentazione 12VAC-20VDC. Dimensioni 66x85x35mm (4 moduli DIN). Morsetti connessione impianto: ~~* alimentazione 12VAC-20VDC. LS LS ingresso linea bus posto esterno secondario. LP LP ingresso linea bus posto esterno principale. LM LM uscita linea bus di montante. Per programmazione scambio vedi pag. 18. Art. 1214/2 e Art. 1216 Art. 1214/2 Art. 1216 Morsetto di derivazione e terminazione di linea Vedi pag. 20 per configurazione Art. 1216 a seconda del cavo utilizzato. Morsetti connessione impianto: Lin Lin: ingresso linea montante. Lout Lout: uscita linea montante. LM LM: linea montante derivata verso il monitor/citofono. + +: morsetti connessione alimentazione per compatibilità impianti Simplebus1. MT SB2 01 12 MT SB2 01 Art. 1195 ITALIANO JP1 Trasformatore Trasformatore 60VA (interm). Primario 230VAC Secondario: OUT1: 0-12V 1,5A OUT2: 0-12V 1,5A Il trasformatore è equipaggiato con fusibile interno di protezione. Dimensioni: 87x105x65 (5 moduli DIN). JP2 L’Art. 4896 deve essere alimentato tramite trasformatore Art.1246. Eseguire le operazioni di cablaggio e collegamento dell’impianto disinserendo l’alimentazione di rete. Essendo fornito di PTC di protezione dopo un cortocircuito, per riattivare togliere l’alimentazione per circa un minuto. Inserire la linea in ingresso dal posto esterno, e quindi dare alimentazione anche al modulo Miscelatore-alimentatore Art. 4896. Il dispositivo consente di alimentare al massimo un monitor ed è in grado di gestire al MAX 100 utenti. Art. 4896 Morsetti connessione impianto: 1. Lin Lin connessione alla linea proveniente dal posto esterno. Miscelatore-alimentatore Il Miscelatore-alimentatore Art. 4896 è contenuto in una scatola 12 moduli DIN. Dimensioni: 208x140x65 mm. Per poter accedere ai morsetti di collegamento togliere i coperchi laterali come in figura. 2. 0V 36V connessione ai morsetti OUT1 del trasformatore Art. 1246. 0V 14V connessione ai morsetti OUT2 del trasformatore Art. 1246. 3. L1 L1 L2 L2 L3 L3 L4 L4 uscita derivazione 1 di montante. uscita derivazione 2 di montante. uscita derivazione 3 di montante. uscita derivazione 4 di montante. 4. Jumper da impostare a seconda del numero di utenti totali connessi al Miscelatore-alimentatore Art. 4896. JP1 e JP2 in posizione 3 per impianti con utenti da 0 a 15. JP1 e JP2 in posizione 2 per impianti con utenti da 16 a 35. JP1 e JP2 in posizione 1 per impianti con utenti da 36 a 100. JP1 - JP2 1 2 4 1 3 2 3 4 13 MT SB2 01 GROUP S.P.A. Art. 4833/A Cavo comelit Simplebus2 Cavo specifico per impianti Simplebus2: è composto da due conduttori di sezione 1mm2 intrecciati di colore rosso e nero. Disponibili in matasse da 100 e 500 m. Amplificatore di linea Amplificatore per impianti video Simplebus1. Rigenera il segnale di montante relativamente alla componente video. Alimentazione: 12V AC o 20V DC. Da montare solo su tratta di impianto in ingresso ai Miscelatorialimentatori Art. 4896. Dimensioni: 66x85x35 mm (4 moduli DIN). ITALIANO Art. 4577 Morsetti connessione impianto: Lin Lin: ingresso linea montante. Lout Lout: uscita linea montante. ~+ ~-: alimentazione modulo. Art. 1254 Art. 4834/2 Rele per servizi vari Alimentazione 12VAC, 20VDC. Portata rele 10A. Questo accessorio consente: • servizio ripetizione suoneria. • servizio comando relè da posto interno in impianti sprovvisti di centralino. • servizio luci scale. • servizio apriporta secondario. Per cablaggio e spiegazione servizi si veda documentazione dell’Art. 1254. Concentratore di linea Concentratore di linea per impianto Simplebus video. Consente la distribuzione del segnale su 4 montanti. Da montare solo su tratta di impianto in ingresso ai Miscelatorialimentatori Art. 4896. Dimensioni: 66x85x35 mm (4 moduli DIN). MT SB2 01 14 Morsetti connessione impianto: Lin Lin: ingresso linea montante. L1 L1: uscita derivazione1 di montante. L2 L2: uscita derivazione2 di montante. L3 L3: uscita derivazione3 di montante (tagliare la resistenza prima di inserire i cavi). L4 L4: uscita derivazione4 di montante (tagliare la resistenza prima di inserire i cavi). MT SB2 01 Regole d’installazione per impianti videocitofonici Evitare di porre i fili di montante in prossimità di cavi di alimentazione (220/380V). Nelle diramazioni verso ogni utente inserire sul montante il morsetto Art. 1214/2 fornito a corredo della staffa Art. 4714W/2 o acquistabile separatamente per i citofoni Art. 2428W. Terminare ogni montante o diramazione con l’Art. 1216 fornito a corredo del Miscelatore-alimentatore Art. 4896 e del modulo video Art. 4660. In funzione del cavo utilizzato per il montante impostare la chiusura sull’Art. 1216 come indicato in tabella a pag. 20. In funzione del cavo utilizzato per il montante valutare la distanza massima raggiungibile tra Alimentatore-miscelatore Art. 4896 e monitor più lontano e tra morsetto di derivazione Art. 1214/2 e monitor più lontano. In funzione del cavo utilizzato per il collegamento valutare la distanza massima raggiungibile tra il posto esterno video e il Miscelatore-alimentatore Art. 4896. Riferirsi alle tabelle a pag. 16 per valutare le distanze in funzione dei conduttori. Ogni Art.4896 può gestire MAX 4 diramazioni di montante vedi variante SB2/B pag. 103. Nel caso di impianti con porte principali e secondarie (vedi schema SB2V/EN/112 pag. 97) è necessario impiegare il concentratore di linea Art. 4834/2 e lo scambio Art. 1224. Nel caso di unica porta è possibile connettere fino a 4 Miscelatori-alimentatori Art. 4896 dopo l’Art. 4834/2 (vedi schema SB2V/012 pag. 94). Ogni Art. 4834/2 consente al MAX 4 diramazioni: nel caso si necessiti di più diramazioni (fino a 16) è necessario mettere in cascata due Art. 4834/2. L’Art. 4834/2 aggiunto deve essere preceduto dal rispettivo amplificatore di segnale video Art. 4833/A (vedi variante SB2/C pag. 104). Si possono inserire sino al MAX 2 Art.4834/2 in cascata. Il numero MAX di utenti collegabili ad un singolo Miscelatorealimentatore Art. 4896 è di 100 indipendentemente che siano divisi su un singolo montante o su più diramazioni di montante (es: 100 utenti su singolo montante o 25 utenti su ognuno delle 4 diramazioni di montante.) È possibile connettere sino a 25 monitor in cascata per ogni diramazione di montante (vedi variante SB2/G pag. 106); in questo caso per determinare la distanza MAX tra posto esterno e ultimo monitor della cascata fare riferimento alla tabella di pag. 16 colonna A. Il collegamento tra più monitor con stesso codice utente (MAX 3) può avvenire in cascata o in derivazione dal montante seguendo le varianti SB2/A1-A2-A3-A4-A5 (vedi pagg. 99-100-101-102). I citofoni Art. 2428W con stesso codice utente di monitor devono essere derivati direttamente dal montante tramite Art. 1214/2. L’Art. 4896 alimenta un solo monitor per ogni chiamata, quindi per impianti con più monitor con lo stesso codice utente è necessario impostare i monitor aggiuntivi come secondari o alimentare separatamente tramite Art.1212/B ogni monitor supplementare (vedi pagg. 99-100-101). Impostare i cavallotti ed i jumper sulla staffa Art. 4714W/2 come mostrato nelle varianti agli schemi base SB2/A1-A2-A3 a seconda della configurazione che si vuole ottenere. Le telecamere dei posti esterni non devono essere rivolte verso fonti di luce diretta (es. lampade, luce solare, superfici riflettenti, ecc …) 15 MT SB2 01 ITALIANO REGOLE DI INSTALLAZIONE ITALIANO GROUP S.P.A. Distanze massime e caratteristiche dei conduttori Il collegamento degli apparecchi è di tipo non polarizzato. L’impiego di conduttori con caratteristiche diverse da quelli prescritti, non garantisce il raggiungimento di determinate distanze di impianto e la buona qualità del segnale video , per cui utilizzare esclusivamente cavi descritti nelle tabelle seguenti. Distanza MAX tra Miscelatore Art. 4896 e posto interno. Tipo di cavo Distanza MAX tra posto esterno e Miscelatore. Art. 4896 Distanza MAX tra posto esterno e Art. 4833/A. Distanza MAX tra Art. 4833/A e Miscelatore Art. 4896. Distanza MAX tra posto esterno e Miscelatore o amplifcatore Art. 4833/A con un Art. 4834/2 inserito. Distanza MAX tra morsetto di derivazione Art. 1214/2 e posto interno. A B C D E H Cavo Comelit Art. 4577 sez. 1 mm2 (Ø 1,2 mm) 200 m 200 m 200 m 200 m 150 m 60 m Cavo bifilare sez. 1,5 mm2 (Ø 1,4 mm)** 150 m 100 m 100 m 100 m 80 m 40 m Cavo intrecciato e schermato sez. 1 mm2 (Ø 1,2 mm)* 120 m 80 m 80 m 80 m 50 m 30 m Doppino telefonico twistato sez. 0,28 mm2 (Ø 0,6 mm)* 100 m 150 m 150 m 150 m 100 m 40 m Cavo UTP5 cat 5 AWG 24 sez. 0,2 mm2 (Ø 0,5 mm)* 80 m 150 m 150 m 150 m 100 m 40 m 120 m 100 m 100 m 100 m 80 m 40 m Cavo bifilare sez. 0,5 mm2 (Ø 0,8 mm)** * Nel caso si utilizzi un cavo multicoppiola usare una sola delle coppiole disponibili. Nel caso sia necessario per diminuire le cadute resistive utilizzare la singola coppiola come singolo filo. ** Nel caso si utilizzi un cavo multipolare usare solo due dei fili disponibili e non utilizzare mai fili in parallelo. Distanze massime raggiungibili per i conduttori di alimentazione monitor aggiunto e posto esterno Sezione del conduttore Distanza MAX tra trasformatore Art. 1195 e posto esterno. Distanza MAX tra alimentatore Art. 1212/B e posto interno. F G (Ø 0,6 mm) 4m 10 m 0,5 mm 2 (Ø 0,8 mm) 10 m 25 m 1 mm 2 (Ø 1,2 mm) 20 m 50 m 1,5 mm 2 (Ø 1,4 mm) 30 m 100 m 2 mm 2 (Ø 1,6 mm) 40 m 150 m 0,28 mm 2 MT SB2 01 16 MT SB2 01 ITALIANO Figure per le distanze 17 MT SB2 01 GROUP S.P.A. 1 2 3 4 5 6 7 8 Programmazione citofono Art. 2408W/A, 2410W, 2428W e staffa Art. 4714W/2 1 2 3 4 5 6 7 8 ITALIANO CONFIGURAZIONE DEI DISPOSITIVI • Ogni citofono o staffa del sistema viene identificato mediante il proprio codice; tale codice deve essere impostato mediante il Dip switches presente sulla scheda citofonica oppure sulla staffa (vedi figure). • Il codice utente deve essere impostato secondo la corrispondenza descritta nella tabella di programmazione di pag. 19. • La codifica può avvenire in qualsiasi momento, anche senza alimentazione. Programmazione scambio Art. 1224 • Esempio di codifica scambio Art. 1224 della scala A numero minimo 1, numero massimo 10. X MA N MI O1 N 2 3 4 5 6 7 O1 8 N 2 3 4 5 6 7 8 SCALA A N° 1÷10 4700 W 4700 W/I 4701 W/A 4700 W 4700 W/I 4701 W/A 4700 W 4700 W/I 4701 W/A 4700 W 4700 W/I 4701 W/A SCALA B N° 11÷20 PORTA PRINCIPALE DAL N° 1÷20. • Ogni modulo scambio è dotato di una coppia di Dip switches ad 8 selettori (vedi figura). I due Dip switches definiscono il range minimo MIN e massimo MAX di codici che possono essere riconosciuti dallo scambio. MT SB2 01 18 • Si ricordi che i Dip switches MIN e MAX definiscono rispettivamente i codici utente più basso e più alto collegabili al montante. • Per l’impostazione dei valori desiderati si faccia riferimento alla tabella di pag. 19. • Scambi distinti devono gestire intervalli di codici non sovrapposti. MT SB2 01 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 1 2 1,2 3 1,3 2,3 1,2,3 4 1,4 2,4 1,2,4 3,4 1,3,4 2,3,4 1,2,3,4 5 1,5 2,5 1,2,5 3,5 1,3,5 2,3,5 1,2,3,5 4,5 1,4,5 2,4,5 1,2,4,5 3,4,5 1,3,4,5 2,3,4,5 1,2,3,4,5 6 1,6 2,6 1,2,6 3,6 1,3,6 2,3,6 1,2,3,6 4,6 1,4,6 2,4,6 1,2,4,6 3,4,6 1,3,4,6 2,3,4,6 1,2,3,4,6 5,6 1,5,6 2,5,6 1,2,5,6 3,5,6 1,3,5,6 2,3,5,6 1,2,3,5,6 4,5,6 1,4,5,6 2,4,5,6 1,2,4,5,6 3,4,5,6 Nome utente Cod.ut. Dip switches su ON 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 1,3,4,5,6 2,3,4,5,6 1,2,3,4,5,6 7 1,7 2,7 1,2,7 3,7 1,3,7 2,3,7 1,2,3,7 4,7 1,4,7 2,4,7 1,2,4,7 3,4,7 1,3,4,7 2,3,4,7 1,2,3,4,7 5,7 1,5,7 2,5,7 1,2,5,7 3,5,7 1,3,5,7 2,3,5,7 1,2,3,5,7 4,5,7 1,4,5,7 2,4,5,7 1,2,4,5,7 3,4,5,7 1,3,4,5,7 2,3,4,5,7 1,2,3,4,5,7 6,7 1,6,7 2,6,7 1,2,6,7 3,6,7 1,3,6,7 2,3,6,7 1,2,3,6,7 4,6,7 1,4,6,7 2,4,6,7 1,2,4,6,7 3,4,6,7 1,3,4,6,7 2,3,4,6,7 1,2,3,4,6,7 5,6,7 1,5,6,7 2,5,6,7 1,2,5,6,7 3,5,6,7 1,3,5,6,7 2,3,5,6,7 1,2,3,5,6,7 4,5,6,7 Nome utente Cod.ut. Dip switches su ON 121 1,4,5,6,7 122 2,4,5,6,7 123 1,2,4,5,6,7 124 3,4,5,6,7 125 1,3,4,5,6,7 126 2,3,4,5,6,7 127 1,2,3,4,5,6,7 128 8 129 1,8 130 2,8 131 1,2,8 132 3,8 133 1,3,8 134 2,3,8 135 1,2,3,8 136 4,8 137 1,4,8 138 2,4,8 139 1,2,4,8 140 3,4,8 141 1,3,4,8 142 2,3,4,8 143 1,2,3,4,8 144 5,8 145 1,5,8 146 2,5,8 147 1,2,5,8 148 3,5,8 149 1,3,5,8 150 2,3,5,8 151 1,2,3,5,8 152 4,5,8 153 1,4,5,8 154 2,4,5,8 155 1,2,4,5,8 156 3,4,5,8 157 1,3,4,5,8 158 2,3,4,5,8 159 1,2,3,4,5,8 160 6,8 161 1,6,8 162 2,6,8 163 1,2,6,8 164 3,6,8 165 1,3,6,8 166 2,3,6,8 167 1,2,3,6,8 168 4,6,8 169 1,4,6,8 170 2,4,6,8 171 1,2,4,6,8 172 3,4,6,8 173 1,3,4,6,8 174 2,3,4,6,8 175 1,2,3,4,6,8 176 5,6,8 177 1,5,6,8 178 2,5,6,8 179 1,2,5,6,8 180 3,5,6,8 Nome utente Cod.ut. Dip switches su ON Nome utente 181 1,3,5,6,8 182 2,3,5,6,8 183 1,2,3,5,6,8 184 4,5,6,8 185 1,4,5,6,8 186 2,4,5,6,8 187 1,2,4,5,6,8 188 3,4,5,6,8 189 1,3,4,5,6,8 190 2,3,4,5,6,8 191 1,2,3,4,5,6,8 192 7,8 193 1,7,8 194 2,7,8 195 1,2,7,8 196 3,7,8 197 1,3,7,8 198 2,3,7,8 199 1,2,3,7,8 200 4,7,8 201 1,4,7,8 202 2,4,7,8 203 1,2,4,7,8 204 3,4,7,8 205 1,3,4,7,8 206 2,3,4,7,8 207 1,2,3,4,7,8 208 5,7,8 209 1,5,7,8 210 2,5,7,8 211 1,2,5,7,8 212 3,5,7,8 213 1,3,5,7,8 214 2,3,5,7,8 215 1,2,3,5,7,8 216 4,5,7,8 217 1,4,5,7,8 218 2,4,5,7,8 219 1,2,4,5,7,8 220 3,4,5,7,8 221 1,3,4,5,7,8 222 2,3,4,5,7,8 223 1,2,3,4,5,7,8 224 6,7,8 225 1,6,7,8 226 2,6,7,8 227 1,2,6,7,8 228 3,6,7,8 229 1,3,6,7,8 230 2,3,6,7,8 231 1,2,3,6,7,8 232 4,6,7,8 233 1,4,6,7,8 234 2,4,6,7,8 235 1,2,4,6,7,8 236 3,4,6,7,8 237 1,3,4,6,7,8 238 2,3,4,6,7,8 239 1,2,3,4,6,7,8 *240 5,6,7,8 *NOTA: il codice 240 è riservato per il centralino. ESEMPIO impostazione codice 200. 19 MT SB2 01 ITALIANO Tabella di programmazione dei Dip switches Cod.ut. Dip switches su ON GROUP S.P.A. Fig. 1 5 6 7 8 Fig. 3 Impostazione Art. 1216 2 Cavo bifilare sez. 1,5 mm2 (Ø 1,4 mm) 1 Cavo intrecciato e schermato sez. 1 mm2 (Ø 1,2 mm) 1 Doppino telefonico twistato sez. 0,28 mm2 (Ø 0,6 mm) Cavo UTP5 cat 5 AWG 24 sez. 0,2 mm2 (Ø 0,5 mm) 2 Cavo bifilare sez. 0,5 mm2 (Ø 0,8 mm) 2 20 4 Fig. 2 Cavo Comelit Art. 4577 sez. 1 mm2 (Ø 1,2 mm) MT SB2 01 3 Art. 3309 Tabella Impostazioni dell’Art. 1216 in funzione del tipo di cavo di connessione utilizzato Tipo di cavo 2 1. Connettere le morsettiere dei moduli Art. 3323/4 e Art. 3323/6 tra loro e con la morsettiera del gruppo Art. 4660 o Art. 1602 utilizzando gli appositi cavetti. Inserire i moduli Art. 3323/4 e Art. 3323/6 sulle relative morsettiere (figura 1). 2. Sulla morsettiera del modulo Art. 4660 o Art. 1602 collegare l’alimentazione su ~~ , connettere PR a -- e spostare P/O da OCC a V+ (figura 2) utilizzando i jumper presenti sulla morsettiera stessa. Connettere la morsettiera al modulo Art. 4660 o Art. 1602 assemblato come indicato precedentemente. (attenzione i moduli Art. 3323/4 e Art. 3323/6 da programmare devono essere già posizionati) (figura 2). NOTA: per il collegamento tra la morsettiera e il modulo Art. 4660 o Art. 1602 in fase di programmazione è possibile usare il cavetto Art. 3309 disponibile come accessorio opzionale (figura 3). 3. Impostare il Dip switches posto sul retro del modulo audio con lo stesso codice assegnato al citofono o monitor secondo la corrispondenza descritta nella tabella di programmazione a pag. 19. 4. Premere il pulsante che si desidera associare alla chiamata del citofono. L’avvenuta programmazione viene segnalata con un tono di conferma. 5. Al termine della programmazione rimettere i jumper nelle posizioni iniziali, PR su PR e P/O su OCC. Impostazione posto esterno principale o secondario I moduli Art. 4660 e Art. 1602 funzionano normalmente come posto esterno principale (segnalazione di occupato a tempo). Per impostarli come posto esterno secondario (segnalazione di occupato attiva per tutta la durata di impegno del montante) è necessario mettere tutti i Dip switches del selettore su ON. O N 1 ITALIANO Programmazione pulsanti con gruppo audio Art. 1602 e video Art.4660 e moduli Art. 3323/4 e 3323/6 MT SB2 01 • Il visitatore premendo il tasto di chiamata aziona la suoneria del posto interno. • Al posto esterno si ha un tono di avvenuta chiamata; se in impianti con più ingressi non si ode il tono di conferma chiamata, significa che un’altra conversazione è in atto verso un altro posto esterno installato sullo stesso montante. Nel caso sia installato l’Art. 3346, modulo di segnalazione impianto occupato, attendere sino allo spegnimento del modulo prima di richiamare. Nel caso sia installato l’Art. 3340 l’indicazione di impianto occupato è visualizzata sul display. • Al posto interno si entra in comunicazione sollevando il microtelefono. • Il tasto contraddistinto dal simbolo della chiave agisce sull’elettroserratura del posto esterno attivandola per circa 2 sec. • In impianti videocitofonici premendo il tasto di chiamata sul posto esterno si accendono i LED all’infrarosso (non visibile all’occhio umano) per l’illuminazione del soggetto; l’immagine rimane sul monitor per circa 90 sec. • Per regolazione volume microfono e volume suoneria dei citofoni vedi pag. 6, 7. • Per regolazione volume suoneria dei monitor vedi pag. 2, 3. • Per regolazione volumi audio sul posto esterno vedi pag. 10. • Per abilitare la funzione di Autoaccensione è necessario tener premuto il pulsante 2 per un tempo superiore a 2 sec. (vedi variante H pag. 111). All’avvenuta impostazione si ode un tono di conferma. • L’Autoaccensione del monitor (se la funzione è stata abilitata), avviene premendo il pulsante 2. Nel caso siano installati due posti esterni, premendo in successione il pulsante 2 di autoaccensione del monitor si ha la possibilità di visualizzare sul monitor l’immagine prima da uno poi dall’altro dei due posti esterni (funzione di bascula tra due ingressi). • Per variare la luminosità del monitor agire sulla rotella di regolazione posta nel lato inferiore. • Per variare il volume della suoneria di chiamata agire sull’apposito deviatore graduato collocato sul lato inferiore del monitor. • Con la scheda opzionale Art. 4703 è possibile impostare la funzione Privacy. Premendo il pulsante 4 del monitor per più di 2 sec. si accende il LED che segnala l’avvenuta impostazione del monitor in Privacy (vedi variante I pag. 112). In privacy il monitor non suona, si accende e si ha comunque la possibilità di andare in fonica con il posto esterno dopo la chiamata. • Agganciando la cornetta del posto interno si hanno a disposizione alcuni secondi per riprendere la fonica con il posto esterno. Dall’avvenuto aggancio passano alcuni secondi prima che l’immagine sparisca dal monitor. • Il monitor impostato come Principale (impostazione di fabbrica della staffa Art. 4714W/2) si accende su chiamata e su autoaccensione anche se inserito come monitor aggiunto con stesso codice utente. • Il monitor impostato come Secondario (vedi variante SB2/A1-A2) non si accende su chiamata ma si ha la possibilità di accenderlo su pressione pulsante 2 (funzione Richiesta Video). Non si ha in tal caso la possibilità di fare l’autoaccensione del monitor. Si noti la differenza tra autoaccensione cioè accensione del monitor ad impianto libero con possibilità di far basculare l’immagine tra due posti esterni e la richiesta video attiva solo dopo chiamata. • Monitor e citofoni con stesso codice utente suonano tutti contemporaneamente (indipendentemente se principali o secondari) su chiamata da posto esterno e su chiamata da piano. 