temperatura di fitness
Transcript
temperatura di fitness
ZI Haneboesch L-4562 Differdange LUXEMBOURG Telefono : +352 58 22 82 1 Fax : +352 58 49 35 Scheda Tecnica E-mail : [email protected] Sito web : www.airtech.lu TOOLFUSION® 3 Resina per infusione ad alta temperatura con bassa temperatura di polimerizzazione iniziale DESCRIZIONE Toolfusion® 3 è una resina epossidica bicomponente a bassa viscosità utilizzata per la realizzazione, tramite infusione, di stampi in composito preimpregnati. Toolfusion® 3 ha una bassa temperatura iniziale di polimerizzazione (49 ºC) e può essere sottoposta a post-polimerizzazione per raggiungere un’elevata temperatura di transizione vetrosa (218 ºC). È possibile raggiungere un contenuto di vuoti inferiore all’1%. Toolfusion® 3 è adatto a vari processi RTM (Resin Transfer Molding) e VARTM (Vacuum Assisted Resin Transfer Molding) tra cui sacchi singoli e doppi per produrre laminati di qualità pari a quella dell’autoclave. BENEFICI > Il processo di infusione della resina fornisce laminati di altissima qualità con bassi costi di produzione e nessun costo di refrigerazione e di funzionamento dell’autoclave. > La bassa temperatura iniziale di indurimento porta a un ridotto effetto di dilatazione termica durante la polimerizzazione consentendo di utilizzare materiali a basso costo per i modelli master. > L’impiego delle nanotecnologie offre una straordinaria solidità e un’elevata temperatura di transizione vetrosa (218 ºC) che consentono una lunga durata degli utensili e la riduzione dei costi del ciclo di vita. > La bassa viscosità consente l’infusione di laminati più spessi e complessi con minori linee di alimentazione della resina. > Rispetto agli stampi metallici, gli attrezzi compositi Toolfusion® 3 sono più leggeri e semplici da maneggiare e riducono i costi di produzione grazie alla minore inerzia termica. > I laminati per utensili compositi Toolfusion® 3 hanno resistenza sufficiente per l’utilizzo nel processo sotto vuoto sia in forno che in autoclave. Ultima revisione : 2016-07-18 Capitolo : Prodotti per infusione di resina As the conditions or methods of use, including storage, are beyond our control, Airtech Europe does not assume any responsibility for the performance of this material for any particular use. The material is sold "as is". Airtech Europe disclaims, and buyer waives, any and all implied warranties, including without limitation the implied warranties of merchantability and of fitness for particular use. The information contained herein represents typical properties and should not be used for specification purposes. This translation is provided for your convenience only. The official language is English and the official law is Luxembourg. ZI Haneboesch L-4562 Differdange LUXEMBOURG Telefono : +352 58 22 82 1 Fax : +352 58 49 35 Scheda Tecnica E-mail : [email protected] Sito web : www.airtech.lu TOOLFUSION® 3 Resina per infusione ad alta temperatura con bassa temperatura di polimerizzazione iniziale DATI TECNICI Metodologia del test Tipo di materiale Colore Rapporto di miscelazione in base al peso Tempo d'utilizzo Viscosità (initial a 22 °C) Densità (mescolato) Temperatura di transizione vetrosa Durezza Retraibilità Epossidico Nero : Chiaro (A : B) 100 : 85 (A : B) 300 minuti (100 g a 22 °C) 450 cps 1,13 g/cm3 218 °C 89 Barcol 0,9 % Vita del prodotto 12 mesi ASTM D2583 DIMENSIONI Imballaggio Parte A Imballaggio Parte B Peso Parte A Peso Parte B 5 galloni 5 galloni 45 Lbs (20,4 Kg) 40 Lbs (18,1 Kg) CICLO DI POLIMERIZZAZIONE Ultima revisione : 2016-07-18 Capitolo : Prodotti per infusione di resina As the conditions or methods of use, including storage, are beyond our control, Airtech Europe does not assume any responsibility for the performance of this material for any particular use. The material is sold "as is". Airtech Europe disclaims, and buyer waives, any and all implied warranties, including without limitation the implied warranties of merchantability and of fitness for particular use. The information contained herein represents typical properties and should not be used