21 MT SB2 01 ITALIANO NOTE DI FUNZIONAMENTO MT SB2 01 Simplebus2 System • GENERAL INFORMATION page 24 • INSTALLATION RULES page 37 • WARNINGS page 24 • CONFIGURATION OF THE DEVICES page 40 • INTERNAL VIDEO UNITS page 24 • NOTES ON OPERATION page 43 • INTERNAL TELEPHONE HANDSETS page 28 • WIRING DIAGRAMS page 88 • EXTERNAL UNITS page 29 • VARIANTS TO THE BASIC WIRING DIAGRAMS page 94 • POWER SUPPLIES AND ACCESSORIES page 34 23 MT SB2 01 ENGLISH SUMMARY ENGLISH GROUP S.P.A. GENERAL INFORMATION INTERNAL VIDEO UNITS The “Simplebus2” system is characterised by simple cabling with just 2 unpolarised wires in each stretch of the system. It is therefore no longer necessary to have either a local power supply or a centralised power supply by means of additional conductors. The entirely 2 wire-technology therefore offers the advantage of no longer having to worry about the number of conductors to be branched from the main riser and the type of external unit to be installed. The conversion from internal telephone unit to internal video-telephone unit is immediate. Combined with the “Powercom” entrance panel, characterised by absolute simplicity of installation thanks to the modularity of its elements, the “Simplebus2” system becomes extremely easy to cable, eliminating the possibility of errors and drastically reducing installation times. A vast range of accessories is also available to solve all system requirements easily. The system can manage up to 240 users, connecting a MAX of 3 branches with the same user code. The standard system is fitted with the door-opening function, call to porter switchboard/ auxiliary push-button and self-ignition. It is also possible to have optional card s for special needs (e.g. additional LEDs and push-buttons). For the full description of the articles regarding the Simplebus2 system, please refer to Catalogue 66. Safety Instructions To reduce the risk of faults and electric shocks: • do not remove the cover or personally carry out any repairs. If this is required, seek the intervention of qualified personnel only. • Do not insert any objects or let any liquids get inside the device. • Do not block circulation of air by obstructing the special vents. Art. 4700W 4 5 6 4 1 3 9 8 7 2 1 1 WARNINGS Strictly follow the instructions supplied by the manufacturer. All the pieces of apparatus making up the system must only be used for the purpose they were designed for. COMELIT GROUP S.p.A. declines any responsibility for incorrect use of the apparatus, for modifications made by third parties for any reason and purpose, for the use of accessories and materials which are not originals. Carry out installation in compliance with the standards in force. All the products conform to the prescriptions of the EEC 73/2389/336 Directives and this is certified by the CE mark on them. Avoid placing the riser wires near power supply cables (220/380V). Warnings for the user In the case of a fault or malfunction of any part of the system, only contact the approved installer or qualified personnel. 3 2 Videocom series semi flush-mounted Monitor (short tube) Technical characteristics: Videocom series monitor with dimensions: 193x223x65, semi flush-mounted (49 mm of depth on wall), and white RAL9010 with 4.5” direct vision B/W screen. Can be installed on the box Art. 4514, but also on the 3 DIN module civil series flush-mounting boxes (Art. 4517) - see page 27. To be completed with bracket Art. 4714W/2. The monitor is complete with: 1. Hooks for fixing to the bracket. 2. Brightness control (turn to vary the brightness). 3. Call tone volume control (move left to increase the volume). 4. Door-opening push-button ( ). 5. Push-button to call a switchboard / free contact (1). 6. Push-button self-ignition / video request (2). 7. Push-button actuator * (3). 8. Push-button Privacy * (4). 9. LED * (0). * only available with optional card Art. 4703W. MT SB2 01 24 MT SB2 01 4 5 6 4 1 3 Art. 4701W/A 9 8 7 2 4 5 6 9 8 7 4 1 3 2 1 1 ENGLISH Art. 4700W/I 1 1 3 2 3 2 Videocom series semi flush-mounted Monitor (long tube) Videocom series surface-mounted Monitor Technical characteristics: Videocom series monitor with dimensions: 193x223x65, flush-mounted (68mm of depth on wall), white RAL9010 with 4.5” direct vision B/W screen. Can only be installed on the flush-mounting box Art. 4514 - see page 27. To be completed with bracket Art. 4714W/2. The monitor is complete with: 1. Hooks for fixing to the bracket. 2. Brightness control (turn to vary the brightness). 3. Call tone volume control. (move left to increase the volume). 4. Door-opening push-button ( ). 5. Push-button to call a switchboard / free contact (1). 6. Push-button self-ignition / video request (2). 7. Push-button actuator * (3). 8. Push-button Privacy * (4). 9. LED * (0). Technical characteristics: Videocom series monitor with dimensions: 193x223x65, surface-mounted, white RAL9010, with 4.5” direct vision B/W screen. To be completed with bracket Art. 4714W/2. The monitor is complete with: 1. Hooks for fixing to the bracket. 2. Brightness control (turn to vary the brightness). 3. Call tone volume control. (move left to increase the volume). 4. Door-opening push-button ( ). 5. Push-button to call a switchboard / free contact (1). 6. Push-button self-ignition / video request (2). 7. Push-button actuator * (3). 8. Push-button Privacy * (4). 9. LED * (0). * only available with optional card Art. 4703W. * only available with optional card Art. 4703W Use of the old Videocom series 4701W monitor may cause operating problems. Art. 4514W and Art. 4517 Art. 4703 Art. 4514 flush-mounted box for monitor Art. 4700W and Art. 4700W/I. Art. 4517 3 DIN module civil series box usable for flush-mounting monitor Art. 4700W. Additional push-button and LED card Optional card with 2 additional push-buttons and signalling LED. To be inserted inside all the Videocom series monitors. 25 MT SB2 01 GROUP S.P.A. Installation of surface-mounted monitor Art. 4701W/A Art. 4714W/2 7 3 147 cm ENGLISH 2 5 4 6 1 10 8 9 8 Simplebus2 Bracket Bracket for fixing the monitor - allows installation of the monitor to the wall or by means of desk convertion kit Art. 4712W (see page 27), and permits connection of the system cables. Provided with terminals for connection of local floor call (see variant G page 111), for connection of a call repetition device (see SB2/D on page 105) and for use of push-button 1 of the monitor for various uses (see variant E on page 110). Up to 3 brackets with the same user code can be inserted in the same system (see page 98). Compatible with Simplebus1 systems. 3 1 4 Technical characteristics 2 Dimensions: 158x121x24. 1. monitor connector bracket. 2. system connection terminals: 0 +20V connection terminals Art. 1212/B. L L bus line connection. CFP CFP local floor call input. P1 C1 push-button for various uses. To have a clean NO contact, cut the CV3 and CV4 bridges. S+ Sterminals for call repeater device. 3. CV5 Bridge for closing video. 4. JP1 jumper for enabling video request (see variant F on page 110). 5. CN2 connector for programming. 6. Dip switches for programming user code. 7. CV1, CV2, and CV7 additional monitor power supply bridges by means of Art. 1212/B (see variant SB2/A3 on page 101). 8. CV3, CV4 bridges to free push-button 1. 9. CV6 bridge for selection of type of operation (Simplebus2 or Simplebus1). 10. JP2 jumper selection of type of operation (Simplebus2 or Simplebus1). MT SB2 01 26 1 3 1 4 2 2 MT SB2 01 Installation of desk convertion kit Art. 4712W for monitor Art. 4701W/A and Art. 4700W 145 cm ENGLISH Installation of surface-mounted monitor Art. 4700W and Art. 4700W/I For monitor Per monitor Art. Art. 4700W 4700W 4700W/I 4700W/I Art. 4514 solo onlyper for monitor Art. Art.4700W 4700W Art. 4517 1 4 3 1 2 2 4 1 3 2 27 MT SB2 01 GROUP S.P.A. ENGLISH Installation of semi flush-mounted monitor Art. 4700W with surface-mounting adapter Art. 4704 147 cm 4 1 3 2 Art. 4704 Art. 4700W How to remove the monitor INTERNAL TELEPHONE HANDSETS Art. 2408W/A + C MI 5 6 3 4 + 1 2 MT SB2 01 28 Telephone Okay series telephone with dimensions: 85x223x65 mm. Fitted with door-opening push-button and with switchboard call pushbutton, usable as push-button for various uses in the systems not provided with a switchboard (see variant A on page 108). Equipped as standard with the local floor call function (see variant B on page 108). Up to three telephones with the same user code can be inserted in the same system. To set the user code, see “Programming telephone Art. 2408W/A, 2428W and bracket Art. 4714W/2” on page 40. Only to be used for audio systems. Technical characteristics: 1. Door-opening push-button. 2. Switchboard call push-button/push-button for various uses present in terminal board (AB). 3. Terminal connection System with L L connection to the line bus. CFP CFP input floor door call. AB push-button normally dedicated to various services. To have a clean NO contact, cut bridges CV1 and CV2. 4. Dip switches for setting user code (see page 40). 5. Microphone volume adjustment trimmer. 6. Call tone volume adjustment trimmer. MT SB2 01 EXTERNAL UNITS Art. 2410W In Simplebus2 systems, external units of the Powercom, Vandalcom and Logicom Series can be used. For Vandalcom and Logicom, refer to technical sheet FT/SB/01 and to Catalogue 50. Powercom Series speaker unit ENGLISH Telephone Telephone like Art. 2408W/A with additional switch and LED Privacy or Doctor facility (automatic lock opening following the call). See the technical sheet inside the article for the connection to the system. Art. 2428W + MI C 5 6 4 + 3 1 Consisting of Art. 3320 + Art. 1602. Speaker unit with terminal board and double amplifier, watertight loudspeaker and electret microphone. Microphone and loudspeaker volume adjustable from the front on Art.1602 (see page 32); possibility of rear adjustment as well in the case where it is mounted on Art. 3320. The microphone can be removed to improve the acoustic output (see page 32). Aluminium alloy call button with name label extractable from the front. Complete with microprocessor and Dip switches with 8 positions for programming the calls to the users. For push-button programming, see page 42. 12V AC power supply (use Art. 1195). Door-opening function by means of an electric switch (3A only AC). Dimensions: 112x89.5x40 mm. 2 Powercom Series video speaker unit Telephone Telephone in the OKAY line with dimensions: 85x223x65 mm. Fitted with door-opening push-button and switchboard call push-button, to be used for various purposes in the systems not provided with a switchboard (see variant C on page 109). Equipped as standard with local floor call function (see variant D on page 109) and call repetition (see SB2/D on page 105). Telephone to be used in mixed audio-video systems upstream of Art. 4896 or in audio systems when the call repeat function is required. Up to three telephones with the same user code can be inserted in the same system. For methods of inserting additional telephones with the same user code, see variants SB2/A4 and SB2/A5 on page 102. To set user code, see “Programming telephone Art. 2408W/A, 2428W and bracket Art. 4714W/2” on page 40. Technical characteristics: 1. Door-opening push-button. 2. Switchboard call push-button/push-button for various uses present in the terminal board (P1 C1). 3. Terminal connection System with L L connection to the line bus. CFP CFP local floor call input. P1 C1 push-button normally dedicated to various services. To have a clean NO contact, cut bridges CV2 and CV3. S+ S- terminals to connect a bell repetition device to. 4. Dip switches for setting user code (see page 40). 5. Microphone volume adjustment trimmer. 6. Call tone volume adjustment trimmer. Consisting of Art. 3321 + Art. 4660. 1/4” pin-hole CCD B/W high sensitivity adjustable camera. Infrared illumination (6 LEDs) . Complete with terminal board and speaker unit with double amplifier, watertight loudspeaker and electret microphone. Microphone and loudspeaker volume adjustable from the front on Art.4660 (see page 32). Possibility of rear adjustment as well in the case where it is mounted on Art. 3321. The microphone can be removed to improve the acoustic output (see page 32). Aluminium alloy call button with name label extractable from the front. Complete with microprocessor and Dip switches with 8 positions for programming the calls to the users. For push-button programming, see page 42. 12V AC power supply (use Art. 1195). Door-opening function by means of electronic switch on board (3A only alternating). Dimensions: 112x89.5x40 mm. 29 MT SB2 01 GROUP S.P.A. ENGLISH Art. 3110 Art. 3340 Flush-mounting boxes Available for 1, 2 and 3 modules. Single module dimensions: 127x127x45 mm. Art. 3311 Module holder frames complete with cornice Made of die-cast aluminium and painted using special coatings to resist at outdoor environments. Available for 1, 2 and 3 modules in the Grey, White, Blue and Orange. Single module dimensions: 125x125x15.5 mm. Digital call module complete with electronic directory Complete with graphic LCD 128x64 dots, keypad with 16 push-buttons illuminated from the rear with blue LED. Also operates with electronic code key with the possibility of entering up to 250 passwords. It is complete with electronic name directory, which memorises 400 user names. Name scrolling is carried by using two search push-buttons or by entering the initials of the name or user code directly. Once the desired user name is displayed, simply press the call push-button. User programming is carried out in a simple way using programmer art. 1230 or with the software for PC art. 1249 Dimensions: 112x180x40 mm. Art. 3342 Art. 3316 Surface-mounted housings Stainless steel housing. Available for 1, 2, 3, 4, 6 and 9 modules. Surface-mounted. Useful when it is not possible to flush-mount the box. Single module dimensions: 123x123x32.5 mm. Art. 3323 Call push-button modules Call push-button module fitted with micro-switch and made of diecast and chromed aluminium alloy. Blue LEDs for illumination of the nameplate labels removable from the front. Available with 4 and 6 push-buttons. Dimensions: 112x89.5x40 mm. For push-button programming, see page 42. MT SB2 01 30 Electronic directory module Electronic name directory, with graphic display 128x64 dots. Memorises 400 user names. Name scrolling is carried out by using two search push-buttons. Once the desired user name is displayed, simply press the call push-button. User programming is carried out in a simple way using programmer art. 1230 or with the software for PC art. 1249. Dimensions: 112x89.5x40 mm. Art. 3346 System engaged signalling module Complete with flashing blue LED for visual indication of the engaged state. The transparent label is provided blanck to insert the correct wording. Dimensions: 112x89.5x38 mm. MT SB2 01 Instructions for installing external audio and video unit ENGLISH How to place several boxes together 160 - 165 cm Height of flush-mounted box Fixing the frame onto the flush-mounting box Fixing the frame onto the surface-mounted housing Connection of 4-pole cable Cabling terminal board inserted or withdrawn 31 MT SB2 01 GROUP S.P.A. Insertion of modules ENGLISH Audio-video Group Assembly, connections and adjustments + C MI + Alternative position of the microphone Assembly/Dismantling faces 3 4 2 5 1 Fixing the cornice Assembly /Dismantling labels 1 360˚ open 2 3 MT SB2 01 close 32 rla Ca ssi Ro MT SB2 01 Instructions for assembly of information modules Art. 3326, Art. 3344 and Art. 3346 Insertion of module ENGLISH Connection of 4-pole cable 10 Withdrawal of label holder 10 Insertion/withdrawal of label 15 1 2 33 MT SB2 01 GROUP S.P.A. POWER SUPPLIES AND ACCESSORIES Art. 1122/A ENGLISH Art. 1246 Transformer for Mixer-power supply 65VA Transformer. (T 1 min. on / 5 min. off). Primary: 230VAC Secondary: OUT1: 36VAC 1.5A OUT2: 14VAC 1A Relay 12-24V DC-AC 5A relay for general uses. Can be controlled directly from the call repetition output of bracket Art. 4714W/2 or telephones Art. 2428W. Dimensions: 66x85x35 mm (4 DIN modules). Terminals for system connection: + power supply relay. C-NO-NC relay contacts. The transformer is equipped with internal protection PTC. Art. 1212/B Dimensions: 107x90x60 (8 DIN modules). Art. 1224 Switching device Power supply 12VAC-20VDC. Dimensions: 66x85x35mm (4 DIN modules). Terminals for system connection: ~~* 12VAC-20VDC power supply. LS LS secondary external unit bus line input. LP LP main external unit bus line input. LM LM riser bus line output. For programming switching device, see page 40. Power supply for additional monitor Power supply 15VA (interm.). Input: 230VAC Output: 0- 20VDC 700mA The transformer is equipped with internal protection PTC. Dimensions: 87x105x65 (5 DIN modules). Art. 1214/2 and Art. 1216 Art. 1214/2 Art. 1216 Line branch and termination terminal See page 42 for configuration of Art. 1216 according to the cable used. Terminals for system connection: Lin Lin: riser line input. Lout Lout: riser line output. LM LM: riser line branched towards the monitor/telephone. + +: power supply connection terminals for compatibility with Simplebus1 systems. MT SB2 01 34 MT SB2 01 Art. 1195 ENGLISH JP1 Transformer Transformer 60VA (interm). Primary 230VAC Secondary: OUT1: 0-12V 1.5A OUT2: 0-12V 1.5A The transformer is equipped with internal protection fuse. Dimensions: 87x105x65 (5 DIN modules). JP2 Art. 4896 must be supplied by means of transformer Art.1246. Carry out the cabling and system connection prior to the connection of the power supply operations after disconnecting the mains supply. This unit is fitted with a protection PTC, device after a short-circuit, d0sconnect the power supply for approximately one minute to allow re-setting. Insert the line on input from the external unit, and then switch on the power from Art. 1246 to the Mixer-power supply module Art. 4896. The device allows a maximum of one monitor to be supplied and is able to manage a MAX of 100 users. Art. 4896 Terminals for system connection: 1. Lin Lin connection to the line coming from the external unit. Mixer-power supply The Mixer-power supply Art. 4896 is contained in a 12 DIN module box. Dimensions: 208x140x65 mm. To access the connection terminals, remove the side covers as shown in the figure. 2. 0V 36V connection to terminals OUT1 of transformer Art. 1246. 0V 14V connection to terminals OUT2 of transformer Art. 1246. 3. L1 L1 L2 L2 L3 L3 L4 L4 branch output 1 of riser. branch output 2 of riser. branch output 3 of riser. branch output 4 of riser. 4. Jumpers to be set according to the number of total users connected to the Mixer-power supply Art. 4896. JP1 and JP2 in position 3 for systems with from 0 to 15 users. JP1 and JP2 in position 2 for systems with from 16 to 35 users. JP1 and JP2 in position 1 for systems with from 36 to 100 users. JP1 - JP2 1 2 4 1 3 2 3 4 35 MT SB2 01 ENGLISH GROUP S.P.A. Art. 4577 Art. 4833/A Simplebus2 Comelit Cable Specific cable for Simplebus 2 systems: consists of two twisted red and black conductors with 1mm2 cross-section. Available in 100 and 500 m. coils. Line amplifier Amplifier for Simplebus video systems. This regenerates the riser signal in relation to the video component. Power supply: 12V AC or 20V DC. Only to be mounted on the input stretch of the system to the Mixers-power supplies Art. 4896. Dimensions: 66x85x35 mm (4 DIN modules). Terminals for system connection: Lin Lin: riser line input. Lout Lout: riser line output. ~+ ~-: power supply module. Art. 1254 Art. 4834/2 Relay for various services Power supply 12VAC, 20VDC. Relay capacity: 10A. This accessory allows: • bell repetition service. • Relay control service from internal unit in systems without switchboard. • stair lights service. • secondary door-opening service. For cabling and explanation of services, please see the Art. 1254 documentation. Line concentrator Line concentrator for Simplebus video system. Allows distribution of the signal over 4 risers. Only to be mounted on the input stretch of the system to the Mixers-power supplies Art. 4896. Dimensions: 66x85x35 mm (4 DIN modules). MT SB2 01 36 Terminals for system connection: Lin Lin: riser line input. L1 L1: branch output1 of riser. L2 L2: branch output2 of riser. L3 L3: branch output3 of riser (cut the resistance before inserting the cables). L4 L4: branch output4 of riser (cut the resistance before inserting the cables). MT SB2 01 Installation rules for video door entry systems Avoid placing the riser wires near power supply cables (220/380V). In the branches towards each user, insert terminal Art. 1214/2 supplied to equip the bracket Art. 4714W/2 or which can be purchased separately for the telephones Art. 2428W on the riser. Terminate each riser or branch with Art. 1216 supplied with the Mixer-power supply Art. 4896 and with the video module Art. 4660. According to the cable used for the riser, set closure on Art. 1216 as shown in the table on page 42. According to the cable used for the riser, assess the maximum distance which can be reached between the Mixer-Power supply Art.4896 and the monitor furthest away, and between terminal of branch terminal Art. 1214/2 and the monitor furthest away. According to the cable used for the connection, assess the maximum distance which can be reached between the external unit video and the Mixer-power supply Art. 4896. Refer to the tables on page 38 to assess the distances according to the conductors. Each Art.4896 can manage a MAX of 4 riser branches - see variant SB2/B on page 103. In the case of systems with main and secondary entrances (see diagram SB2V/EN/112 on page 97), it is necessary to use the line concentrator Art. 4834/2 and the switching device Art. 1224. In the case of a single entrance, it is possible to connect up to 4 Mixers-power supplies Art. 4896 after Art. 4834/2 (see diagram SB2V/012 on page 94). Each Art. 4834/2 allows a MAX of 4 branches: in the case where several branches are needed (up to 16), it is necessary to put two Arts. 4834/2 in cascade. The additional Art. 4834/2 must be preceded by the relative video signal amplifier Art. 4833/A (see variant SB2/C on page 104). A MAX of 2 Arts. 4834/2 in cascade can be inserted. The MAX number of users which can be connected to a single Mixer-power supply Art. 4896 is 100 regardless of whether they are divided over a single riser or over several riser branches (e.g.: 100 users over a single riser or 25 users over each of the 4 riser branches.) It is possible to connect up to 25 monitors in cascade for each riser branch (see variant SB2/G on page 106). In this case, in order to determine the Max. distance between external unit and the last monitor of the cascade, please refer to the table on page 38 column A. The connection between several monitors with same user code (MAX 3) can take place in cascade or branched from the riser following the variants SB2/A1-A2-A3-A4-A5 (pages 99-100-101-102). Telephones Art. 2428W with same monitor user code must be branched directly from the riser by means of Art. 1214/2. Art. 4896 supplies only a single monitor for each call, therefore for systems with several monitors with the same user code, it is necessary to set the additional monitors as secondary or supply each additional monitor with power separately by means of Art.1212/B (see pages 99-100-101). Set the bridges and the jumper on bracket Art. 4714W/2 as shown in the variants to the basic diagrams SB2/A1-A2-A3 according to the configuration to be obtained. The cameras of the external units must not be directed towards direct light sources (e.g.. lamps, sunlight, reflecting surfaces, etc.). 37 MT SB2 01 ENGLISH INSTALLATION RULES GROUP S.P.A. Maximum distances and characteristics of the conductors The connection of the apparatus is of the unpolarised type. The use of conductors with characteristics other than those prescribed does not guarantee certain system distances being reached or the good quality of the video signal, therefore only use the cables described in the tables below. Max. distance between Mixer Art. 4896 and internal unit. ENGLISH Type of cable Max. distance between external unit and Mixer Art. 4896 Max. distance between external unit and Art. 4833/A. Max. distance between Art. 4833/A and Mixer Art. 4896. Max. distance between external unit and Mixer or amplifier Art. 4833/A with a Art. 4834/2 inserted. Max. distance between terminal of branch Art. 1214/2 and internal unit. A B C D E H Comelit cable Art. 4577 1 mm2 cross-sect. (Ø 1.2 mm) 200 m 200 m 200 m 200 m 150 m 60 m Two-wire cable 1.5 mm2 cross-sect. (Ø 1.4 mm)** 150 m 100 m 100 m 100 m 80 m 40 m Braided and shielded cable 1 mm2 cross-sect. (Ø 1.2 mm)* 120 m 80 m 80 m 80 m 50 m 30 m Twisted telephone cable 0.28 mm2 cross-sect. (Ø 0.6 mm)* 100 m 150 m 150 m 150 m 100 m 40 m UTP5 cat 5 AWG 24 Cable 0.2 mm2 crosssect. (Ø 0.5 mm)* 80 m 150 m 150 m 150 m 100 m 40 m Two-wire cable 0.5 mm2 cross-sect. (Ø 0.8 mm)** 120 m 100 m 100 m 100 m 80 m 40 m * In case of multipaired cable, it is advisable to use one pair only for the system. If necessary to reduce voltage drop, due to long distances, it is possible to use a pair as a single core. ** In case of multicore cable, it is necessary to use only two of the available wires. We recommend not to double up on the conductors. Maximum distances which can be reached by the conductors off additional monitor power supply and external unit power supply Cross-section of the conductor Max. distance between transformer Art. 1195 and external unit. Max. distance between power supply Art. 1212/B and internal unit. F G (Ø 0.6 mm) 4m 10 m 0.5 mm 2 (Ø 0.8 mm) 10 m 25 m 1 mm 2 (Ø 1.2 mm) 20 m 50 m 1.5 mm 2 (Ø 1.4 mm) 30 m 100 m 2 mm 2 (Ø 1.6 mm) 40 m 150 m 0.28 mm 2 MT SB2 01 38 MT SB2 01 ENGLISH Figures showing distances 39 MT SB2 01 GROUP S.P.A. CONFIGURATION OF THE DEVICES 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 ENGLISH Programming telephone Art. 2408W/A, 2410W, 2428W and bracket Art. 4714W/2 • Each telephone or bracket in the system is identified by means of its own code. This code must be set by means of the Dip switches on the telephone card or on the bracket (see figures). • The user code must be set according to the corresponding one described in the programming table on page 41. • Coding can take place at any time, even without a power supply. Programming switching device Art. 1224 • Example of coding switching device Art. 1224 of staircase A minimum number: 1, maximum number: 10. X MA N MI O1 N 2 3 4 5 6 7 O1 8 N 2 3 4 5 6 7 8 STAIRCASE A SCALA A N° 1÷10 1÷10. N° 4700 W 4700 W/I 4701 W/A 4700 W 4700 W/I 4701 W/A 4700 W 4700 W/I 4701 W/A 4700 W 4700 W/I 4701 W/A STAIRCASE B SCALA B N° N° 11÷20. 11÷20 MAIN FROM PORTAENTRANCE PRINCIPALE DAL N° N° 1÷20. 1÷20. • Each switching device module is fitted with a pair of Dip switches with 8 selectors (see figure). The two Dip switches define the minimum and maximum range - MIN - MAX - of codes which can be recognised by the switching device. MT SB2 01 40 • Remember that the MIN and MAX Dip switches define the lowest and highest user codes respectively which can be connected to the riser. • For setting the values desired, refer to the table on page 41. • Distinct switching devices must manage code ranges which are not overlapping. MT SB2 01 Table for programming the Dip switches Dip switches to ON 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 1 2 1,2 3 1,3 2,3 1,2,3 4 1,4 2,4 1,2,4 3,4 1,3,4 2,3,4 1,2,3,4 5 1,5 2,5 1,2,5 3,5 1,3,5 2,3,5 1,2,3,5 4,5 1,4,5 2,4,5 1,2,4,5 3,4,5 1,3,4,5 2,3,4,5 1,2,3,4,5 6 1,6 2,6 1,2,6 3,6 1,3,6 2,3,6 1,2,3,6 4,6 1,4,6 2,4,6 1,2,4,6 3,4,6 1,3,4,6 2,3,4,6 1,2,3,4,6 5,6 1,5,6 2,5,6 1,2,5,6 3,5,6 1,3,5,6 2,3,5,6 1,2,3,5,6 4,5,6 1,4,5,6 2,4,5,6 1,2,4,5,6 3,4,5,6 User name User code Dip switches to ON 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 1,3,4,5,6 2,3,4,5,6 1,2,3,4,5,6 7 1,7 2,7 1,2,7 3,7 1,3,7 2,3,7 1,2,3,7 4,7 1,4,7 2,4,7 1,2,4,7 3,4,7 1,3,4,7 2,3,4,7 1,2,3,4,7 5,7 1,5,7 2,5,7 1,2,5,7 3,5,7 1,3,5,7 2,3,5,7 1,2,3,5,7 4,5,7 1,4,5,7 2,4,5,7 1,2,4,5,7 3,4,5,7 1,3,4,5,7 2,3,4,5,7 1,2,3,4,5,7 6,7 1,6,7 2,6,7 1,2,6,7 3,6,7 1,3,6,7 2,3,6,7 1,2,3,6,7 4,6,7 1,4,6,7 2,4,6,7 1,2,4,6,7 3,4,6,7 1,3,4,6,7 2,3,4,6,7 1,2,3,4,6,7 5,6,7 1,5,6,7 2,5,6,7 1,2,5,6,7 3,5,6,7 1,3,5,6,7 2,3,5,6,7 1,2,3,5,6,7 4,5,6,7 User name User code Dip switches to ON 121 1,4,5,6,7 122 2,4,5,6,7 123 1,2,4,5,6,7 124 3,4,5,6,7 125 1,3,4,5,6,7 126 2,3,4,5,6,7 127 1,2,3,4,5,6,7 128 8 129 1,8 130 2,8 131 1,2,8 132 3,8 133 1,3,8 134 2,3,8 135 1,2,3,8 136 4,8 137 1,4,8 138 2,4,8 139 1,2,4,8 140 3,4,8 141 1,3,4,8 142 2,3,4,8 143 1,2,3,4,8 144 5,8 145 1,5,8 146 2,5,8 147 1,2,5,8 148 3,5,8 149 1,3,5,8 150 2,3,5,8 151 1,2,3,5,8 152 4,5,8 153 1,4,5,8 154 2,4,5,8 155 1,2,4,5,8 156 3,4,5,8 157 1,3,4,5,8 158 2,3,4,5,8 159 1,2,3,4,5,8 160 6,8 161 1,6,8 162 2,6,8 163 1,2,6,8 164 3,6,8 165 1,3,6,8 166 2,3,6,8 167 1,2,3,6,8 168 4,6,8 169 1,4,6,8 170 2,4,6,8 171 1,2,4,6,8 172 3,4,6,8 173 1,3,4,6,8 174 2,3,4,6,8 175 1,2,3,4,6,8 176 5,6,8 177 1,5,6,8 178 2,5,6,8 179 1,2,5,6,8 180 3,5,6,8 User name User code Dip switches to ON User name 181 1,3,5,6,8 182 2,3,5,6,8 183 1,2,3,5,6,8 184 4,5,6,8 185 1,4,5,6,8 186 2,4,5,6,8 187 1,2,4,5,6,8 188 3,4,5,6,8 189 1,3,4,5,6,8 190 2,3,4,5,6,8 191 1,2,3,4,5,6,8 192 7,8 193 1,7,8 194 2,7,8 195 1,2,7,8 196 3,7,8 197 1,3,7,8 198 2,3,7,8 199 1,2,3,7,8 200 4,7,8 201 1,4,7,8 202 2,4,7,8 203 1,2,4,7,8 204 3,4,7,8 205 1,3,4,7,8 206 2,3,4,7,8 207 1,2,3,4,7,8 208 5,7,8 209 1,5,7,8 210 2,5,7,8 211 1,2,5,7,8 212 3,5,7,8 213 1,3,5,7,8 214 2,3,5,7,8 215 1,2,3,5,7,8 216 4,5,7,8 217 1,4,5,7,8 218 2,4,5,7,8 219 1,2,4,5,7,8 220 3,4,5,7,8 221 1,3,4,5,7,8 222 2,3,4,5,7,8 223 1,2,3,4,5,7,8 224 6,7,8 225 1,6,7,8 226 2,6,7,8 227 1,2,6,7,8 228 3,6,7,8 229 1,3,6,7,8 230 2,3,6,7,8 231 1,2,3,6,7,8 232 4,6,7,8 233 1,4,6,7,8 234 2,4,6,7,8 235 1,2,4,6,7,8 236 3,4,6,7,8 237 1,3,4,6,7,8 238 2,3,4,6,7,8 239 1,2,3,4,6,7,8 *240 5,6,7,8 ENGLISH User code *NOTE: code 240 is reserved for the switchboard. EXAMPLE: setting code 200. 41 MT SB2 01 GROUP S.P.A. Figure 1 6 7 8 2 Two-wire cable 1.5 mm2 cross-sect. (Ø 1.4 mm) 1 1 Twisted telephone cable 0.28 mm2 cross-sect. (Ø 0.6 mm) UTP5 cat 5 AWG 24 cable 0.2 mm2 cross-sect. (Ø 0.5 mm) 2 Two-wire cable 0.5 mm2 cross-sect. (Ø 0.8 mm) 2 42 5 Figure 3 Comelit cable Art. 4577 1 mm2 cross-sect. (Ø 1.2 mm) MT SB2 01 4 Figure 2 Setting Art. 1216 Braided and shielded cable 1 mm2 cross-sect. (Ø 1.2 mm) 3 Art. 3309 Table of Art. 1216 Settings according to the type of connection cable used Type of cable 2 1. Connect the terminal boards of modules Art. 3323/4 and Art. 3323/6 together and with the terminal board of the Art. 4660 or Art. 1602 group using the special cables. Insert the modules Art. 3323/4 and Art. 3323/6 on the relative terminal boards (figure 1). 2. On the terminal board of module Art. 4660 or Art. 1602 connect the power supply to ~~ , connect PR to -- and move P/O from OCC to V+ (figure 2) using the jumpers present on the terminal board itself. Connect the terminal board to module Art. 4660 or Art. 1602 assembled as shown previously. (Warning - modules Art. 3323/4 and Art. 3323/6 to be programmed must already be positioned) (figure 2). NOTE: for connection between the terminal board and module Art. 4660 or Art. 1602, it is possible to use the cable Art. 3309, available as an optional accessory (figure 3) during the programming stage. 3. Set the Dip switches located on the rear of the audio module with the same code assigned to the telephone or monitor according to the correspondence described in the programming table on page 41. 4. Press the push-button to be associated with the telephone call. A confirmation tone signals that programming has taken place. 5. On completion of programming, put the jumpers back into their initial positions, PR on PR and P/O on OCC. Setting main or secondary external unit. Modules Art. 4660 and Art. 1602 normally function as main external unit (timed engaged signal). To set them as secondary external unit (engaged signal active for the whole time the riser is in use), it is necessary to put all the Dip switches of the selector to ON. O N 1 ENGLISH Push-button programming with audio Art. 1602 and video Art.4660 group and modules Art. 3323/4 and 3323/6 MT SB2 01 • When the visitor presses the call button the bell of the internal unit is activated. • There is a reassurance tone for the call having been made at the external unit. If the call confirmation tone is not heard in systems with several entrances, it means that another conversation is taking place with another external unit installed on the same riser. In the case where Art. 3346 - system engaged signalling module is installed, wait until the module turns off before making the call again. In the case where Art. 3340 is installed, indication of the system being engaged is shown on the display. • At the internal unit, communication takes place by lifting the handset. • The button marked with the key symbol acts on the electric lock of the external unit, activating it for about 2 sec. • By pressing the call button on the external unit in video door entry systems, the infrared LEDs (not visible to the human eye) for illumination of the caller light up. The image remains on the monitor for about 90 sec. • See page 28 and 29 for microphone volume and call tone volume adjustment of the telephones. • See page 24 and 25 for call tone volume adjustment of the monitor. • See page 32 for adjustment of audio volumes on the external unit. • To enable the Self-ignition function, it is necessary to keep push-button 2 pressed for more than 2 sec. (see variant H on page 111). A confirmation tone is heard on completion of setting. • Monitor Self-ignition (if the function has been enabled) takes place by pressing push-button 2. In the case where two external units are installed, by pressing push-button 2 of monitor self-ignition in succession, there is the possibility of displaying first one image and then the other of the two external units on the monitor (alternating function between two entrances). • To vary the brightness of the monitor, use the adjustment wheel at the bottom. • To vary the call tone volume, use the special graduated deviator located on the bottom of the monitor. • It is possible to set the Privacy function with optional card Art. 4703. By pressing push-button 4 of the monitor for more than 2 sec., the LED signalling that the monitor has been set on Privacy lights up (see variant I on page 112). On privacy, the monitor does not ring, it lights up and in any case there is the possibility of going into audio with the external unit after the call. • By replacing the handset of the internal unit, you have a few seconds to replace the audio with the external unit. From the moment of hanging up, a few seconds pass before the image disappears from the monitor. • The monitor set as Main (factory setting of bracket Art. 4714W/2) lights up on a call and on self-ignition even if it is inserted as additional monitor with same user code. • The monitor set as Secondary (see variant SB2/A1-A2) does not light up on a call, but there is the possibility of self-ignite it by pressing push-button 2 (video request function). In that case, there is no possibility of self-ignite the monitor. Notice the difference between self-ignition, i.e. lighting up of the monitor with the system free with the possibility of alternating the image between two external units and the video request only active after a call. • Monitor and telephones with same user code all ring at the same time (regardless of whether they are main or secondary) on a call from the external unit and on a local floor call. 43 MT SB2 01 ENGLISH OPERATING NOTES MT SB2 01 Système Simplebus2 • GENERALITES page 46 • REGLES D’INSTALLATION page 59 • AVERTISSEMENTS page 46 • CONFIGURATION DES DISPOSITIFS page 62 • POSTES INTERIEURS VIDEO page 46 • NOTES DE FONCTIONNEMENT page 65 • POSTES INTERIEURS AUDIO page 50 • SCHEMAS DE CONNEXION page 88 • PLAQUES DE RUE page 51 • ALIMENTATIONS ET ACCESSOIRES page 56 • VARIANTES AUX SCHEMAS DE CONNEXION DE BASE page 98 45 MT SB2 01 FRANÇAIS SOMMAIRE FRANÇAIS GROUP S.P.A. GENERALITES POSTES INTERIEURS VIDEO Le système “Simplebus2” se caractérise par la simplicité de son câblage qui présente seulement 2 fils non polarisés dans chaque tronçon de l’installation. De ce fait, aucune alimentation locale ou centralisée au moyen de conducteurs additionnels n’est alors plus nécessaire. La technologie entièrement à 2 fils offre donc l’avantage de ne plus devoir se préoccuper du nombre de conducteurs à dériver du montant principal, ni du type de plaque de rue à installer. Le remplacement d’un poste intérieur parlophonique par un poste intérieur visiophonique est immédiat. Associé à la plaque de rue “Powercom” - caractérisée par sa grande facilité d’installation grâce à sa modularité - le système “Simplebus2” est extrêmement simple à câbler en éliminant toute possibilité d’erreur, tout en réduisant drastiquement les temps d’installation. En outre, une vaste gamme d’accessoires permet de résoudre facilement n’importe quelle exigence d’installation. Ce système est en mesure de gérer jusqu’à 240 usagers en connectant au maximum 3 dérivés avec le même code usager. De série, il monte les fonctions d’ouvre-porte, d’appel au HP-micro auxiliaire et de Autoallumage. De plus, des cartes en option sont disponibles pour toute exigence particulière (par ex. leds et boutons additionnels). Pour la description complète des articles concernant l’installation Simplebus2, voir le catalogue 66. Instructions pour la sécurité Pour limiter le risque de pannes et de décharges électriques: • ne pas retirer le couvercle ni effectuer personnellement les réparations. Si besoin est, demander l’intervention de techniciens spécialisés. • Ne jamais introduire des objets ni verser des liquides à l’intérieur du dispositif. • Ne jamais entraver la circulation de l’air en bouchant les fentes prévues à cet effet. Art. 4700W 4 5 6 4 1 3 9 8 7 2 1 1 AVERTISSEMENTS Suivre scrupuleusement les instructions fournies par le constructeur. Tous les appareils qui composent l’installation doivent impérativement être destinés à l’usage pour lequel ils ont été conçus. La société COMELIT GROUP S.p.A. décline toute responsabilité quant à tout préjudice matériel ou corporel qui se vérifierait à la suite d’une utilisation impropre des appareils, de modifications effectuées par d’autres à quelque titre et pour quelque objectif que ce soit et de l’emploi d’accessoires et de matériaux non d’origine. Effectuer les installations conformément aux normes en vigueur. Tous les produits sont conformes aux prescriptions contenues dans les directives CEE 73/23-89/336 et cela est attesté par la présence du marquage CE. Eviter de placer les fils du montant à proximité de câbles d’alimentation (220/380V). Avertissement pour l’usager En cas de panne ou de dysfonctionnement d’une partie quelconque de l’installation, veuillez vous adresser exclusivement à l’installateur ou à des techniciens spécialisés. 3 2 Moniteur semi-encastrable série Videocom (tube court) Caractéristiques techniques: Moniteur de la série Videocom, dimensions: 193x223x65 mm, semi-encastrable (49 mm de profondeur murale), couleur blanc RAL9010, avec écran en N/B de 4,5”, vision directe. Il peut s’installer sur le boîtier Art. 4514, mais aussi sur des boîtiers à encastrer pour séries civiles de 3 modules DIN (Art. 4517), voir page 49. A compléter avec la bride Art. 4714W/2. Le moniteur est muni de: 1. Crochets de fixation à la bride. 2. Réglage de la luminosité (tourner pour varier l’intensité). 3. Réglage du volume d’appel (déplacer vers la gauche pour augmenter le volume). 4. Bouton ouvre-porte ( ). 5. Bouton d’appel au standard / libre (1). 6. Bouton de Autoallumage / demande vidéo (2). 7. Bouton d’actionnement * (3). 8. Bouton Privacy * (4). 9. LED * (0). * disponibles seulement avec la carte en option Art. 4703W. MT SB2 01 46 MT SB2 01 Art. 4700W/I 4 1 3 9 8 7 2 4 5 6 4 1 3 2 1 1 9 8 7 1 1 3 2 FRANÇAIS 4 5 6 Art. 4701W/A 3 2 Moniteur semi-encastrable série Videocom (tube long) Moniteur mural série Videocom Caractéristiques techniques: Moniteur de la série Videocom, dimensions: 193x223x65 mm, à encastrer (68 mm de profondeur murale), couleur blanc RAL9010, avec écran en N/B de 4,5”, vision directe. A installer uniquement sur le boîtier à encastrer Art. 4514, voir page 49. A compléter avec la bride Art. 4714W/2. Le moniteur est muni de: 1. Crochets de fixation à la bride. 2. Réglage de la luminosité (tourner pour varier l’intensité). 3. Réglage du volume d’appel (déplacer vers la gauche pour augmenter le volume). 4. Bouton ouvre-porte ( ). 5. Bouton d’appel au standard / libre (1). 6. Bouton Autoallumage / demande vidéo (2). 7. Bouton d’actionnement * (3). 8. Bouton Privacy * (4). 9. LED * (0). Caractéristiques techniques: Moniteur de la série Videocom, dimensions: 193x223x65 mm, mural, couleur blanc RAL9010, avec écran en N/B de 4,5”, vision directe. A compléter avec la bride Art. 4714W/2. Le moniteur est muni de: 1. Crochets de fixation à la bride. 2. Réglage de la luminosité (tourner pour varier l’intensité). 3. Réglage du volume d’appel (déplacer vers la gauche pour augmenter le volume). 4. Bouton ouvre-porte ( ). 5. Bouton d’appel au standard / libre (1). 6. Bouton de Autoallumage / demande vidéo (2). 7. Bouton actionneur * (3). 8. Bouton Privacy * (4). 9. LED * (0). * disponibles seulement avec la carte en option Art. 4703W. Art. 4514W et Art. 4517 Art. 4514 boîtier à encastrer moniteur Art. 4700W et Art. 4700W/I. Art. 4517 boîtier série civile 3 modules DIN utilisable pour encastrer le moniteur Art. 4700W. * disponibles seulement avec la carte en option Art. 4703W. L’utilisation du moniteur Videocom, ancienne série 4701W risque de provoquer des problèmes de fonctionnement. Art. 4703 Cartes boutons additionnels et LED Carte en option avec 2 boutons additionnels et LED de signalisation. A introduire dans tous les moniteurs de la série Videocom. 47 MT SB2 01 GROUP S.P.A. Installation moniteur mural Art. 4701W/A Art. 4714W/2 2 7 FRANÇAIS 147 cm 3 5 4 6 1 10 8 9 8 Bride Simplebus2 Bride de fixation du moniteur consentant l’installation murale du moniteur ou au moyen de la base de table Art. 4712W (voir page 49) et permettant la connexion des câbles de l’installation. Munie de bornes pour la connexion de l’appel du palier (voir variante G, page 111) pour la connexion d’un dispositif de répétition de l’appel (voir SB2/D page 105) et pour l’utilisation du bouton 1 du moniteur pour usages différents (voir variante E page 110). Possibilité d’insérer jusqu’à 3 brides ayant le même code usager dans la même installation (voir page 98). Compatible avec les installations Simplebus1. 3 1 4 Caractéristiques techniques 2 Dimensions: 158x121x24. 1. connecteur bride moniteur. 2. bornes de connexion de l’installation: 0 +20V bornes de connexion Art 1212/B. L L connexion ligne bus. CFP CFP entrée appel du palier. P1 C1 bouton pour usages divers. Pour avoir un contact libre NO, couper les cavaliers CV3 et CV4. S+ Sbornes pour le dispositif de répétition de l’appel. 3. CV5 Cavalier de débranchement vidéo. 4. JP1 jumper de validation de la demande vidéo (voir variante F, page 110). 5. CN2 connecteur pour la programmation. 6. Dip switches pour la programmation du code usager. 7. CV1, CV2, CV7 cavaliers d’alimentation du moniteur additionnel au moyen de l’Art. 1212/B (voir variante SB2/A3 page 101). 8. CV3, CV4 cavalier pour dégager le bouton 1. 9. CV6 cavalier de sélection du type de fonctionnement (Simplebus2 ou Simplebus1). 10. JP2 jumper de sélection du type de fonctionnement (Simplebus2 ou Simplebus1). MT SB2 01 48 1 3 1 4 2 2 MT SB2 01 Installation base de table Art. 4712W pour moniteur Art. 4701W/A et Art. 4700W FRANÇAIS 145 cm Installation moniteur mural Art. 4700W et Art. 4700W/I Pour Per monitor Art. moniteurs 4700W Art. 4700W 4700W/I 4700W/I Art. 4514 seulement pour solo per monitor moniteurs Art. 4700W Art. 4700W Art. 4517 1 4 3 1 2 2 4 1 3 2 49 MT SB2 01 GROUP S.P.A. Installation moniteur semi-encastrable Art. 4700W avec adaptateur mural Art. 4704 147 cm 4 1 3 2 FRANÇAIS Art. 4704 Art. 4700W Comment déposer le moniteur POSTES INTERIEURS AUDIO Art. 2408W/A + C MI 5 6 3 4 + 1 2 MT SB2 01 50 Combiné parlophonique Combiné parlophonique de la série Okay, dimensions 85x223x65 mm. Muni d’un bouton ouvre-porte et d’un bouton d’appel du standard, utilisable comme bouton pour usages différents dans les installations non équipées d’un HP-micro (voir variante A page 108). Equipé d’une série de fonctions d’appel du palier (voir variante B page 108). Possibilité de monter jusqu’à 3 combinés parlophoniques ayant le même code usager dans la même installation. Pour programmer le code usager voir : “Programmation des combiné parlophonique Art. 2408W/A, 2428W et bride Art. 4714W/2” à la page 62. A utiliser uniquement pour des installations audio. Caractéristiques techniques: 1. Bouton ouvre-porte. 2. Bouton d’appel du standard / bouton pour usages divers présent dans la boîte à bornes (AB). 3. Bornes de connexion à l’installation: L L connexion à la ligne bus. CFP CFP entrée appel du palier. AB bouton normalement destiné à des services divers. Pour avoir un contact libre NO couper les cavaliers CV1 et CV2. 4. Dip switches de programmation du code usager (voir page 63). 5. Trimmer de réglage du volume du micro. 6. Trimmer de réglage du volume de la sonnerie. MT SB2 01 PLAQUES DE RUE Art. 2410W Les installations Simplebus2 peuvent monter des plaques de rue Série Powercom, Vandalcom et Logicom. Pour les séries Vandalcom et Logicom, se référer à la fiche technique FT/SB/01 et au Catalogue 50. HP-micro Série Powercom Combiné parlophonique Combiné parlophonique comme l’Art. 2408W/A avec adjonction d’un interrupteur et d’une led additionnelle pour le service Privacy ou Docteur (ouverture automatique de la gâche électrique à la suite d’un appel). Pour la connexion à l’installation, voir la fiche technique dans l’emballage de l’article. + C MI 5 6 4 + 3 1 2 Combiné parlophonique Combiné parlophonique de la série Okay, dimensions 85x223x65 mm. Muni d’un bouton ouvre-porte et d’un bouton d’appel du standard, utilisable pour des usages différents dans les installations non équipées d’un standard (voir variante C page 109). Equipé d’une série de fonctions d’appel du palier (voir variante D page 109) et de répétition de l’appel (voir SB2/D page 105). Combiné parlophonique à monter dans les installations mixtes audio-vidéo en amont de l’Art. 4896 ou dans des installations audio en cas de nécessité d’une fonction de répétition de l’appel. Possibilité de monter jusqu’à 3 combinés parlophoniques ayant le même code usager dans la même installation. Pour la modalité d’insertion de combinés parlophoniques additionnels ayant le même code usager, voir les variantes SB2/A4 et SB2/A5 page 102. Pour la programmation du code usager, voir "Programmation des combiné parlophonique Art. 2408W/A, 2428W et la bride Art. 4714W/2" page 62. Caractéristiques techniques: 1. Bouton ouvre-porte. 2. Bouton d’appel du standard / bouton pour usages divers présent dans la boîte à bornes (P1 C1). 3. Bornes de connexion à l’installation: L L connexion à la ligne bus. CFP CFP entrée appel du palier. P1 C1 bouton normalement destiné à des services divers. Pour avoir un contact libre NO couper les cavaliers CV2 et CV3. S+ S- bornes de connexion d’un dispositif de répétition de la sonnerie. 4. Dip switches de programmation du code usager (voir page 63). 5. Trimmer de réglage du volume du micro. 6. Trimmer de réglage du volume de la sonnerie. Composé des Art. 3320 + Art. 1602. HP-micro avec boîte à bornes et double amplificateur, haut-parleur étanche et micro à électret. Volume du micro et du haut-parleur réglable frontalement sur l’Art.1602 (voir page 54); possibilité de réglage par le dos en cas de montage sur l’Art. 3320. Le micro est amovible pour améliorer le rendement sonore (voir page 54). Bouton d’appel en alliage d’aluminium avec étiquette porte-nom enlevable frontalement. Equipé d’un microprocesseur et de dip switches à 8 positions pour la programmation des appels aux usagers. Pour la programmation des boutons voir page 64. Alimentation 12V CA (utiliser l’Art. 1195). Fonction ouvre-porte par switch électronique embarqué (3A seulement courant alternatif). Dimensions 112x89,5x40 mm. HP-micros vidéo série Powercom Se compose des Art. 3321 + Art. 4660. Caméra orientable à haute sensibilité pinhole CCD 1/4” N/B. Eclairage à l’infrarouge (6 LEDS). Equipé d’une boîte à bornes et d’un HP micro avec double amplificateur, haut-parleur étanche et micro à électret. Volume du micro et du haut-parleur réglable frontalement sur l’Art. 4660 (voir page 54); possibilité de réglage par le dos en cas de montage sur l’Art. 3321. Le micro est amovible pour améliorer le rendement sonore (voir page 54). Bouton d’appel en alliage d’aluminium avec étiquette porte-nom enlevable frontalement. Equipé d’un microprocesseur et de dip switches à 8 positions pour la programmation des appels aux usagers. Pour la programmation des boutons voir page 64. Alimentation 12V CA (utiliser l’Art. 1195). Fonction ouvre-porte par switch électronique embarqué (3A seulement courant alternatif). Dimensions 112x89,5x40 mm. 51 MT SB2 01 FRANÇAIS Art. 2428W GROUP S.P.A. Art. 3110 Art. 3340 Boîtiers à encastrer Disponibles pour 1, 2 et 3 modules. Dimensions un module 127x127x45 mm. FRANÇAIS Art. 3311 Cadres porte-modules avec encadrement Réalisés en aluminium moulé sous pression et revêtus de peintures particulières résistant à l’environnement extérieur. Disponibles pour 1, 2 et 3 modules dans les couleurs Gris, Blanc, Bleu et Orange. Dimensions un module 125x125x15,5 mm. Module d’appel numérique avec répertoire électronique Avec afficheur LCD graphique 128x64 dots, plaque de rue à 16 boutons rétroéclairés avec led bleue. Il fait aussi fonction de digicode avec la possibilité d’entrer jusqu’à 250 mots de passe. Il est équipé d’un module répertoire porte-noms électronique mémorisant 400 noms d’usagers. Le défilement des noms s’effectue en appuyant sur deux boutons de recherche ou en numérisant directement l’initiale du nom ou le code usager. A l’affichage du nom de l’usager désiré, il suffit d’appuyer sur le bouton d’appel. L’entrée des noms des usagers s’effectue d’une manière simple au moyen du programmateur art. 1230 ou du logiciel pour micro-ordinateur PC art. 1249 ou du clavier codé. Dimensions 112x180x40 mm. Art. 3342 Art. 3316 Boîtiers saillie Boîtier en acier inox. Disponible pour 1, 2, 3, 4, 6 et 9 modules. Mural également pour environnement extérieur. Utile en cas d’impossibilité d’encaisser le boîtier. Dimensions un module 123x123x32,5 mm. Module répertoire électronique Module répertoire porte-noms électronique, avec afficheur graphique 128x64 dots. Mémorise 400 noms d’usagers. Le défilement des noms s’effectue en appuyant sur deux boutons de recherche. Après affichage du nom de l’usager désiré il suffira d’appuyer sur le bouton d’appel. La programmation des noms des usagers s’effectue aisément au moyen du programmateur art. 1230 ou du logiciel pour micro-ordinateur P.C. Art. 1249. Dimensions: 112x89,5x40 mm. Art. 3323 Art. 3346 Modules boutons d’appel Module avec boutons d’appel dotés de micro-switches et réalisés en alliage d’aluminium moulé sous pression et chromé. La led bleue d’éclairage des étiquettes porte-noms est enlevable frontalement. Disponibles à 4 et 6 boutons. Dimensions 112x89,5x40 mm. Pour la programmation des boutons voir page 64. MT SB2 01 52 Module de signalisation de ligne occupée Avec led bleue clignotante pour l’indication visuelle de l’état d’occupé. L’étiquette transparente en carton est fournie neutre pour pouvoir y écrire dans toutes les langues. Dimensions: 112x89,5x38 mm. MT SB2 01 Instructions pour l’installation de la plaque de rue audio et vidéo Comment associer plusieurs boîtiers FRANÇAIS 160 - 165 cm Hauteur boîtier à encastrer Fixation du petit câble sur le boîtier à encastrer Fixation du cadre sur le boîtier mural Connexion cadre à 4 pôles Câblage boîte à bornes insérée ou retirée 53 MT SB2 01 GROUP S.P.A. Introduction modules Montage connexions et réglages groupe audio-vidéo + C MI FRANÇAIS + Position alternative du micro Pose/dépose éléments frontaux 3 4 2 5 1 Fixation cadre Pose/dépose étiquettes 1 360˚ open 2 3 MT SB2 01 close 54 rla Ca ssi Ro MT SB2 01 Instructions pour le montage des modules d’information Art. 3326, Art. 3344 et Art. 3346 Connexion câble à 4 pôles Introduction module Retrait porte-étiquette FRANÇAIS 10 Introduction/retrait étiquette 10 15 1 2 55 MT SB2 01 GROUP S.P.A. ALIMENTATIONS ET ACCESSOIRES Art. 1122/A FRANÇAIS Art. 1246 Transformateur pour mélangeur-alimentation Transformateur 65VA. (T 1’on / 5’off). Primaire 230VCA Secondaire: OUT1: 36VAC 1,5A OUT2: 14VAC 1A Relais Relais 12-24V CC-CA 5A pour usages généraux. Peut être commandé directement par la sortie de répartition de l’appel de la bride Art. 4714W/2 ou par les combinés parlophoniques Art. 2428W. Dimensions: 66x85x35 mm (4 modules DIN). Bornes connexion installation: + alimentation relais. C-NO-NC contacts relais. Le transformateur est équipé d’un PTC intérieur de protection. Dimensions: 107x90x60 (8 modules DIN). Art. 1212/B Art. 1224 Commutateur Alimentation 12 VCA – 20 VCC. Dimensions: 66x85x35 mm (4 modules DIN). Bornes de connexion à l’installation: ~~* alimentation 12VCA-20VCC. LS LS entrée ligne bus plaque de rue secondaire. LP LP entrée ligne bus plaque de rue principale. LM LM sortie ligne bus du montant. Pour la programmation du commutateur voir page 62. Alimentation pour moniteur additionnel Alimentation 15VA (interm.). Entrée: 230VCA Sortie: 0- 20VDC 700mA Le transformateur est équipé d’un PTC intérieur de protection. Dimensions: 87x105x65 (5 modules DIN). Art. 1214/2 et Art. 1216 Art. 1214/2 Art. 1216 Borne de dérivation et borne de terminaison de ligne Voir page 64 pour la configuration de l’Art. 1216 selon le câble utilisé. Bornes de connexion à l’installation: Lin Lin: entrée ligne montant. Lout Lout: sortie ligne montant. LM LM: ligne montant dérivée vers le moniteur/combiné parlophonique. + +: bornes connexion alimentation pour compatibilité avec les installations Simplebus1. MT SB2 01 56 MT SB2 01 Art. 1195 JP1 Transformateur Transformateur 60VA (interm). Primaire 230VAC Secondaire: OUT1: 0-12V 1,5A OUT2: 0-12V 1,5A Le transformateur est équipé d’un fusible intérieur de protection. Dimensions: 87x105x65 (5 modules DIN). L’Art. 4896 doit être alimenté par le transformateur Art.1246. Exécuter les opérations de câblage et de connexion de l’installation en débranchant l’alimentation de réseau. Cet article est équipé d’un PTC de protection après un court-circuit, pour le réactiver couper l’alimentation pendant environ une minute. Brancher la ligne en entrée de la plaque de rue et alimenter ensuite également le module mélangeur Art. 4896. Le dispositif consent d’alimenter au maximum un moniteur et de gérer au maximum MAX 100 usagers. Art. 4896 Bornes de connexion de l’installation: 1. Lin Lin connexion à la ligne venant de la plaque de rue. Mélangeur-alimentation Le mélangeur-alimentation Art. 4896 est contenu dans un boîtier à 12 modules DIN. Dimensions: 208x140x65 mm. Pour pouvoir accéder aux bornes de connexion, retirer les couvercles latéraux conformément aux indications illustrées dans la figure. 2. 0V 36V connexion aux bornes OUT1 du transformateur Art. 1246. 0V 14V connexion aux bornes OUT2 du transformateur Art. 1246. 3. L1 L1 L2 L2 L3 L3 L4 L4 sortie dérivation 1 du montant. sortie dérivation 2 du montant. sortie dérivation 3 du montant. sortie dérivation 4 du montant. 4. Jumpers à programmer selon le nombre total d’usagers connectés au mélangeur –alimentation Art.4896. JP1 et JP2 sur la position 3 pour les installations ayant de 0 à 15 usagers JP1 et JP2 sur la position 2 pour les installations ayant de 16 à 35 usagers JP1 et JP2 sur la position 1 pour les installations ayant de 36 à 100 usagers. JP1 - JP2 1 2 4 1 3 2 3 4 57 MT SB2 01 FRANÇAIS JP2 GROUP S.P.A. Art. 4833/A Câble Comelit Simplebus2 Câble spécial pour les installations Simplebus2: il se compose de deux conducteurs ayant une section de 1mm2 tressés de couleur rouge et noire. Disponibles en bobines de 100 et de 500 m. Amplificateur de ligne Amplificateur pour installations vidéo Simplebus1. Il régénère le signal du montant relativement au composant vidéo. Alimentation: 12V CA ou 20V CC. A monter exclusivement sur le tronçon en entrée aux mélangeurs-alimentations Art. 4896. Dimensions: 66x85x35 mm (4 modules DIN). FRANÇAIS Art. 4577 Bornes connexion installation: Lin Lin: entrée ligne montant. Lout Lout: sortie ligne montant. ~+ ~-: alimentation module. Art. 1254 Art. 4834/2 Relais pour services divers Alimentation 12VCA, 20VCC. Portée relais: 10A. Cet accessoire permet: • service répétition sonnerie. • service commande relais du poste intérieur dans des installations sans standard. • service éclairage escalier. • service ouvre-porte secondaire. Pour le câblage et l’explication des services voir la documentation de l’Art. 1254. Concentrateur de ligne Concentrateur de ligne pour installation Simplebus vidéo. Il permet de distribuer le signal sur 4 montants. A monter exclusivement sur le tronçon d’installation en entrée dans les mélangeurs art. 4896. Dimensions: 66x85x35 mm (4 modules DIN). MT SB2 01 58 Bornes connexion installation: Lin Lin: entrée ligne montant. L1 L1: sortie dérivation 1 du montant. L2 L2: sortie dérivation 2 du montant. L3 L3: sortie dérivation 3 du montant (couper la résistance avant d’introduire les câbles). L4 L4: sortie dérivation 4 du montant (couper la résistance avant d’introduire les câbles). MT SB2 01 Règles d’installation pour installations visiophoniques Eviter de placer les fils du montant à proximité de câbles d’alimentation (220/380V). Dans les dérivations vers chaque usager, introduire sur le montant la borne Art. 1214/2 fournie avec la bride Art. 4714W/2 ou en vente séparément pour les combinés parlophoniques Art. 2428W. Terminer chaque montant ou chaque dérivation par l’Art. 1216 fourni avec le mélangeur-alimentation Art. 4896 et avec le module vidéo Art. 4660. En fonction du câble utilisé pour le montant programmer la fermeture sur l’Art. 1216 comme illustré dans le tableau de la page 64. En fonction du câble utilisé pour le montant, évaluer la distance maximum pouvant être atteinte entre l’alimentation-mélangeur Art.4896 et le moniteur le plus éloigné et entre la borne de dérivation Art. 1214/2 et le moniteur le plus éloigné. En fonction du câble utilisé pour la connexion évaluer la distance maximum pouvant être atteinte entre la plaque de rue vidéo et le mélangeur-alimentation Art. 4896. Se référer aux tableaux de la page 60 pour évaluer les distances en fonction des conducteurs. Chaque Art.4896 peut gérer au MAX 4 dérivations du montant voir variante SB2/B page 103. En cas d’installations munies de portes principales et secondaires (voir schéma SB2V/EN/112 page 97) il faudra employer le concentrateur de ligne Art. 4834/2 et le commutateur Art. 1224. S'il y a une seule porte, on pourra brancher jusqu’à 4 mélangeursalimentations Art. 4896 après l’Art. 4834/2 (voir le schéma SB2V/012 page 94). Chaque Art. 4834/2 permet au MAX 4 dérivations: en cas de nécessité de plusieurs dérivations (jusqu’à 16) il faudra mettre en cascade deux Art. 4834/2. L’Art. 4834/2 additionnel doit être précédé de son amplificateur de signal vidéo correspondant Art. 4833/A (voir variante SB2/C page 104). Possibilité d’insérer jusqu’au MAX 2 Art.4834/2 en cascade. Le nombre MAX d’usagers pouvant être branché à un seul mélangeur-alimentation Art. 4896 est de 100 usagers, indépendamment qu’ils soient distribués sur un seul montant ou sur plusieurs dérivations du montant (ex 100 usagers sur un montant ou 25 usagers sur chacune des 4 dérivations du montant). Possibilité de brancher jusqu’à 25 moniteurs en cascade pour chaque dérivation du montant (voir variante SB2/G page 106); dans ce cas, pour déterminer la distance MAX entre la plaque de rue et le dernier moniteur de la cascade, se référer au tableau page 60 colonne A. La connexion entre plusieurs moniteurs ayant le même code usager (MAX 3) peut avoir lieu en cascade ou en dérivation du montant en suivant les variantes SB2/A1-A2-A3-A4-A5 (pages 99-100-101-102). Les combinés parlophoniques Art. 2428W ayant le même code usager que le moniteur doivent être dérivés directement du montant au moyen de l’Art. 1214/2. L’Art. 4896 alimente un seul moniteur pour chaque appel, par conséquent, pour les installations avec plusieurs moniteurs ayant le même code usager, il faudra programmer les moniteurs additionnels comme secondaires ou alimenter séparément à travers l’Art.1212/B chaque moniteur additionnel (voir pages 99-100-101). Programmer les cavaliers et les jumpers sur la bride Art. 4714W/2 de la manière illustrée dans les variantes aux schémas de base SB2/A1-A2-A3, selon la configuration que l’on désire obtenir. Ne jamais orienter les caméras des plaques de rue vers des sources de lumière directe (ex. lampes, lumière solaire, surfaces réfléchissantes, etc….). 59 MT SB2 01 FRANÇAIS REGLES D’INSTALLATION GROUP S.P.A. Distances maximums caractéristiques des conducteurs La connexion des appareils est de type non polarisé. L’emploi de conducteurs ayant des caractéristiques différentes de celles prescrites ne garantit pas l’obtention de distances d’intervention déterminées, ni la bonne qualité du signal vidéo. Veuillez utiliser exclusivement les câbles décrits dans les tableaux suivants. Distance MAX entre le mélangeur Art. 4896 et le poste intérieur. FRANÇAIS Type de câble Distance MAX entre la plaque de rue et le mélangeur Art. 4896. Distance MAX entre la plaque de rue et l’Art. 4833/A. Distance MAX entre l’Art. 4833/A et le mélangeur Art. 4896. Distance MAX entre la plaque de rue et le mélangeur ou l’amplificateur Art. 4833/A avec un Art. 4834/2 branché. Distance MAX entre la borne de dérivation 1 Art. 1214/2 et le poste intérieur. A B C D E H Câble Comelit Art. 4577 sect. 1 mm2 (Ø 12/10) 200 m 200 m 200 m 200 m 150 m 60 m Câble bifilaire sect. 1,5 mm2 (Ø 14/10)** 150 m 100 m 100 m 100 m 80 m 40 m 120 m 80 m 80 m 80 m 50 m 30 m Boucle téléphonique retorse (sect. 0,28 mm2 (Ø 6/10) * 100 m 150 m 150 m 150 m 100 m 40 m Câble UTP5 cat. 5 AWG 24 (sect. 0,2 mm2 (Ø 5/10) * 80 m 150 m 150 m 150 m 100 m 40 m 120 m 100 m 100 m 100 m 80 m 40 m Câble tressé et blindé sect. 1 mm2 (Ø 12/10)* Câble bifilaire sect. 0,5 mm2 (Ø 8/10) ** * Dans le cas où on utilise un câble multipaires torsadées, on doit utiliser uniquement une paire torsadée disponible. Dans le cas de grande longueur afin de réduire la perte on utilise une paire comme un fil simple. ** Dans le cas d’un câble multifils, il faut utiliser seulement deux fils disponibles et ne pas mettre plusieurs fils en parallel. Distances maximums pouvant être atteintes pour les conducteurs d’alimentation du moniteur additionnel et de la plaque de rue Section du conducteur Distance MAX entre le transformateur Art. 1195 et la plaque de rue. Distance MAX entre l’alimentation Art. 1212/B et le poste intérieur. F G (Ø 6/10) 4m 10 m 0,5 mm 2 (Ø 8/10) 10 m 25 m 1 mm 2 (Ø 12/10) 20 m 50 m 1,5 mm 2 (Ø 14/10) 30 m 100 m 2 mm 2 (Ø 16/10) 40 m 150 m 0,28 mm 2 MT SB2 01 60 MT SB2 01 FRANÇAIS Figures pour les distances 61 MT SB2 01 GROUP S.P.A. CONFIGURATION DES DISPOSITIFS FRANÇAIS 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Programmation des combinés parlophoniques Art. 2408W/A, 2410W, 2428W et de la bride Art. 4714W/2 • Tous les combinés parlophoniques ou les brides du système sont identifiés par un code propre qui doit être programmé avec le dip switch présent sur la carte parlophonique ou sur la bride (voir figures). • Le code usager doit être programmé selon la correspondance décrite dans le tableau de programmation de la page 63. • Le codage peut être effectué à n’importe quel moment, même en l’absence d’alimentation. Programmation du commutateur Art. 1224 • Exemple de codage du commutateur Art. 1224 de l’escalier A nombre minimum 1, nombre maximum 10. X MA N MI O1 N 2 3 4 5 6 7 O1 8 N 2 3 4 5 6 7 8 ESCALIER A SCALA A 1÷10. N° 1÷10 4700 W 4700 W/I 4701 W/A 4700 W 4700 W/I 4701 W/A 4700 W 4700 W/I 4701 W/A 4700 W 4700 W/I 4701 W/A ESCALIER SCALA B B N° N° 11÷20. 11÷20 PORTE PRINCIPALE DU N° PORTA PRINCIPALE DAL N° 1÷20. 1÷20. • Chaque module de commutation monte deux dip switches à 8 sélecteurs (voir figure). Les deux dip switches définissent la plage minimum MIN et maximum MAX des codes pouvant être reconnus par le commutateur. • N’oubliez pas que les dip switches MIN et MAX définissent respectivement le code usager le plus bas et le code usager MT SB2 01 62 le plus haut pouvant être branchés au montant. • Pour programmer les valeurs désirées, se référer au tableau de la page 63. • Des commutations distinctes doivent gérer des intervalles de codes non superposés. MT SB2 01 Tableau de programmation des dip switches 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 1 2 1,2 3 1,3 2,3 1,2,3 4 1,4 2,4 1,2,4 3,4 1,3,4 2,3,4 1,2,3,4 5 1,5 2,5 1,2,5 3,5 1,3,5 2,3,5 1,2,3,5 4,5 1,4,5 2,4,5 1,2,4,5 3,4,5 1,3,4,5 2,3,4,5 1,2,3,4,5 6 1,6 2,6 1,2,6 3,6 1,3,6 2,3,6 1,2,3,6 4,6 1,4,6 2,4,6 1,2,4,6 3,4,6 1,3,4,6 2,3,4,6 1,2,3,4,6 5,6 1,5,6 2,5,6 1,2,5,6 3,5,6 1,3,5,6 2,3,5,6 1,2,3,5,6 4,5,6 1,4,5,6 2,4,5,6 1,2,4,5,6 3,4,5,6 Nom usager Code u. Dip switches sur ON 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 1,3,4,5,6 2,3,4,5,6 1,2,3,4,5,6 7 1,7 2,7 1,2,7 3,7 1,3,7 2,3,7 1,2,3,7 4,7 1,4,7 2,4,7 1,2,4,7 3,4,7 1,3,4,7 2,3,4,7 1,2,3,4,7 5,7 1,5,7 2,5,7 1,2,5,7 3,5,7 1,3,5,7 2,3,5,7 1,2,3,5,7 4,5,7 1,4,5,7 2,4,5,7 1,2,4,5,7 3,4,5,7 1,3,4,5,7 2,3,4,5,7 1,2,3,4,5,7 6,7 1,6,7 2,6,7 1,2,6,7 3,6,7 1,3,6,7 2,3,6,7 1,2,3,6,7 4,6,7 1,4,6,7 2,4,6,7 1,2,4,6,7 3,4,6,7 1,3,4,6,7 2,3,4,6,7 1,2,3,4,6,7 5,6,7 1,5,6,7 2,5,6,7 1,2,5,6,7 3,5,6,7 1,3,5,6,7 2,3,5,6,7 1,2,3,5,6,7 4,5,6,7 Nom usager Code u. Dip switches sur ON 121 1,4,5,6,7 122 2,4,5,6,7 123 1,2,4,5,6,7 124 3,4,5,6,7 125 1,3,4,5,6,7 126 2,3,4,5,6,7 127 1,2,3,4,5,6,7 128 8 129 1,8 130 2,8 131 1,2,8 132 3,8 133 1,3,8 134 2,3,8 135 1,2,3,8 136 4,8 137 1,4,8 138 2,4,8 139 1,2,4,8 140 3,4,8 141 1,3,4,8 142 2,3,4,8 143 1,2,3,4,8 144 5,8 145 1,5,8 146 2,5,8 147 1,2,5,8 148 3,5,8 149 1,3,5,8 150 2,3,5,8 151 1,2,3,5,8 152 4,5,8 153 1,4,5,8 154 2,4,5,8 155 1,2,4,5,8 156 3,4,5,8 157 1,3,4,5,8 158 2,3,4,5,8 159 1,2,3,4,5,8 160 6,8 161 1,6,8 162 2,6,8 163 1,2,6,8 164 3,6,8 165 1,3,6,8 166 2,3,6,8 167 1,2,3,6,8 168 4,6,8 169 1,4,6,8 170 2,4,6,8 171 1,2,4,6,8 172 3,4,6,8 173 1,3,4,6,8 174 2,3,4,6,8 175 1,2,3,4,6,8 176 5,6,8 177 1,5,6,8 178 2,5,6,8 179 1,2,5,6,8 180 3,5,6,8 Nom usager Code u. Dip switches sur ON Nom usager 181 1,3,5,6,8 182 2,3,5,6,8 183 1,2,3,5,6,8 184 4,5,6,8 185 1,4,5,6,8 186 2,4,5,6,8 187 1,2,4,5,6,8 188 3,4,5,6,8 189 1,3,4,5,6,8 190 2,3,4,5,6,8 191 1,2,3,4,5,6,8 192 7,8 193 1,7,8 194 2,7,8 195 1,2,7,8 196 3,7,8 197 1,3,7,8 198 2,3,7,8 199 1,2,3,7,8 200 4,7,8 201 1,4,7,8 202 2,4,7,8 203 1,2,4,7,8 204 3,4,7,8 205 1,3,4,7,8 206 2,3,4,7,8 207 1,2,3,4,7,8 208 5,7,8 209 1,5,7,8 210 2,5,7,8 211 1,2,5,7,8 212 3,5,7,8 213 1,3,5,7,8 214 2,3,5,7,8 215 1,2,3,5,7,8 216 4,5,7,8 217 1,4,5,7,8 218 2,4,5,7,8 219 1,2,4,5,7,8 220 3,4,5,7,8 221 1,3,4,5,7,8 222 2,3,4,5,7,8 223 1,2,3,4,5,7,8 224 6,7,8 225 1,6,7,8 226 2,6,7,8 227 1,2,6,7,8 228 3,6,7,8 229 1,3,6,7,8 230 2,3,6,7,8 231 1,2,3,6,7,8 232 4,6,7,8 233 1,4,6,7,8 234 2,4,6,7,8 235 1,2,4,6,7,8 236 3,4,6,7,8 237 1,3,4,6,7,8 238 2,3,4,6,7,8 239 1,2,3,4,6,7,8 *240 5,6,7,8 FRANÇAIS Code u. Dip switches sur ON *NOTE: le code 240 est réservé pour le standard. EXEMPLE programmation code 200. 63 MT SB2 01 GROUP S.P.A. Figure 1 5 6 7 8 Figure 3 Programmation Art. 1216 2 Câble bifilaire sect. 1,5 mm2 (Ø 14/10) 1 Câble tressé et blindé sect. 1 mm2 (Ø 12/10) 1 Boucle téléphonique retorse sect. 0,28 mm2 (Ø 6/10) Câble UTP5 cat. 5 AWG 24 sect. 0,2 mm2 (Ø 5/10) 2 Câble bifilaire sect. 0,5 mm2 (Ø 8/10) 2 64 4 Figure 2 Câble Comelit Art. 4577 sect. 1 mm2 (Ø 12/10) MT SB2 01 3 Art. 3309 Tableau des programmations de l’Art. 1216 en fonction du type de câble de connexion utilisé Type de câble 2 1. Brancher les boîtes à bornes des modules Art. 3323/4 et Art. 3323/6 entre elles et à la boîte à bornes du groupe Art. 4660 ou Art. 1602 en utilisant les petits câbles spéciaux. Introduire les modules Art. 3323/4 et Art. 3323/6 dans les boîtes à bornes correspondantes (figure 1). 2. Sur la boîte à bornes du module Art. 4660 ou Art. 1602 brancher l’alimentation à ~~ , brancher PR à – et déplacer P/O de OCC à V+ (figure 2) en utilisant les jumpers présents sur cette même boîte à bornes. Brancher la boîte à bornes au module Art. 4660 ou Art. 1602 assemblé de la manière précédemment indiquée. (Attention, les modules Art. 3323/4 et Art. 3323/6 à programmer doivent être déjà positionnés) (figure 2). NOTE: Pour connecter la boîte à bornes au module Art. 4660 ou Art. 1602, lors de la programmation on pourra utiliser le petit câble Art. 3309 disponible comme accessoire en option (figure 3). 3. Programmer le dip switch placé sur le dos du module audio avec le même code attribué au combiné parlophonique ou au moniteur selon la correspondance décrite dans le tableau de programmation à la page 63. 4. Appuyer sur le bouton que l’on désire associer à l’appel du combiné parlophonique. La réalisation de la programmation est signalée par un bip de confirmation. 5. A la fin de la programmation, replacer les jumpers dans leurs positions initiales, PR sur PR et P/O sur OCC. Programmation de la plaque de rue principale ou secondaire. Les modules Art. 4660 et Art. 1602 fonctionnent normalement comme plaque de rue principale (signal d’occupé temporisé). Pour les programmer comme plaque de rue secondaire (signal d’occupé actif pendant toute la durée où le montant est occupé) tous les dip switches du sélecteur doivent être placés sur ON. O N 1 FRANÇAIS Programmation des boutons avec groupe audio Art. 1602 et vidéo Art. 4660 et modules Art. 3323/4 et 3323/6 MT SB2 01 • A l’appui sur la touche d’appel, le visiteur actionne la sonnerie du poste intérieur. • La plaque de rue émet un bip indiquant que l’appel a eu lieu. Lorsque, dans les installations à plusieurs entrées, le bip de confirmation de l’appel n’est pas audible, c’est l’indice qu’une autre conversation est en cours vers une autre plaque de rue installée sur le même montant. En cas d’installation de l’Art. 3346, module de signalisation d’installation occupée, attendre jusqu’au débranchement du module avant de rappeler. En cas d’installation de l’Art. 3340, l’indication d’occupé s’inscrit à l’afficheur. • Pour entrer en communication à partir du poste intérieur, décrocher le bras du combiné téléphonique. • La touche, marquée du symbole de la clé, agit sur la gâche électrique de la plaque de rue en l’activant pendant environ 2 sec. • Dans des installations visiophoniques, l’appui sur la touche d’appel de la plaque de rue branche les leds à l’infrarouge (non visibles à l’œil humain) pour éclairer la personne; l’image demeure affichée à l’écran pendant environ 90 sec. • Pour régler le volume du micro et celui de la sonnerie des combinés parlophoniques, voir les pages 50 et 51. • Pour régler le volume de la sonnerie des moniteurs, voir les pages 46 et 47. • Pour régler les volumes audio sur la plaque de rue voir la page 54. • Pour valider la fonction de Autoallumage, continuer à appuyer sur le bouton 2 pendant plus de 2 sec. (voir variante H page 111). A la fin de la programmation un bip de confirmation est émis. • Le Autoallumage du moniteur (si la fonction a été validée), a lieu en appuyant sur le bouton 2. En cas d’installation de deux plaques de rue, l’appui à plusieurs reprises sur le bouton 2 de Autoallumage du moniteur permet d’afficher l’image d’abord de l’un, ensuite de l’autre, des deux plaques de rue (fonction de bascule entre deux entrées). • Pour varier la luminosité du moniteur, intervenir sur la molette de réglage placée sur la partie inférieure. • Pour varier le volume de la sonnerie d’appel intervenir sur le déviateur gradué spécial placé sur la partie inférieure du moniteur. • La carte en option Art. 4703 permet de programmer la fonction Privacy. L’appui pendant plus de 2 sec. sur le bouton 4 du moniteur branche la led signalant que la programmation du moniteur en Privacy a eu lieu (voir variante I page 112). En Privacy le moniteur ne sonne pas, il se branche et l’on a de toute façon la possibilité de communiquer oralement avec la plaque de rue après l’appel. • Lorsqu’on raccroche le bras du combiné intérieur on dispose de quelques secondes pour reprendre la conversation phonique avec la plaque de rue. Après avoir raccroché le bras, quelques secondes sont nécessaires pour que l’image s’efface du moniteur. • Le moniteur programmé comme Principal (programmation d’origine de la bride Art. 4714W/2) se branche à l’appel et au Autoallumage, même s’il est branché comme moniteur additionnel avec le même code usager. • Le moniteur programmé comme Secondaire (voir variante SB2/A1-A2) ne se branche pas à l’appel mais il peut être branché en appuyant sur le bouton 2 (fonction demande vidéo). Dans ce cas, le Autoallumage du moniteur ne peut pas être effectué. A remarquer la différence entre le Autoallumage, c’est-à-dire le branchement du moniteur lorsque l’installation est libre, avec la possibilité de faire basculer l’image entre deux plaques de rue et la demande vidéo active seulement après l’appel. • Les moniteurs et les combinés parlophoniques ayant le même code utilisateur retentissent tous en même temps (indépendamment qu’ils soient principaux ou secondaires) à l’appel de la plaque de rue et à celui du palier. 65 MT SB2 01 FRANÇAIS NOTES DE FONCTIONNEMENT MT SB2 01 Simplebus2 Systeem INHOUD pag. 68 • INSTALLATIEVOORSCHRIFTEN pag. 81 • WAARSCHUWINGEN pag. 68 • CONFIGURATIE VAN DE APPARATUUR pag. 84 • MONITOREN pag. 68 • WERKING pag. 87 • DEURTELEFOONS pag. 72 • AANSLUITSCHEMA’S pag. 88 • ENTREEPANELEN pag. 73 • VARIANTEN VAN DE STANDAARD AANSLUITSCHEMA’S pag. 98 • VOEDINGEN EN ACCESSOIRES pag. 78 NEDERLANDS • ALGEMENE INFORMATIE 67 MT SB2 01 NEDERLANDS GROUP S.P.A. ALGEMENE INFORMATIE MONITOREN Het kenmerk van het “Simplebus2” systeem is de eenvoudige installatie met slechts 2 omkeerbare aders voor de hele installatie. Hierdoor zijn geen plaatselijke voedingen meer nodig, of een centrale voeding met extra aders in de installatie. Deze 2-draads technologie biedt het voordeel dat het aantal draden altijd voldoende is voor het aansluiten van het maximum aan binnentoestellen, of dit nu een audio systeem is of een audio/video systeem. Een gewoon deurtelefoontoestel kan direct vervangen worden door een videofoon toestel. Wanneer dit systeem gecombineerd wordt met de “Powercom” entreepanelen, welke zeer eenvoudig te monteren zijn door de modulaire opbouw, worden mogelijke installatiefouten tot een minimum beperkt en zal een drastische tijdbesparing het gevolg zijn. Bovendien is er een breed assortiment accessoires beschikbaar om aan alle eisen te kunnen voldoen. Het systeem is uit te breiden tot maximaal 240 gebruikers, waarbij er maximaal 3 toestellen bij één gebruiker geïnstalleerd kunnen worden. Het systeem wordt standaard met deuropeningfunctie, portiersoproep / vrije drukknop en beeldoproep geleverd. Eveneens is het mogelijk optionele kaarten te installeren voor bijzondere toepassingen (bijv. LED, extra knoppen). Voor de complete omschrijving van de artikelen met betrekking tot de Simplebus2 installatie wordt verwezen naar de Catalogus 66. Veiligheidsvoorschriften Ter voorkoming of afname van het risico voor storingen en elektrische schokken: • het deksel niet verwijderen en niets eigenhandig repareren. Als het nodig mocht zijn, de hulp inroepen van vakbekwaam personeel. • Geen voorwerpen in het apparaat steken en geen vloeistof in gieten. • Sluit de luchtcirculatie niet af door de speciale sleuven te bedekken. art. 4700W 4 5 6 4 1 3 9 8 7 2 1 1 WAARSCHUWINGEN Volg nauwkeurig de door de fabrikant geleverde aanwijzingen. Alle apparaten van de installatie mogen uitsluitend gebruikt worden voor het doeleinde waarvoor ze ontworpen zijn. COMELIT GROUP S.p.A. acht zich niet aansprakelijk voor een onjuist gebruik van de apparaten, door anderen aangebrachte wijzigingen voor wat voor doeleinde dan ook en het gebruik van niet originele accessoires en materiaal. Installeer het systeem in overeenstemming met de geldende normen. Alle producten zijn in overeenstemming met de voorschriften van de richtlijnen CEE 73/23-89/336 en dit wordt aangetoond door het CE keurmerk op de apparaten. Plaats de bedrading van de stamleiding niet in de buurt van voedingskabels (220/380V). Waarschuwingen voor de gebruiker Als er iets aan de installatie defect mocht gaan of niet goed mocht werken, wend u dan uitsluitend tot de installateur of tot vakbekwaam personeel. 3 2 Halfinbouwmonitor serie Videocom (korte buis) Technische gegevens: Monitor van de serie Videocom met afmetingen 193x223x65 mm, gedeeltelijk ingebouwd (49mm diep in de muur), wit (RAL9010) met Z/W 4.5” scherm. Kan geïnstalleerd worden op de inbouwdoos art. 4514 maar ook op de inbouwdozen geschikt voor 3 DIN modulen art. 4517, zie pag. 71. Te completeren met aansluitgrondplaat art. 4714W/2. De monitor is compleet met: 1. Bevestigingshaken op de grondplaat. 2. Afstelling van de helderheid (draaien om de lichtsterkte te veranderen). 3. Afstelling van het belvolume (naar links schuiven om het volume te verhogen). 4. Deuropeningsknop ( ). 5. Knop om de centrale te bellen / vrij (1). 6. Knop voor beeldoproep / passieve beeldoproep (2). 7. Knop voor digitale functies* (3). 8. Privacy knop* (4). 9. LED* (0). * alleen beschikbaar met optionele kaart art. 4703W. MT SB2 01 68 MT SB2 01 art. 4700W/I 4 1 3 9 8 7 2 4 5 6 4 1 3 2 1 1 9 8 7 1 1 3 2 3 2 Halfinbouwmonitor serie Videocom (lange buis) Wandmonitor serie Videocom Technische gegevens: Monitor van de serie Videocom met afmetingen 193x223x65 mm, ingebouwd (68 mm diep in de muur), wit (RAL9010) met Z/W 4.5” direct-vision. Kan alleen geïnstalleerd worden op de inbouwdoos art. 4514, zie pag. 71. Te completeren met grondplaat art. 4714W/2. De monitor is compleet met: 1. Bevestigingshaken op de grondplaat. 2. Afstelling van de helderheid (draaien om de lichtsterkte te veranderen). 3. Afstelling van het belvolume (naar links schuiven om het volume te verhogen). 4. Deuropeningsknop ( ). 5. Knop om de centrale te bellen / vrij (1). 6. Knop voor beeldoproep / verzoek om video (2). 7. Knop voor actuator * (3). 8. Privacy knop * (4). 9. LED * (0). * alleen beschikbaar met optionele kaart art. 4703W. Technische gegevens: Monitor van de serie Videocom met afmetingen 193x223x65, voor aan de wand, wit RAL9010 met B/W 4.5” direct-zicht-scherm. Te completeren met aansluitgrondplaat art. 4714W/2. De monitor is compleet met: 1. Bevestigingshaken aan de aansluitgrondplaat. 2. Afstelling van de helderheid (draaien om de lichtsterkte te veranderen). 3. Afstelling van het belvolume (naar links verplaatsen om het volume te verhogen). 4. Deuropeningsknop ( ). 5. Knop om de centrale te bellen / vrij (1). 6. Knop voor beeldoproep / verzoek om video (2). 7. Knop voor actuator * (3). 8. Privacy knop * (4). 9. LED * (0). * alleen beschikbaar met optionele kaart art. 4703W. Het gebruik van de monitor Videocom oude serie 4701W kan problemen in de werking geven. art. 4514W en art. 4517 art. 4703 art. 4514 inbouwdoos monitor art. 4700W en art. 4700W/I. art. 4517 doos burgerlijke serie 3 DIN modulen bruikbaar voor inbouw monitor art. 4700W. Kaart extra knoppen en LED Optionele kaart met twee extra knoppen en signalerings LED. Kunnen in alle monitors van de serie Videocom aangebracht worden. 69 MT SB2 01 NEDERLANDS 4 5 6 art. 4701W/A GROUP S.P.A. Installatie wandmonitor art. 4701W/A art. 4714W/2 2 7 147 cm 3 NEDERLANDS 5 4 6 1 10 8 9 8 Simplebus2 grondplaat Grondplaat van de monitor voor de installatie van de monitor aan de muur of door middel van bureausteun art. 4712W (zie pag. 71) en maakt de aansluiting van de kabels van de installatie mogelijk. Voorzien van klemmen voor de aansluiting van de verdiepingsoproep (zie variant G pag. 111, voor de verbinding van een extra bel (zie SB2/D pag. 105) en voor het gebruik van de knop 1 van de monitor voor verschillend gebruik (zie variant E pag. 110). Er kunnen maximaal 3 grondplaten met dezelfde gebruikerscode in een installatie gemonteerd worden (zie pag. 98). Compatibel met Simplebus1 installaties. 3 1 4 Technische gegevens: 2 Afmetingen: 158x121x24 mm. 1. Connector voor de monitor. 2. Aansluitingen op de klemmen: 0 +20V aansluiting art. 1212/B. L L aansluiting buslijn. CFP CFP Ingang voor etagebel drukknop P1 C1 Voor een potentiaal vrij contact, knip de bruggen CV3 en CV4 door. S+ Suitgang voor extra bel. 3. CV5 Brug voor afsluiten videosignaal 4. JP1 jumper voor activering van passieve beeldoproep bij secundaire monitoren(zie variant F pag. 110). 5. CN2 steker voor programmering. 6. Dipswitches voor het programmeren van de gebruikerscode. 7. CV2, CV1, CV7 draadbruggen om extra monitoren te voeden door middel van art.1212/B (zie variant SB2/A3 pag. 101). 8. CV3, CV4 draadbruggen om knop 1 potentieel vrij te maken. 9. CV6 draadbrug voor de keuze van het systeem (Simplebus2 of Simplebus1). 10. JP2 jumper voor de keuze van het systeem (Simplebus2 of Simplebus1). MT SB2 01 70 1 3 1 4 2 2 MT SB2 01 Installatie van bureausteun art. 4712W voor monitor art. 4701W/A en art. 4700W 145 cm Installatie wandmonitor art. 4700W en art. 4700W/I NEDERLANDS Voormonitor monitor Per Art. art. 4700W 4700W 4700W/I 4700W/I art. 4514 4514 Art. voor soloAlleen per monitor Art.monitor 4700W art. 4700W art.4517 4517 Art. 1 4 3 1 2 2 4 1 3 2 71 MT SB2 01 GROUP S.P.A. Installatie halfinbouwmonitor art. 4700W met opbouwhuis art. 4704 147 cm 4 1 3 2 Art. 4704 Art. 4700W NEDERLANDS Hoe de monitor te verwijderen DEURTELEFOONS art. 2408W/A + C MI 5 6 3 4 + 1 2 MT SB2 01 72 Deurtelefoon Deurtelefoon van de serie Okay met afmetingen 85x223x65 mm. Voorzien van deuropeningsknop en knop om naar portiercentrale te bellen of voor het activeren van een speciaal relais (zie variant A pag. 108). Standaard uitgerust met verdiepingsoproep (zie variant B pag. 108). Er kunnen maximaal 3 deurtelefoons met dezelfde gebruikerscode in één installatie geïnstalleerd worden. Voor het instellen van de gebruikerscode zie “Programmering deurtelefoon art. 2408W/A, 2428W en grondplaat art. 4714W/2” op pag. 84. Alleen te gebruiken voor audio installaties. Technische gegevens: 1. Deuropeningsknop. 2. Knop voor het bellen naar de portierscentrale/ drukknop voor verschillende doeleinden (aansluitingen AB). 3. Aansluitingen op de klemmen: L L aansluiting buslijn. CFP CFP ingang etagebel. AB Aansluitingen drukknop voor diverse doeleinden. Voor een potentieelvrij NO contact, de draadbruggen CV1 en CV2 doorknippen. 4. Dipswitches voor het instellen van de gebruikerscode (zie pag. 85). 5. Trimmer voor het afstellen van het volume van de microfoon. 6. Trimmer voor het afstellen van het volume van de bel. MT SB2 01 ENTREEPANELEN art. 2410W In Simplebus2 installaties kunnen entreepanelen van de serie Powercom, Vandalcom en Logicom gebruikt worden. Voor Vandalcom en Logicom wordt er verwezen naar het technisch blad FT/SB/01 en naar de Catalogus 50. Audio luidsprekerunit Serie Powercom Deurtelefoon Deurtelefoon net als art. 2408W/A met extra LED en schakelaar voor Privacy of Dokter service (automatische opening van de deur na aanbellen). Zie technisch blad van het artikel voor de aansluiting op de installatie. + MI C 5 6 4 + 3 1 2 Deurtelefoon Deurtelefoon van de serie Okay met afmetingen 85x223x65 mm. Voorzien van deuropeningsknop en een drukknop voor de oproep van de portierscentrale of een andere functie (zie variant C pag. 109). Standaard uitgerust met etagebel (zie variant D pag. 109) en extra bel (zie SB2/D pag. 105). Deurtelefoon te gebruiken in gemixte audio-video installaties met voedingsmixer art. 4896 of in audio installaties wanneer er een extra bel nodig is. Er kunnen maximaal 3 deurtelefoons met dezelfde gebruikerscode in één systeem geïnstalleerd worden. Voor het installeren van extra deurtelefoons met dezelfde gebruikerscode zie de varianten SB2/A4 en SB2/A5 op pag. 102. Voor het instellen van de gebruikerscode zie “Programmering deurtelefoon art. 2408W/A, 2428W en grondplaat art. 4714W/2” op pag. 84. Technische gegevens: 1. Deuropeningsknop. 2. Knop voor het bellen naar de portierscentrale/ drukknop voor verschillende doeleinden (aansluitingen P1 C1). 3. Aansluitingen op de klemmen: L L aansluiting buslijn. CFP CFP ingang etagebel. P1 C1 Aansluitingen drukknop voor diverse doeleinden. Voor een potentieelvrij NO contact, de draadbruggen CV2 en CV3 doorknippen. S+ S- aansluitingen voor een extra bel. 4. Dipswitches voor het instellen van de gebruikerscode (zie pag. 85). 5. Trimmer voor het afstellen van het volume van de microfoon. 6. Trimmer voor het afstellen van het volume van de bel. Bestaat uit art. 3320 + art. 1602. Luidsprekerunits met aansluitblok en dubbele versterker, waterdichte luidspreker en electretmicrofoon. Het volume van de microfoon en van de luidspreker kan zowel vanaf de voorkant als vanaf de achterkant geregeld worden bij art.1602 (zie pag. 76). De microfoon kan verplaatst worden om het akoestisch rendement te verbeteren (zie pag. 76). Beldrukker van aluminiumlegering met naamplaatjes die er vanaf de voorkant uitgenomen kunnen worden. Compleet met microprocessor en dipswitches met 8 standen voor de programmering van de drukknoppen voor de gebruikers. Voor het programmeren van de drukknoppen zie pag. 86. Voeding 12V AC (gebruik art. 1195). Deuropeningsfunctie door middel van elektronische switch (3A alleen wisselstroom). Afmetingen 112x89.5x40 mm. Video luidsprekerunit Serie Powercom Bestaat uit art. 3321 + art. 4660. Verstelbare pinhole high sensitivity CCD 1/4” Z/W camera. Infraroodverlichting (6 LED’S). Compleet met aansluitblok en luidsprekerunit met dubbele versterker, waterdichte luidspreker en electretmicrofoon. Het volume van de microfoon en van de luidspreker kan zowel vanaf de voorkant als vanaf de achterkant geregeld worden bij art. 4660 (zie pag. 76). De microfoon kan verplaatst worden om het akoestisch rendement te verbeteren (zie pag. 76). Beldrukker van aluminiumlegering met naamplaatjes die er vanaf de voorkant uitgenomen kunnen worden. Compleet met microprocessor en dipswitches met 8 standen voor de programmering van de drukknoppen voor de gebruikers. Voor het programmeren van de drukknoppen zie pag. 86. Voeding 12V AC (gebruik art. 1195). Deuropeningsfunctie door middel van elektronische switch (3A alleen wisselstroom). Afmetingen 112x89.5x40 mm. 73 MT SB2 01 NEDERLANDS art. 2428W GROUP S.P.A. art. 3110 art. 3340 Inbouwdozen Beschikbaar voor 1, 2 en 3 modulen. Afmetingen enkele module 127x127x45 mm. NEDERLANDS art. 3311 Moduulframes compleet met sierrand Het frame is gemaakt van gegoten aluminium en door een speciale coating geschikt voor buitengebruik. Beschikbaar voor 1, 2 en 3 modulen in de kleuren grijs, wit, blauw en oranje. Afmetingen van de enkele module 125x125x15.5 mm. Digitale oproep module met naamindex Uitgevoerd met grafische LCD 128x64 dots, toetsenbord met 16 verlichte drukknoppen met blauwe LED. Er is ook een codeslot functie ingebouwd. Het is compleet met naamindex, welke 400 gebruikersnamen kan opslaan. Om een naam op te zoeken kan worden gescrolled d.m.v. 2 drukknoppen, of door het invoeren van de eerste letters. Ook kan direct de gebruikerscode worden ingetoetst. Als de juiste naam op het display verschijnt, kan eenvoudig op de beltoets gedrukt worden. Het programmeren is eenvoudig door het gebruik van een afstandbediening art. 1230 of met de software voor PC art. 1249. Afmetingen 112x180x40 mm. art. 3342 art. 3316 Opbouw behuizingen Behuizing van RVS. Beschikbaar voor 1, 2, 3, 4, 6 en 9 modulen. Voor bevestiging aan de wand, ook buiten. Handig als het niet mogelijk is de doos in te bouwen. Afmetingen van de enkele module 123x123x32.5 mm. art. 3323 Drukknopmodulen Beldrukker module uitgevoerd met microswitches en vervaardigd van een chroomaluminium legering. Blauwe LED voor de verlichting van de uitneembare naamkaders. Leverbaar met 4 of 6 drukknoppen. Afmetingen 112x89.5x40 mm. Voor het programmeren van de knoppen zie pag. 86. MT SB2 01 74 Naam index module Elektronische namenlijst met grafische display 128x64 dots. Kan maximaal 400 gebruikersnamen opslaan. Om een naam op te zoeken kan worden gescrolled d.m.v. 2 drukknoppen. Als de juiste naam op het display verschijnt, kan eenvoudig op de beltoets gedrukt worden. Het programmeren is eenvoudig door het gebruik van een afstandbediening art. 1230 of met de software voor PC art. 1249. Afmetingen: 112x89.5x40 mm. art. 3346 Bezetmodule Systeem bezet module. Compleet met een blauwe knipper LED voor het aangeven van de bezet status. Wordt geleverd met een blanco label, zodat een eigen tekst kan worden toegevoegd. Afmetingen: 112x89.5x38 mm MT SB2 01 Aanwijzingen voor het installeren van de audio en video entreepanelen Hoe meerdere dozen naast elkaar te plaatsen Bevestiging van het frame op de inbouwdoos Bevestiging van het frame op de opbouw behuizing Aansluiting 4-polige kabel Aansluitblok plaatsen of verwijderen 75 MT SB2 01 NEDERLANDS 160 - 165 cm Hoogte inbouwdoos GROUP S.P.A. Aanbrengen van de modulen Montage, aansluitingen en afstellingen audio-video systeem + C MI + NEDERLANDS Andere positie van de microfoon Montage / Demontage voorpanelen 3 4 2 5 1 Bevestiging sierrand Aanbrengen / verwijderen naamkaartjes 1 360˚ open 2 3 MT SB2 01 close 76 rla Ca ssi Ro MT SB2 01 Montage-instructies informatieve modulen art. 3326, art. 3344 en art. 3346 Aansluiting 4-polige kabel Aanbrengen van de module Verwijdering kaartjeshouder 10 NEDERLANDS 10 Kaartje aanbrengen/verwijderen 15 1 2 77 MT SB2 01 GROUP S.P.A. VOEDINGEN EN ACCESSOIRES art. 1122/A art. 1246 Transformator voor voedingsmixer Transformator 65VA. (T 1’on / 5’off). Primair: 230VAC Secundair: OUT1: 36VAC OUT2: 14VAC 1.5A 1A Relais Relais 12-24V DC-AC 5A voor algemeen gebruik. Direct aanstuurbaar vanaf de extra beluitgang van de grondplaat art. 4714W/2 of deurtelefoon art. 2428W. Afmetingen: 66x85x35 mm (4 DIN modulen). Aansluitklemmen: + voeding relais. C-NO-NC contacten relais. De transformator is uitgerust met interne PTC beveiliging. NEDERLANDS Afmetingen: 107x90x60 (8 DIN modulen). art. 1212/B art. 1224 Deurselector Voeding 12VAC. Afmetingen 66x85x35mm (4 DIN modulen). Aansluitklemmen: ~~* voeding 12VAC-20VDC. LS LS ingang buslijn secundaire buitenapparatuur. LP LP ingang buslijn primair entreepaneel. LM LM uitgang buslijn stamleiding. Voor het programmeren van de deurselector zie pag. 84. Voeding voor extra monitor Voeding 15VA Input: 230VAC Output: 0- 20VDC 700mA De transformator is uitgerust met interne PTC beveiliging. Afmetingen: 87x105x65 (5 DIN modulen). art. 1214/2 en art. 1216 art. 1214/2 art. 1216 Aftakblok en Afsluitblok Zie pag. 86 voor de configuratie van art. 1216 i.c.m. de gebruikte kabel. Aansluitklemmen: Lin Lin: ingang stamleiding. Lout Lout: uitgang stamleiding. LM LM: Aftakking naar de monitor/deurtelefoon. + +: klemmen voor aansluiting voeding voor compatibiliteit met Simplebus1 installaties. MT SB2 01 78 MT SB2 01 art. 1195 JP1 Transformator Transformator 60VA Primair 230VAC Secundair: OUT1: 0-12V 1.5A OUT2: 0-12V 1.5A De transformator is uitgerust met interne zekering. Afmetingen: 87x105x65 (5 DIN modulen). Art. 4896 moet gevoed worden door middel van transformator art.1246. Maak de aansluitingen van de installatie met uitgeschakelde stroom. Daar hij voorzien is van PTC beveiliging moet u, na een kortsluiting, de stroom er ongeveer een minuut lang af halen om hem weer te activeren. Schakel eerst het entreepaneel in en zet daarna spanning op de voedingsmixer art. 4896. Met deze voedingsmixer kan maximaal één monitor tegelijk gevoed worden en is in staat MAX 100 gebruikers te beheren. art. 4896 Aansluitklemmen: 1. Lin Lin aansluiting op de lijn afkomstig van entreepanele(e)l(en). Voedingsmixer De voedingsmixer art. 4896 bevindt zich in een behuizing van 12 DIN modulen. Afmetingen: 208x140x65 mm. Om toegang te kunnen verkrijgen tot de aansluitklemmen: de zijdeksels verwijderen zoals in de afbeelding getoond wordt. 2. 0V 36V aansluiting op de klemmen OUT1 van de transformator art. 1246. 0V 14V aansluiting op de klemmen OUT2 van de transformator art. 1246. 3. L1 L1 L2 L2 L3 L3 L4 L4 uitgang stamleiding 1. uitgang stamleiding 2. uitgang stamleiding 3. uitgang stamleiding 4. 4. Jumpers in te stellen naar gelang het totaal aantal gebruikers aangesloten op de voedingsmixer art. 4896. JP1 en JP2 in positie 3 voor installaties met van 0 tot 15 gebruikers. JP1 en JP2 in positie 2 voor installaties met van 16 tot 35 gebruikers. JP1 en JP2 in positie 1 voor installaties met van 36 tot 100 gebruikers. JP1 - JP2 2 4 1 1 3 2 3 4 79 MT SB2 01 NEDERLANDS JP2 GROUP S.P.A. art. 4577 Comelit Simplebus2 kabel Speciale kabel voor Simplebus2 installaties: bestaat uit een rode en zwarte getwiste ader 1 mm2. Leverbaar in rollen van 100 m. en haspels van 500 m. art. 4833/A Buslijnversterker Versterker voor Simplebus1 video-installaties. Regenereert het videosignaal van de buslijn. Voeding: 12V AC of 20V DC. Alleen te monteren in de installatie vóór de voedingsmixer. Afmetingen: 66x85x35 mm (4 DIN modulen). NEDERLANDS Aansluitklemmen: Lin Lin: ingang stamleiding. Lout Lout: uitgang stamleiding. ~+ ~-: voeding module. art. 1254 Relais voor verschillende toepassingen Voeding 12VAC, 20VDC. Vermogen relais: 10A. Dit relais kan worden toegepast voor: • Extra bel. • Aansturing relais door gebruiker in installaties zonder portiercentrale. • Verlichting trappenhuis. • Secundaire deuropener. Voor installatie en verschillende varianten zie documentatie van art. 1254. MT SB2 01 80 art. 4834/2 Buslijnverdeler Verdeler voor Simplebus video-installatie. Maakt het mogelijk het signaal naar 4 buslijnen te verdelen. Alleen installeren in de installatie vóór de voedingsmixer. Afmetingen: 66x85x35 mm (4 DIN modulen). Aansluitklemmen: Lin Lin: ingang buslijn. L1 L1: uitgang buslijn 1. L2 L2: uitgang buslijn 2. L3 L3: uitgang buslijn 3 (weerstand afknippen alvorens de draad aan te brengen). L4 L4: uitgang buslijn 4 (weerstand afknippen alvorens de draad aan te brengen). MT SB2 01 Installatievoorschriften voor video deurtelefoons Plaats de draden van de stamleiding niet in de buurt van voedingskabels (220/380V). De aftakkingen vanaf de stamleiding naar de gebruiker dienen gemaakt te worden met het aftakblokje art. 1214/2, welke standaard wordt meegeleverd bij de grondplaat 4714W/2. Wanneer er sprake is van een gemixte installatie dient voor iedere deurtelefoon art. 2428W een aftakblokje art. 1214/2 te worden aangeschaft. Sluit iedere stamleiding af met het bij de voedingsmixer art. 4896 en cameramodule art. 4660 meegeleverde afsluitblokje. Afhankelijk van de gebruikte kabel dienen de afsluitblokjes ingesteld te worden volgens de tabel op pag. 86. Afhankelijk van de kabel die voor de stamleiding gebruikt is, kunt u de maximale afstand bepalen tussen de voedingsmixer art. 4896 en de verste monitor en tussen het aftakblokje art. 1214/2 en de verste monitor. Afhankelijk van de gebruikte kabel kunt u de maximale afstand bepalen tussen het video entreepaneel en de voedingsmixer art. 4896. In de tabel op pag. 82 worden de verschillende kabels vermeld met de daarbij behorende maximale afstanden. Iedere mixervoeding art. 4896 kan MAX. 4 stamleidingen beheren, zie variant SB2/B op pag. 103. Bij installatie met hoofdingangen en secundaire ingangen (zie schema SB2V/EN/112 pag. 97) dienen de buslijnverdeler art. 4834/2 en de deurselector art. 1224 gebruikt te worden. Bij één entree kunnen er maximaal 4 mixervoedingen art. 4896 worden aangesloten op de buslijnverdeler art. 4834/2 (zie schema SB2V/012 pag. 94). Op iedere buslijnverdeler art. 4834/2 kunnen MAX. 4 aftakkingen worden aangesloten: als er meer aftakkingen nodig zijn (max. 16) dienen er twee buslijnverdelers art. 4834/2 in cascade te worden aangesloten. De uitgang van de eerste buslijnverdeler dient te worden versterkt door de versterker 4833/A (zie variant SB2/C pag. 104). Er kunnen MAX. 2 buslijnverdelers art. 4834/2 in cascade geschakeld worden. Het MAX. aantal gebruikers dat op één voedingsmixer art. 4896 aangesloten kan worden is 100 of ze nu op één enkele stamleiding of op meerdere stamleidingen verdeeld zijn (bijv.: 100 gebruikers op één stamleiding of 25 gebruikers op vier stamleidingen). Er kunnen maximaal 25 monitors cascade geschakeld worden bij iedere stamleiding (zie variant SB2/G pag. 106); in dit geval wordt er, voor de MAX. afstand tussen het entreepaneel en de laatste monitor van de cascadeschakeling, verwezen naar de tabel op pag. 82 kolom A. Er kunnen meerdere monitors met dezelfde gebruikerscode (MAX. 3) in cascade worden geschakeld na aftakking van de stamleiding volgens de varianten SB2/A1-A2-A3-A4-A5 (pag. 99-100-101-102). De deurtelefoons art. 2428W met dezelfde gebruikerscode van de monitor dienen van de stamleiding afgetakt worden door middel van art. 1214/2. De voedingsmixer art. 4896 voedt, telkens als er gebeld wordt, één enkele monitor en dus is het, bij installaties met meerdere monitoren met dezelfde gebruikerscode, nodig de extra monitoren als secundair in te stellen of iedere extra monitor apart te voeden door middel van art.1212/B (zie pag. 99-100-101). Stel de grondplaat art. 4714W/2 in d.m.v. de draadbruggen en jumpers, zoals aangeduid in de varianten van de basisschema's SB2/A1-A2-A3 naar gelang de gewenste configuratie. De camera's van de entreepanelen mogen niet op direct licht gericht worden (bijv. lampen, zonlicht, reflecterende oppervlakken, enz.). 81 MT SB2 01 NEDERLANDS INSTALLATIEVOORSCHRIFTEN GROUP S.P.A. Maximale afstanden en eigenschappen van de aders De monitoren worden aangesloten op een omkeerbare buslijn. Indien er kabels worden gebruikt die niet in de tabel worden beschreven, kunnen wij niet garanderen over welke afstand deze kabel een goed videosignaal kan behouden. Gebruik dus alleen kabels die in de onderstaande tabel worden omschreven. MAX. afstand tussen voedingsmixer art. 4896 en binnentoestel. NEDERLANDS Type kabel MAX. afstand tussen entreepaneel en voedingsmixer art. 4896. MAX. afstand tussen entreepaneel en art. 4833/A. MAX. afstand tussen art. 4833/A en voedingsmixer art. 4896. MAX. afstand tussen entreepaneel en voedingsmixer of versterker art. 4833/A met art. 4834/2 MAX. afstand tussen aftakblokje art.1214/2 en binnentoestel. A B C D E H Comelit kabel art. 4577 doorsn. 1 mm2 (Ø 1.2 mm) 200 m 200 m 200 m 200 m 150 m 60 m Tweeaderige kabel doorsn. 1.5mm2 (Ø 1.4 mm)** 150 m 100 m 100 m 100 m 80 m 40 m Getwiste en afgeschermde kabel doorsn. 1 mm2 (Ø 1.2 mm)* 120 m 80 m 80 m 80 m 50 m 30 m Getwist aderpaar doorsn. 0.28 mm2 (Ø 0.6 mm) * 100 m 150 m 150 m 150 m 100 m 40 m Kabel UTP5 cat 5 AWG 24 doorsn. 0.2 mm2 (Ø 0.5 mm)* 80 m 150 m 150 m 150 m 100 m 40 m 120 m 100 m 100 m 100 m 80 m 40 m Tweeaderige kabel doorsn. 0.5 mm2 (Ø 0.8 mm)** * Bij meeraderige kabel (aders per twee getwist) heeft het de voorkeur één aderpaar te gebruiken voor het systeem (buslijn). Indien het noodzakelijk is spanningsverlies te voorkomen, in het geval van lange afstanden, is het mogelijk een aderpaar samen te nemen voor één busader. ** Bij meeraderige kabel (aders per twee getwist) is het noodzakelijk slechts twee aders te gebruiken en wordt geadviseerd de aders niet dubbel te nemen voor aderdoorsnede-compensatie. Maximale afstanden voor de voedingsaders van een extra monitor en de buitenapparatuur Doorsnede van de ader MAX. afstand tussen transformator art. 1195 en entreepaneel. MAX. afstand tussen voeding art. 1212/B en monitor. F G (Ø 0.6 mm) 4m 10 m 0.5 mm 2 (Ø 0.8 mm) 10 m 25 m 1 mm 2 (Ø 1.2 mm) 20 m 50 m 1.5 mm 2 (Ø 1.4 mm) 30 m 100 m 2 mm 2 (Ø 1.6 mm) 40 m 150 m 0.28 mm 2 MT SB2 01 82 MT SB2 01 NEDERLANDS Afbeeldingen voor de afstanden 83 MT SB2 01 GROUP S.P.A. CONFIGURATIE VAN DE APPARATUUR NEDERLANDS 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Programmering deurtelefoon art. 2408W/A, 2410W, 2428W en grondplaat art. 4714W/2 • Iedere deurtelefoon of grondplaat van het systeem wordt ingesteld met een eigen code; deze code moet ingesteld worden door middel van de dipswitches in de deurtelefoon of op de grondplaat van de monitor (zie afbeeldingen). • De gebruikerscode moet ingesteld worden volgens de tabel op pag. 85. • Deze codering kan altijd worden ingesteld, ook zónder spanning op het systeem. Programmering schakelapparaat art. 1224 • Voorbeeld van het instellen van een deurselektor art. 1224 van portiek A, minimaal nummer 1, maximaal nummer 10. X MA N MI O1 N 2 3 4 5 6 7 O1 8 N 2 3 4 5 6 7 8 PORTIEK SCALA A A NR. N°1÷10. 1÷10 4700 W 4700 W/I 4701 W/A 4700 W 4700 W/I 4701 W/A 4700 W 4700 W/I 4701 W/A 4700 W 4700 W/I 4701 W/A PORTIEK SCALA B B N° N° 11÷20. 11÷20 HOOFDINGANG VANDAL NR. N° 1÷20. PORTA PRINCIPALE 1÷20. • Elke selector is uitgevoerd met 2 dipswitches met ieder 8 schakelaars (zie afbeelding). Met de twee dipswitches kan de minimale MIN en de maximale MAX range van codes worden ingesteld op de selector. MT SB2 01 84 • Let op: de MIN en de MAX dipswitches vertegenwoordigen de laagste en hoogste code die op deze buslijn kan worden aangesloten. • Om de waarden in te stellen verwijzen wij naar pag. 85. • Bij meerdere selektors mogen de codes elkaar niet overlappen. MT SB2 01 Programmeringtabel van de dipswitches dipswitches op ON 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 1 2 1,2 3 1,3 2,3 1,2,3 4 1,4 2,4 1,2,4 3,4 1,3,4 2,3,4 1,2,3,4 5 1,5 2,5 1,2,5 3,5 1,3,5 2,3,5 1,2,3,5 4,5 1,4,5 2,4,5 1,2,4,5 3,4,5 1,3,4,5 2,3,4,5 1,2,3,4,5 6 1,6 2,6 1,2,6 3,6 1,3,6 2,3,6 1,2,3,6 4,6 1,4,6 2,4,6 1,2,4,6 3,4,6 1,3,4,6 2,3,4,6 1,2,3,4,6 5,6 1,5,6 2,5,6 1,2,5,6 3,5,6 1,3,5,6 2,3,5,6 1,2,3,5,6 4,5,6 1,4,5,6 2,4,5,6 1,2,4,5,6 3,4,5,6 Naam gebruiker Gebruik. dipswitches op ON 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 1,3,4,5,6 2,3,4,5,6 1,2,3,4,5,6 7 1,7 2,7 1,2,7 3,7 1,3,7 2,3,7 1,2,3,7 4,7 1,4,7 2,4,7 1,2,4,7 3,4,7 1,3,4,7 2,3,4,7 1,2,3,4,7 5,7 1,5,7 2,5,7 1,2,5,7 3,5,7 1,3,5,7 2,3,5,7 1,2,3,5,7 4,5,7 1,4,5,7 2,4,5,7 1,2,4,5,7 3,4,5,7 1,3,4,5,7 2,3,4,5,7 1,2,3,4,5,7 6,7 1,6,7 2,6,7 1,2,6,7 3,6,7 1,3,6,7 2,3,6,7 1,2,3,6,7 4,6,7 1,4,6,7 2,4,6,7 1,2,4,6,7 3,4,6,7 1,3,4,6,7 2,3,4,6,7 1,2,3,4,6,7 5,6,7 1,5,6,7 2,5,6,7 1,2,5,6,7 3,5,6,7 1,3,5,6,7 2,3,5,6,7 1,2,3,5,6,7 4,5,6,7 Naam gebruiker Gebruik. dipswitches op ON 121 1,4,5,6,7 122 2,4,5,6,7 123 1,2,4,5,6,7 124 3,4,5,6,7 125 1,3,4,5,6,7 126 2,3,4,5,6,7 127 1,2,3,4,5,6,7 128 8 129 1,8 130 2,8 131 1,2,8 132 3,8 133 1,3,8 134 2,3,8 135 1,2,3,8 136 4,8 137 1,4,8 138 2,4,8 139 1,2,4,8 140 3,4,8 141 1,3,4,8 142 2,3,4,8 143 1,2,3,4,8 144 5,8 145 1,5,8 146 2,5,8 147 1,2,5,8 148 3,5,8 149 1,3,5,8 150 2,3,5,8 151 1,2,3,5,8 152 4,5,8 153 1,4,5,8 154 2,4,5,8 155 1,2,4,5,8 156 3,4,5,8 157 1,3,4,5,8 158 2,3,4,5,8 159 1,2,3,4,5,8 160 6,8 161 1,6,8 162 2,6,8 163 1,2,6,8 164 3,6,8 165 1,3,6,8 166 2,3,6,8 167 1,2,3,6,8 168 4,6,8 169 1,4,6,8 170 2,4,6,8 171 1,2,4,6,8 172 3,4,6,8 173 1,3,4,6,8 174 2,3,4,6,8 175 1,2,3,4,6,8 176 5,6,8 177 1,5,6,8 178 2,5,6,8 179 1,2,5,6,8 180 3,5,6,8 Naam gebruiker Gebruik. dipswitches op ON Naam gebruiker 181 1,3,5,6,8 182 2,3,5,6,8 183 1,2,3,5,6,8 184 4,5,6,8 185 1,4,5,6,8 186 2,4,5,6,8 187 1,2,4,5,6,8 188 3,4,5,6,8 189 1,3,4,5,6,8 190 2,3,4,5,6,8 191 1,2,3,4,5,6,8 192 7,8 193 1,7,8 194 2,7,8 195 1,2,7,8 196 3,7,8 197 1,3,7,8 198 2,3,7,8 199 1,2,3,7,8 200 4,7,8 201 1,4,7,8 202 2,4,7,8 203 1,2,4,7,8 204 3,4,7,8 205 1,3,4,7,8 206 2,3,4,7,8 207 1,2,3,4,7,8 208 5,7,8 209 1,5,7,8 210 2,5,7,8 211 1,2,5,7,8 212 3,5,7,8 213 1,3,5,7,8 214 2,3,5,7,8 215 1,2,3,5,7,8 216 4,5,7,8 217 1,4,5,7,8 218 2,4,5,7,8 219 1,2,4,5,7,8 220 3,4,5,7,8 221 1,3,4,5,7,8 222 2,3,4,5,7,8 223 1,2,3,4,5,7,8 224 6,7,8 225 1,6,7,8 226 2,6,7,8 227 1,2,6,7,8 228 3,6,7,8 229 1,3,6,7,8 230 2,3,6,7,8 231 1,2,3,6,7,8 232 4,6,7,8 233 1,4,6,7,8 234 2,4,6,7,8 235 1,2,4,6,7,8 236 3,4,6,7,8 237 1,3,4,6,7,8 238 2,3,4,6,7,8 239 1,2,3,4,6,7,8 *240 5,6,7,8 NEDERLANDS Gebruik. *N.B.: de code 240 is gereserveerd voor de portierscentrale VOORBEELD instelling code 200. 85 MT SB2 01 GROUP S.P.A. fig. 1 6 7 8 2 Tweeaderige kabel doorsn. 1.5 mm2 (Ø 1.4 mm) 1 1 Getwist aderpaar doorsn. 0.28 mm2 (Ø 0.6 mm) Kabel UTP5 cat 5 AWG 24 doorsn. 0.2 mm2 (Ø 0.5 mm) 2 Tweeaderige kabel doorsn. 0.5 mm2 (Ø 0.8 mm) 2 86 5 fig. 3 Comelit kabel art. 4577 doorsn. 1 mm2 (Ø 1.2 mm) MT SB2 01 4 fig. 2 Instelling art. 1216 Getwiste en afgeschermde kabel doorsn. 1 mm2 (Ø 1.2 mm) 3 art. 3309 Tabel met de instellingen van art. 1216 behorend bij de gebruikte bekabeling Type kabel 2 1. Verbind de drukknopmodulen 3323/4 en 3323/6 met de modulen 4660 of 1602 d.m.v. de meegeleverde verbindingen. Steek de modulen 3323/4 en 3323/6 in de bijbehorende aansluitblokken (zie figuur 1). 2. Sluit de voeding aan op de klemmen ~ ~ van de module 4660 of 1602 en maak daarna een draadbrug tussen de klemmen PR en – en verzet de doorverbinding (vanaf P/O) van OCC naar V+ (zie figuur 2). Verbind het aansluitblok met de modulen 4660 of 1602 zoals afgebeeld. Attentie: de modulen 3323/4 en 3323/6 dienen al gemonteerd te zijn, voordat met de programmering wordt gestart (zie figuur 2). OPMERKING: er is een speciale programmeerkabel art. 3309 leverbaar als accessoire voor het verbinden van het aansluitblok en de module 4660 of 1602 tijdens het programmeren (zie figuur 3). 3. Zet de dipswitch aan de achterzijde van de luidsprekermoduul op dezelfde code als die op de corresponderende huistelefoon of monitor ingesteld is volgens de tabel op pag. 85. 4. Druk nu op de drukknop die op deze code moet worden geprogrammeerd. Als de programmering wordt opgeslagen, wordt dit bevestigd door een bevestigingstoon. 5. Zet na de programmering de doorverbindingen weer in de oorspronkelijke posities, PR op PR en P/O op OCC. Instellen als hoofdpaneel of secundaire ingang. De modulen 4660 of 1602 functioneren normaal als hoofdentree (bezet signaal gedurende een ingestelde tijd). Om deze in te stellen als secondair entreepaneel (bezet signaal als de buslijn in gebruik is) dienen alle dipswitches op “ON” ingesteld te worden. O N 1 NEDERLANDS Programmering beldrukkers met audio art. 1602 en video art.4660 en modulen art. 3323/4 en 3323/6 MT SB2 01 • De bezoeker drukt op de beldrukker en activeert daarmee de beltoon van de binnentoestellen. • Het entreepaneel laat het belgeluid horen waarmee bevestigd wordt dat er gebeld is; als u, in een installatie met meerdere ingangen, het bevestigingsgeluid niet hoort, dan betekent dit dat het systeem in communicatie is met een ander entreepaneel dat in dezelfde gebruikersgroep geïnstalleerd is. Als de bezetmodule art. 3346 geïnstalleerd is, wacht dan totdat de LED’s in de module uitgaan alvorens opnieuw te bellen. Als het art. 3340 geïnstalleerd is, dan wordt er op het display aangegeven dat de installatie in gesprek is. • Als de hoorn wordt opgenomen kan er een gesprek plaatsvinden met het entreepaneel. • De toets aangeduid met het symbool van de sleutel activeert gedurende ongeveer 2 seconden het elektrische slot buiten. • Wanneer in een video-intercom systeem wordt aangebeld, gaan de infrarood LED’s bij de camera aan (onzichtbaar voor het menselijk oog) om de bezoeker te verlichten; het beeld blijft gedurende ongeveer 90 seconden lang op de monitor • Voor de afstelling van het volume van de microfoon en het volume van de beltoon van de deurtelefoons zie pag. 72 en 73. • Voor de afstelling van het volume van de bel van de monitoren zie pag. 68 en 69. • Voor de afstelling van het audio volume buiten zie pag. 10. • Voor het activeren van de beeldoproep dient knop 2 langer dan 2 seconden ingedrukt gehouden worden (zie variant H pag. 111). Als deze instelling is gemaakt, wordt dit bevestigd door een toon in de hoorn. • De beeldoproep vindt plaats (als de functie geactiveerd is) door knop 2 in te drukken. Als er twee entreepanelen met camera geïnstalleerd zijn, kunt u, door knop 2 voor de beeldoproep van de monitor nogmaals in te drukken, eerst het beeld van de ene ingang en dan van de andere ingang verkrijgen (afwisselingfunctie tussen de twee ingangen). • De helderheid van de monitor kan worden veranderd door het stelwieltje aan de onderkant te gebruiken. • Het volume van de bel kan worden ingesteld door de schakelaar aan de onderkant van de monitor te gebruiken. • Met de optionele kaart art. 4703 kan de Privacy functie ingesteld worden. Door de knop 4 van de monitor langer dan 2 seconden ingedrukt te houden gaat de LED branden die aangeeft dat de monitor in de Privacy modus is ingesteld (zie variant I pag 112). In de privacy modus belt de monitor niet, maar er komt wel beeld; u heeft toch de mogelijkheid met buiten te praten nadat er gebeld is. • Wanneer de hoorn er binnen opgelegd wordt, heeft u nog enkele seconden de tijd om het gesprek met buiten te hervatten. Vanaf het moment dat de hoorn er opgelegd is verlopen er nog enkele seconden voordat het beeld van de monitor verdwijnt. • De als primair ingestelde monitor (fabrieksinstelling van de grondplaat art. 4714W/2) gaat aan als er gebeld wordt en bij beeldoproep, ook als dit een extra monitor is met dezelfde gebruikerscode en een eigen voeding. • De als secundair ingestelde monitor (zie variant SB2/A1-A2) geeft geen beeld als er gebeld wordt, maar kan aangezet worden door de knop 2 in te drukken (passieve beeldoproep). Bij deze monitor is actieve beeldoproep niet mogelijk (oproep zonder dat er is aangebeld). • Monitoren en deurtelefoons met dezelfde gebruikerscode bellen allemaal tegelijk (onafhankelijk van het feit of ze primair of secundair zijn) als er vanaf buiten wordt gebeld, maar ook als er een etagebel is aangesloten. 87 MT SB2 01 NEDERLANDS WERKING ITALIANO GROUP S.P.A. SCHEMI DI COLLEGAMENTO WIRING DIAGRAMS SCHEMAS DE CONNEXION AANSLUITSCHEMA’S SBC/01L I Impianto 1 porta audio Serie Logicom. GB System with 1 Logicom Series audio entrance. NEDERLANDS FRANÇAIS ENGLISH F Installation avec 1 porte audio Série Logicom. NL Installatie 1 audio entreepaneel Serie Logicom. A SBC/01 I Impianto 1 porta audio Serie Powercom. GB System with 1 Powercom Series audio entrance. F Installation avec 1 porte audio Série Powercom. NL Installatie 1 audio entreepaneel Serie Powercom. MT SB2 01 88 MT SB2 01 ITALIANO SBC/02L I Impianto 1 porta audio digitale Serie Logicom 3040 (3070) – 3042 (3072). GB System with 1 Logicom Series digital audio entrance 3040 (3070) – 3042 (3072). F Installation avec 1 porte audio numérique Série Logicom 3040 (3070) – 3042 (3072). NEDERLANDS FRANÇAIS ENGLISH NL Installatie 1 digitale audio entreepaneel Serie Logicom 3040 (3070) – 3042 (3072) SBC/02 I Impianto 2 porte audio digitali Serie Powercom 3340 - 3342. GB System with 2 Powercom Series digital audio entrances 3340 - 3342. A F Installation avec 2 portes audio numériques Série Powercom 3340 - 3342. NL Installatie 2 digitale audio entreepanelen Serie Powercom 3340 - 3342. 89 MT SB2 01 GROUP S.P.A. GB System with 1 Logicom Series video entrance. F Installation avec 1 porte vidéo Série Logicom. NL Installatie 1 video entreepaneel Serie Logicom. A NEDERLANDS FRANÇAIS ENGLISH ITALIANO SB2V/01L I Impianto 1 porta video Serie Logicom. MT SB2 01 90 MT SB2 01 ITALIANO SB2V/01 I Impianto 1 porta video Serie Powercom. GB System with 1 Powercom Series video entrance. F Installation avec 1 porte vidéo Série Powercom. A NEDERLANDS FRANÇAIS ENGLISH NL Installatie 1 video entreepaneel Serie Powercom. 91 MT SB2 01 GROUP S.P.A. GB System with 2 Logicom Series video entrances. F Installation avec 2 portes vidéo Série Logicom. NL Installatie 2 video entreepanelen Serie Logicom. A NEDERLANDS FRANÇAIS ENGLISH ITALIANO SB2V/03L I Impianto 2 porte video Serie Logicom. MT SB2 01 92 MT SB2 01 ITALIANO SB2V/03 I Impianto 2 porte video Serie Powercom. GB System with 2 Powercom Series video entrances. F Installation avec 2 portes vidéo Série Powercom. A NEDERLANDS FRANÇAIS ENGLISH NL Installatie 2 video entreepanelen Serie Powercom. 93 MT SB2 01 GROUP S.P.A. GB System with 1 Powercom Series video entrance and MAX 4 Mixers-power supplies Art. 4896. F Installation avec 1 porte vidéo Série Powercom et MAX 4 mélangeurs-alimentations Art. 4896. 94 VERWIJDER ALLEEN DE WEERSTAND ALS DE UITGANG GEBRUIKT WORDT. COUPER SEULEMENT LA RESISTANCE DE LA SORTIE UTILISEE TAGLIARE SOLO LA RESISTENZA DELL’USCITA UTILIZZATA. FRANÇAIS NEDERLANDS A MT SB2 01 ONLY CUT THE RESISTANCE OF THE OUTPUT USED. NL Installatie met 1 video entreepaneel Serie Powercom en MAX. 4 voedingmixers art. 4896. ENGLISH ITALIANO SB2V/012 I Impianto con 1 porta video Serie Powercom e max 4 Miscelatori-alimentatori Art. 4896. MT SB2 01 ITALIANO SB2V/013 I Impianto con 2 porte video e centralino di portineria Art. 1998. GB System with 2 video entrances and porter switchboard Art. 1998. F Installation avec 2 portes vidéo et un HP-micro Art. 1998. A NEDERLANDS FRANÇAIS ENGLISH NL Installatie met 2 video entreepanelen en portierscentrale art. 1998. 95 MT SB2 01 GROUP S.P.A. GB System with 1 main video entrance and MAX 4 Logicom series secondary videos. F Installation avec 1 entrée principale vidéo MAX 4 secondaires vidéo série Logicom. NL Installatie 1 video hoofdentreepaneel met MAX. 4 secundaire video entreepanelen serie Logicom. MT SB2 01 96 VERWIJDER ALLEEN DE WEERSTAND ALS DE UITGANG GEBRUIKT WORDT. COUPER SEULEMENT LA RESISTANCE DE LA SORTIE UTILISEE ONLY CUT THE RESISTANCE OF THE OUTPUT USED. TAGLIARE SOLO LA RESISTENZA DELL’USCITA UTILIZZATA. A NEDERLANDS FRANÇAIS ENGLISH ITALIANO SB2V/EN/112L I Impianto 1 ingresso principale video max 4 secondari video serie Logicom. MT SB2 01 ITALIANO SB2V/EN/112 I Impianto 1 ingresso principale video max 4 secondari video serie Powercom. GB System with 1 main video entrance and MAX 4 Powercom series secondary videos. F Installation avec 1 entrée principale vidéo MAX 4 secondaires vidéo série Powercom. A NEDERLANDS FRANÇAIS ENGLISH NL Installatie 1 video hoofd-entreepaneel met MAX. 4 secundaire video entreepanelen serie Powercom. 97 MT SB2 01 GROUP S.P.A. VARIANTI AGLI SCHEMI BASE DI COLLEGAMENTO F VARIANTES AUX SCHEMAS DE CONNEXION DE BASE Collegamento di più utenti con lo stesso codice utente (MAX 3). E’ possibile avere non più di 3 posti interni con lo stesso codice utente. I monitor con lo stesso codice utente devono stare sulla stessa diramazione di montante cioè sulla stessa uscita L1L1 o L2L2 o L3L3 o L4L4 del Miscelatore-alimentatore Art. 4896. Agendo su JP1 della staffa Art. 4714W/2 i posti interni video possono essere impostati come Principali (si accende su chiamata e su autoaccensione) o come Secondari (non si accende su chiamata ma su richiesta video premendo il pulsante 2). A seconda della tipologia di impianto bisogna impostare le staffe dei monitor supplementari come di seguito descritto. Connexion de plusieurs usagers ayant le même code usager (MAX 3). Possibilité d’avoir au maximum 3 postes intérieurs avec le même code usager. Les moniteurs ayant le même code usager doivent se trouver sur la même dérivation du montant, c’est-à-dire sur la même sortie L1L1 ou L2L2 ou L3L3 ou L4L4 du mélangeur-alimentation Art. 4896. En intervenant sur JP1 de la bride Art. 4714W/2, les postes intérieurs vidéo peuvent être programmés comme Principaux (ils se branchent à l’appel et au autoallumage) ou comme Secondaires (ils ne se branchent pas à l’appel mais à la demande vidéo en appuyant sur le bouton 2). Selon le type d’installation, les brides des moniteurs additionnels doivent être programmées de la manière décrite ci-dessous. GB VARIANTS TO THE BASIC WIRING DIAGRAMS NL VARIANTEN VAN DE STANDAARD AANSLUITSCHEMA’S Connection of several users with the same user code (MAX 3). It is possible to have no more than 3 internal units with the same user code. The monitors with the same user code must be on the same riser branch, i.e. on the same L1L1 or L2L2 or L3L3 or L4L4 output of the Mixer-power supply Art. 4896. Working on JP1 of bracket Art. 4714W/2, the internal video units can be set as Main (they light up on a call and on Self-ignition) or as Secondary (they do not light up on a call but on video request by pressing push-button 2). According to the type of system, the additional monitor brackets must be set as described below. Aansluiting van meerdere gebruikers met dezelfde gebruikerscode (MAX. 3). Er kunnen maximaal 3 binnentoestellen met dezelfde gebruikerscode zijn. De monitoren met dezelfde gebruikerscode dienen op dezelfde stamleiding aangesloten te zijn d.w.z. op dezelfde uitgang L1L1 of L2L2 of L3L3 of L4L4 van de mixervoeding art. 4896. Met behulp van JP1 op de grondplaat art. 4714W/2 kunnen de monitoren ingesteld worden als Primair (gaat aan als er gebeld wordt en bij beeldoproep) of als Secundair (gaat niet aan als er gebeld wordt, maar het beeld kan opgeroepen worden door knop 2 in te drukken). Naar gelang het type installatie dienen de grondplaten van de extra monitoren ingesteld te worden zoals als volgt beschreven wordt. A NEDERLANDS FRANÇAIS ENGLISH ITALIANO I MT SB2 01 98 MT SB2 01 • Accensione del solo monitor Principale su chiamata. • Accensione su pressione del pulsante2 dei monitor Secondari dopo chiamata (Richiesta Video). • Suoneria su tutti i monitor. • Possibilità di eseguire Autoaccensione sul monitor Principale. GB • Ignition up only of Main monitor on a call. • Lighting up on push-button 2 of the Secondary monitors being pressed after a call (Video request). • Call tone on all the monitors. • Possibility of carrying out Self-ignition on the Main monitor. F • Branchement seulement du moniteur Principal sur appel. • Branchement à l’appui sur le bouton 2 des moniteurs Secondaires après l’appel (Demande Vidéo). • Sonnerie sur tous les moniteurs. • Possibilité d’effectuer un Autoallumage sur le moniteur Principal. NL • Alleen de hoofdmonitor gaat aan als er gebeld wordt. • De secundaire monitoren gaan aan nadat er gebeld is en knop 2 is ingedrukt (passieve beeldoproep). • Beltoon op alle monitors. • Mogelijkheid tot beeldoproep van de hoofdmonitor. MONITOR SECONDARIO SECONDARY MONITOR MONITEUR SECONDAIRE SECUNDAIRE MONITOR A I FRANÇAIS F Connexion en dérivation de moniteurs ayant le même code usager alimentés à partir du montant. NL Aftakverbinding van monitoren met dezelfde gebruikerscode gevoed door de stamleiding. NEDERLANDS GB Branched connection of monitors with the same user code supplied by a riser. ENGLISH ITALIANO SB2/A1 I Collegamento in derivazione di monitor con lo stesso codice utente alimentati da montante. MONITOR SECONDARIO SECONDARY MONITOR MONITEUR SECONDAIRE SECUNDAIRE MONITOR MONITOR PRINCIPALE MAIN MONITOR MONITEUR PRINCIPAL HOOFDMONITOR 99 MT SB2 01 GROUP S.P.A. ITALIANO SB2/A2 I Collegamento in cascata di monitor con lo stesso codice utente alimentati da montante. GB Connection in cascade of monitors with the same user code supplied from a riser. F Connexion en cascade de moniteurs ayant le même code usager alimentés à partir du montant. NL Cascadeschakeling van monitoren met dezelfde gebruikerscode afgetakt van de stamleiding. GB • Accensione su chiamata del solo monitor Principale. • Accensione su pressione del pulsante 2 dei monitor Secondari dopo chiamata (Richiesta Video). • Suoneria su tutti i monitor. • Possibilità di eseguire Autoaccensione sul monitor Principale. F • Branchement à l’appel seulement du moniteur Principal. • Branchement à l’appui sur le bouton 2 des moniteurs Secondaires après l’appel (Demande Vidéo). • Sonnerie sur tous les moniteurs. • Possibilité d’effectuer un Autoallumage sur le moniteur Principal. • Ignition up on a call of Main monitor only. • Ignition up on pressing push-button 2 of the Secondary monitors after a call (Video request). • Call tone on all the monitors. • Possibility of carrying out Self-ignition on the Main monitor. NL • Alleen de hoofdmonitor gaat aan als er gebeld wordt. • De secundaire monitoren gaan aan nadat er gebeld is en knop 2 is ingedrukt (passieve beeldoproep). • Beltoon op alle monitoren. • Mogelijkheid tot beeldoproep van de hoofdmonitor. A NEDERLANDS FRANÇAIS ENGLISH I MONITOR PRINCIPALE MAIN MONITOR MONITEUR PRINCIPAL HOOFDMONITOR MT SB2 01 100 MONITOR SECONDARIO SECONDARY MONITOR MONITEUR SECONDAIRE SECUNDAIRE MONITOR MONITOR SECONDARIO SECONDARY MONITOR MONITEUR SECONDAIRE SECUNDAIRE MONITOR MT SB2 01 F Connexion en cascade de moniteurs ayant le même code usager alimentés séparément. NL Cascadeschakeling van monitoren met dezelfde gebruikerscode afzonderlijk gevoed. • Accensione simultanea di tutti i monitor sia su chiamata che su autoaccensione. • Autoaccensione su pressione del pulsante 2 del monitor. • Attenzione: togliendo il monitor Principale alimentato da montante non si ha più segnale video nemmeno sugli altri due monitor. GB • Simultaneous ignition up of all the monitors both on a call and on self-ignition. • Self-ignition on pressing push-button 2 of the monitor. • Warning: by removing the Main monitor supplied from a riser, there is no longer the video signal on the other two monitors either. F • Branchement simultané de tous les moniteurs aussi bien à l’appel qu’au autoallumage. • Autoallumage en appuyant sur le bouton 2 du moniteur. • Attention: lorsqu’on retire le moniteur Principal alimenté par le montant, le signal vidéo s’efface également sur les deux autres moniteurs. NL • Alle monitoren gaan tegelijk aan zowel nadat er gebeld is als bij beeldoproep. • Beeldoproep na drukken op knop 2 van de monitor. • Let op: als de door de stamleiding gevoede hoofdmonitor verwijderd wordt, is er ook geen videosignaal meer op de andere twee monitoren. A NEDERLANDS I FRANÇAIS GB Connection in cascade of monitors with the same user code supplied separately. ENGLISH ITALIANO SB2/A3 I Collegamento in cascata di monitor con lo stesso codice utente alimentati separatamente. MONITOR PRINCIPALE MAIN MONITOR MONITEUR PRINCIPAL HOOFDMONITOR MONITOR PRINCIPALE MAIN MONITOR MONITEUR PRINCIPAL HOOFDMONITOR MONITOR PRINCIPALE MAIN MONITOR MONITEUR PRINCIPAL HOOFDMONITOR 101 MT SB2 01 GROUP S.P.A. GB Connection of users with the same user code in mixed systems. Telephones in cascade. F Connexion d’usagers ayant le même code usager dans des installations mixtes. Combinés parlophoniques en cascade. NL Aansluiting van gebruikers met dezelfde gebruikerscode in gemengde installaties. Cascade geschakelde deurtelefoons. ENGLISH ITALIANO SB2/A4 I Collegamento di utenti con lo stesso codice utente in impianti misti. Citofoni in cascata. NEDERLANDS FRANÇAIS MONITOR PRINCIPALE MAIN MONITOR MONITEUR PRINCIPAL HOOFDMONITOR A SB2/A5 I Collegamento di utenti con lo stesso codice utente in impianti misti. Citofoni in derivazione. GB Connection of users with the same user code in mixed systems. Branched telephones. F Connexion d’usagers ayant le même code usager dans des installations mixtes. Combinés parlophoniques en dérivation. NL Aansluiting van gebruikers met dezelfde gebruikerscode in gemengde installaties. Afgetakte deurtelefoons. MONITOR PRINCIPALE MAIN MONITOR MONITEUR PRINCIPAL HOOFDMONITOR MT SB2 01 102 MT SB2 01 ITALIANO SB2/B I Collegamento di MAX 4 diramazioni di montante per ogni Miscelatore-alimentatore Art. 4896. GB Connection of a MAX of 4 riser branches for each Mixer-power supply Art. 4896. F Connexion d’au MAX 4 dérivations du montant pour chaque mélangeur-alimentation Art. 4896. A NEDERLANDS FRANÇAIS ENGLISH NL Aansluiting van MAX. 4 stamleidingen van de voedingsmixer art. 4896. 103 MT SB2 01 GROUP S.P.A. ITALIANO SB2/C I Collegamento in cascata di Art. 4834/2. GB Connection in cascade of Art. 4834/2. F Connexion en cascade de l’Art. 4834/2. NL Cascadeschakeling van art. 4834/2. GB In caso sia necessario ottenere più delle quattro diramazioni fornite da un Art. 4834/2 (vedi SB2V/EN/112L e SB2V/EN/112 pag. 96-97) è possibile collegare in cascata due Art. 4834/2 a patto di inserire tra essi un amplificatore di segnale video Art. 4833/A (vedi schema SB2/C); su ogni uscita del primo Art. 4834/2 si può inserire al massimo un altro Art. 4834/2 in cascata in modo da arrivare ad un MAX di 16 diramazioni di montante. Riferirsi alla tabella di pag 16 colonna E per le distanze ammesse. F En cas de nécessité d’avoir un nombre de dérivations supérieur aux quatre dérivations fournies par un Art. 4834/2 (voir SB2V/EN/112L et SB2V/EN/112 pages 96-97), on pourra connecter en cascade deux Art. 4834/2 à condition d’insérer entre eux un amplificateur de signal vidéo Art. 4833/A (voir schéma SB2/C); sur chaque sortie du premier Art. 4834/2 on pourra brancher au maximum un autre Art. 4834/2 en cascade de manière à arriver à un MAX de 16 dérivations du montant. Voir le tableau de l a page 60 colonne E pour les distances admises. Should it be necessary to obtain more than the four branches provided by one Art. 4834/2 (see SB2V/EN/112L and SB2V/EN/112 on pages 96-97), it is possible to connect two Arts. 4834/2 in cascade as long as a video signal amplifier Art. 4833/A (see diagram SB2/C) is inserted between them. On each output of the first Art. 4834/2, a maximum of one other Art. 4834/2 can be inserted in cascade so as to reach a MAX of 16 riser branches. Refer to the table on page 38 column E for the permitted distances. NL Als er meer dan 4 aftakkingen nodig zijn, (zie SB2V/EN/112L en SB2V/EN/112 pag. 96-97) kunnen er twee art. 4834/2 cascade geschakeld worden mits er een videoversterker art. 4833/A tussen geplaatst wordt (zie schema SB2/C); op iedere output van de eerste buslijnverdeler art. 4834/2 kan maximaal nog één art. 4834/2 cascade geschakeld worden zodat er MAX. 16 aftakkingen gerealiseerd kunnen worden. Voor de afstanden verwijzen wij naar de tabel op pag 83 kolom E. A NEDERLANDS FRANÇAIS ENGLISH I TAGLIARE SOLO LA RESISTENZA DELL’USCITA UTILIZZATA. ONLY CUT THE RESISTANCE OF THE OUTPUT USED. COUPER SEULEMENT LA RESISTANCE DE LA SORTIE UTILISEE. VERWIJDER ALLEEN DE WEERSTAND ALS DE UITGANG GEBRUIKT WORDT. MT SB2 01 104 MT SB2 01 GB The total sum of the number of internal units with the same user code and of the number of call repetition devices connected to the abovementioned internal units cannot exceed the number of 4. Connect only one call repetition device for each internal unit. The Max. distance of the connection between internal unit and call repetition device is 20 m. Use shielded cable for the connection and do not make the cables pass near heavy inductive loads or power supply cables (220V / 380V). Set Art. 1122/A in the diagram of SB2/D for operation at 12V. Only connect devices operating in low voltage on the C-NO contacts of Art. 1122/A. In the case of connection of inductive loads, connection of a capacity of 470nF in parallel with the C-NO contacts of Art. 1122/A is recommended. F La somme du nombre de postes intérieurs ayant le même code usager et du nombre de dispositifs de répétition d’appel branchés à ces postes intérieurs ne peut pas être supérieur à 4. Brancher un seul dispositif de répétition d’appel pour chaque poste intérieur. La distance MAX de la connexion entre le poste intérieur et le dispositif de répétition de l’appel est de 20 m. Pour la connexion, utiliser un câble blindé et ne pas faire passer les câbles à proximité de charges inductives lourdes ou de câbles d’alimentation (220V / 380V). Programmer l’Art. 1122/A présent dans le schéma SB2/D pour le fonctionnement à 12V. Brancher aux contacts C-NO de l’Art. 1122/A seulement les dispositifs fonctionnant à basse tension. En cas de connexion de charges inductives, la connexion d’une capacité de 470nF en parallèle aux contacts C-NO de l’Art. 1122/A est conseillée. NL De totale som van het aantal binnentoestellen met dezelfde gebruikerscode en het aantal extra bellen dat met deze binnentoestellen verbonden is mag niet groter zijn dan 4 (dus maximaal 3 toestellen en 1 extra bel). Sluit maximaal één extra bel aan op ieder binnentoestel. De MAX. afstand tussen de binnenapparatuur en de extra bel is 20 m; gebruik afgeschermde kabels voor de aansluiting en laat ze niet in de buurt van zware inductieve lading of voedingskabels (220V / 380V) lopen. Stel het relais art. 1122/A in het schema SB2/D in voor de werking op 12V. Verbind met de C-NO contacten van het art. 1122/A alleen toepassingen die met lage spanning werken. Als er inductieve ladingen verbonden worden, wordt er aangeraden een capaciteit van 470nF parallel te verbinden aan de C-NO contacten van het relais art. 1122/A. 105 MT SB2 01 ENGLISH La somma totale del numero di posti interni con stesso codice utente e del numero di dispositivi di ripetizione chiamata collegati ai suddetti posti interni non può superare il numero di 4. Connettere un solo dispositivo di ripetizione chiamata per ogni posto interno. La distanza MAX del collegamento tra posto interno e dispositivo di ripetizione chiamata è di 20 m; utilizzare cavo schermato per il collegamento e non far passare i cavi in prossimità di carichi induttivi pesanti o cavi di alimentazione (220V / 380V). Impostare l’Art. 1122/A presente nello schema SB2/D per funzionamento a 12V. Connettere sui contatti CNO dell’Art. 1122/A solo dispositivi funzionanti in bassa tensione. In caso di connessione di carichi induttivi si consiglia la connessione di una capacità di 470nF in parallelo ai contatti C-NO dell’Art. 1122/A. FRANÇAIS I NEDERLANDS F Connexion de dispositifs de répétition d’appel sur la bride Art. 4714W/2 et sur le combiné parlophonique Art. 2428W. NL Aansluiting van extra bellen op grondplaat art. 4714W/2 en deurtelefoon art. 2428W. A GB Connection of call repetition devices on bracket Art. 4714W/2 and telephone Art. 2428W. ITALIANO SB2/D I Connessione di dispositivi di ripetizione chiamata su staffa Art. 4714W/2 e citofono Art. 2428W. GROUP S.P.A. GB Connection in cascade of several internal units (up to 25 per branch from Art. 4896). F Connexion en cascade de plusieurs postes intérieurs (jusqu’à 25 par dérivation de l’Art. 4896). NL Cascadeschakeling van meerdere binnenstations (tot en met 25 per stamleiding van de voedingsmixer art. 4896). I Nel caso di connessione in cascata il numero MAX di posti interni (monitor o citofoni) collegabili per ogni diramazione di montante del Miscelatore-alimentatore Art. 4896 è di 25. Ogni citofono Art. 2428W deve essere preceduto da un Art. 1214/2. Per le distanze ammesse tra posto interno più lontano e Miscelatorealimentatore Art. 4896 in funzione dei cavi fare riferimento alla tabella di pag. 16 colonna A. GB In the case of connection in cascade, the MAX number of internal units (monitors or telephones) connectable for each riser branch of the Mixer-power supply Art. 4896 is 25. Each telephone Art. 2428W must be preceded by an Art. 1214/2. For the distances permitted between the internal unit furthest away and the Mixer-power supply Art. 4896 according to the cables, please refer to the table on page 38 column A. A NEDERLANDS FRANÇAIS ENGLISH ITALIANO SB2/G I Connessione in cascata di più posti interni (sino a 25 per diramazione dall’Art. 4896). MT SB2 01 106 F En cas de connexion en cascade, le nombre MAXIMUM de postes intérieurs (moniteurs ou combinés parlophoniques) pouvant être branchés pour chaque dérivation du montant du mélangeur-alimentateur Art. 4896 est de 25. Chaque combiné parlophonique Art. 2428W doit être précédé d’un Art. 1214/2. Pour les distances admises entre le poste intérieur le plus éloigné et le mélangeur-alimentation Art. 4896 en fonction des câbles, se référer au tableau de la page 60 colonne A. NL Bij een cascadeschakeling kunnen MAX. 25 binnentoestellen (monitoren of deurtelefoons) op iedere stamleiding van de voedingmixer art. 4896 aangesloten worden. Iedere deurtelefoon art. 2428W moet afgetakt worden met een aftakblokje art. 1214/2. Voor de toegestane afstanden met de toegepaste kabel tussen het verste binnentoestel en de voedingsmixer art. 4896, wordt er verwezen naar de tabel op pag. 83 kolom A. MT SB2 01 ITALIANO SB2/I I Installazione elettroserratura di sicurezza con comando in mancanza si tensione temporizzato tramite Art.3340. GB Installation of fail secure door release, timed by means of Art.3340. F Installation pour commande de gâche a rupture ou ventouse, temporisée par l’Art. 3340. NEDERLANDS FRANÇAIS ENGLISH NL Installatie met (veiligheids)deuropening bij stroomuitval, aangestuurd door art. 3340. SB2/J A I Installazione elettroserratura di sicurezza con comando in mancanza si tensione temporizzato tramite Art.1184. GB Installation of fail secure door release timed by means of Art.1184. F Installation pour commande de gâche a rapture ou ventouse, temporisée par l’Art. 1184. NL Installatie met (veiligheids)deuropening bij stroomuitval, aangestuurd door art. 1184. 107 MT SB2 01 VARIANTE A VARIANT A VARIANTE A VARIANT A I GB Impiego per usi vari del pulsante 2 del citofono Art. 2408W/A o 2410W (normalmente dedicato alla chiamata a centralino). Application for various uses of push-button 2 of telephone Art. 2408W/A or 2410W (normally dedicated to the switchboard call). F Emploi pour des usages divers du bouton 2 du combiné parlophonique Art. 2408W/A ou 2410W (normalement destiné à l’appel du standard). NL Drukknop 2 kan potentieel vrij worden gemaakt. art. 2408W/A of 2410W (normaal bestemd voor het bellen naar de portierscentrale). 2 MAX 24V 100mA A NEDERLANDS FRANÇAIS ENGLISH ITALIANO GROUP S.P.A. VARIANTE B VARIANT B VARIANTE B VARIANT B I GB Utilizzo della chiamata da piano sul citofono Art. 2408W/A o 2410W. I citofoni con il medesimo codice utente suonano contemporaneamente su chiamata da piano. Use of the local floor call on telephone Art. 2408W/A or 2410W. The telephones with the same user code ring at the same time on a local floor call. F Utilisation de l’appel du palier sur le combiné parlophonique Art. 2408W/A ou 2410W. Les combinés parlophoniques ayant le même code usager retentissent en même temps à l’appel venant du palier. NL Gebruik van de etagebel op de deurtelefoon art. 2408W/A of 2410W. De deurtelefoons met dezelfde gebruikerscode bellen tegelijkertijd bij een verdiepingsoproep. MT SB2 01 108 MT SB2 01 F Utilisation pour usages divers du bouton 2 du combiné parlophonique Art. 2428W (normalement destiné à l’appel du standard). NL Drukknop 2 kan potentieel vrij worden gemaakt. art. 2428W (normaal bestemd voor het bellen naar de portierscentrale). ENGLISH Application for various uses of push-button 2 of telephone Art. 2428W (normally dedicated to the switchboard call). CV2 2 CV1 CV3 FRANÇAIS GB CV2 Utilizzo per usi vari del pulsante 2 del citofono Art. 2428W (normalmente dedicato alla chiamata centralino). 1 2 3 4 5 6 7 8 I ITALIANO VARIANTE C VARIANT C VARIANTE C VARIANT C S+ CV3 SC1 MAX 24V - 100mA P1 NEDERLANDS CFP CFP L L I GB F NL Utilizzo della chiamata da piano sul citofono Art. 2428W. I citofoni con il medesimo codice utente suonano contemporaneamente su chiamata da piano. Use of the local floor call on telephone Art. 2428W. The telephones with the same user code ring at the same time on a local floor call. Utilisation de l’appel du palier sur le combiné parlophonique Art. 2428W. Les combinés parlophoniques ayant le même code usager retentissent en même temps à l’appel venant du palier. Gebruik van de etagebel op de deurtelefoon art. 2428W. De deurtelefoons met dezelfde gebruikerscode bellen tegelijkertijd bij een verdiepingsoproep. A VARIANTE D VARIANT D VARIANTE D VARIANT D S+ SC1 P1 CFP CFP L L 109 MT SB2 01 ITALIANO GROUP S.P.A. VARIANTE E VARIANT E VARIANTE E VARIANT E I Utilizzo per usi vari del pulsante 1 del monotor (normalmente dedicato alla chiamata a centralino) sulla staffa Art. 4714W/2. F NL Application for various uses of push-button 1 of the monitor (normally dedicated to the switchboard call) on bracket Art. 4714W/2. Utilisation pour usages divers du bouton 1 du moniteur (normalement destiné à l’appel au standard) sur la bride Art. 4714W/2. 1 C1 S+ CV4 SCV3 CV4 CV6 CV3 VARIANTE F VARIANT F VARIANTE F VARIANT F Impostazione staffa Art. 4714W/2 come Secondaria con possibilità di eseguire Richiesta Video su chiamata premendo pulsante 2 del monitor. Impostare staffa come secondario agendo sul JP1 della staffa quando si hanno più monitor con lo stesso codice utente alimentati da montante. Setting bracket Art. 4714W/2 as Secondary with the possibility of carrying out Video request on a call by pressing push-button 2 of the monitor. Set bracket as secondary working on JP1 of the bracket when there are several monitors with the same user code supplied by a riser. F Programmation bride Art. 4714W/2 comme Secondaire avec possibilité d’effectuer la Demande Vidéo sur appel en appuyant sur le bouton 2 du moniteur. Programmer la bride comme secondaire en intervenant sur le JP1 de la bride en présence de plusieurs moniteurs ayant le même code usager alimentés à partir du montant. NL Instellen van de grondplaat art. 4714W/2 als Secundair, met de mogelijkheid het beeld op te roepen nadat er gebeld is d.m.v. knop 2 . Stel de grondplaat in als secundair d.m.v. JP1 van de grondplaat als er meerdere monitoren met dezelfde gebruikerscode aanwezig zijn, die geen eigen voeding hebben. 2 4 5 6 GB 7 8 I JP1 A P1 Drukknop 1 kan potentiaal vrij worden gemaakt (normaal bestemd voor het bellen naar de portierscentrale) op de grondplaat art. 4714W/2. NEDERLANDS FRANÇAIS ENGLISH CFP GB MT SB2 01 110 MT SB2 01 F NL + 20 Use of the local floor call on brackets Art. 4714W/2. The monitors with the same user code ring at the same time on a floor door call. L Utilisation de l’appel du palier sur les brides Art. 4714W/2. Les moniteurs ayant le même code usager retentissent en même temps à l’appel venant du palier. CFP 0 ENGLISH GB Utilizzo della chiamata da piano sulle staffe Art. 4714W/2. I monitor con il medesimo codice utente suonano contemporaneamente su chiamata da piano. L CFP Gebruik van de etagebel op de grondplaten art. 4714W/2. De monitoren met dezelfde gebruikerscode bellen tegelijkertijd wanneer er wordt aangebeld. FRANÇAIS I ITALIANO VARIANTE G VARIANT G VARIANTE G VARIANT G P1 C1 NEDERLANDS S+ Activation en option Autoallumage (seulement pour les installations avec 1 ou 2 entrées) sur le moniteur avec brides Art. 4714W/2 programmées comme Principales (voir JP1 de figure). Appuyer sur le bouton 2 du moniteur pendant au moins 2 sec. jusqu’à ce que l’on entende le bip de confirmation. Pour débrancher appuyer à nouveau sur le bouton 2 pendant au moins 2 sec. jusqu’à ce qu’on entende le bip de confirmation. NL Optionele activering beeldoproep (alleen voor installaties met 1 of 2 ingangen) op monitoren met grondplaten art. 4714W/2 die ingesteld zijn als hoofdmonitor (zie JP1 op de afbeelding). Houd knop 2 van de monitor minstens 2 seconden ingedrukt totdat u een geluid ter bevestiging hoort. Om deze functie te deactiveren moet u knop 2 opnieuw gedurende minstens 2 seconden ingedrukt houden totdat u het geluid ter bevestiging hoort. 7 8 F 2 6 Activation of optional Self-ignition (only for systems with 1 or 2 entrances) on monitor with brackets Art. 4714W/2 set as Main (see JP1 of the figure). Keep push-button 2 of the monitor pressed for at least 2 sec. until the confirmation tone is heard. To de-activate it, press push-button 2 again for at least 2 sec. until the confirmation tone is heard. 5 GB 4 Attivazione opzionale Autoaccensione (solo per impianti con 1 o 2 ingressi) su monitor con staffe Art. 4714W/2 impostate come Principali (vedi JP1 di figura). Tener premuto il pulsante 2 del monitor per almeno 2 sec. finchè non si ode tono di conferma. Per disattivare premere nuovamente il pulsante 2 per almeno 2 sec. finchè non si ode tono di conferma. JP1 I A VARIANTE H VARIANT H VARIANTE H VARIANT H 111 MT SB2 01 VARIANTE I VARIANT I VARIANTE I VARIANT I I Attivazione della funzione Privacy su monitor della serie Videocom con scheda opzionale Art. 4703. Premere il pulsante 4 per almeno 2 sec. finchè non si accende il LED. Quando inserita, la Privacy esclude la suoneria sul monitor su cui è stata attivata; il monitor si accende e si ha comunque la possibilità di andare in comunicazione con il posto esterno. Per disattivare premere nuovamente il pulsante 4 finchè non si spegne il LED. F Activation de la fonction Privacy sur le moniteur de la série Videocom avec carte en option Art. 4703. Appuyer sur le bouton 4 pendant au moins 2 sec. jusqu’à ce que la led s’éclaire. Lorsque la fonction Privacy est branchée, elle coupe la sonnerie du moniteur sur lequel elle a été activée ; le moniteur se branche et l’on a de toute façon toujours la possibilité de communiquer avec la plaque de rue. Pour débrancher, appuyer à nouveau sur le bouton 4 jusqu’à ce que la led s’éteigne. GB Activation of the Privacy function on monitors of the Videocom series with optional card Art. 4703. Press push-button 4 for at least 2 sec. until the LED lights up. When inserted, the Privacy function excludes the call tone to the monitor on which it has been activated. The monitor ignites and in any case there is the possibility of communication with the external unit. To de-activate it, press push-button 4 again until the LED turns off. NL Activering van de Privacy functie op monitoren van de serie Videocom met optionele kaart art. 4703. Druk knop 4 gedurende minstens 2 seconden in totdat de LED oplicht. Wanneer de Privacy functie is ingeschakeld, wordt de beltoon op de monitor waar deze functie geactiveerd is gedeactiveerd; het beeld verschijnt en u kunt wel met de bezoeker praten. Om deze functie weer te deactiveren, knop 4 opnieuw indrukken totdat de LED dooft. A NEDERLANDS FRANÇAIS ENGLISH ITALIANO GROUP S.P.A. 4 MT SB2 01 112 MT/SB2/01 - 2a edizione 02/2004 - cod. 22591224 Comelit Group S.p.A. - Via Don Arrigoni 5 - 24020 Rovetta S. Lorenzo BG Italy - tel. (+39) 0346 750 011 - fax (+39) 0346 71436 www.comelit.it [email protected] [email protected] [email protected] 15, Rue Jean Zay - 69800 Saint Priest Tel 04 72 28 06 56 - Fax 04 72 28 83 29 http://www.comelit.fr E-mail: [email protected] F Polderweg Oost 26 - 2973 An Molenaarsgraaf Tel 0184 64 91 58 - Fax 0184 64 01 58 http://www.comelit.nl E-mail: [email protected] NL Chaussée de Ninove, 900 - 1703 Schepdaal (Dilbeek) Ninoofsesteenweg, 900 - 1703 Schepdaal (Dilbeek) Tel 02 411 50 99 - Fax 02 411 50 97 http://www.comelit.be E-mail: [email protected] B 1 Brownfields - Welwyn Garden City HERTS - AL7 1AN Tel 01707 377203 - Fax 01707 377204 http://www.comelitgroup.co.uk E-mail: [email protected] UK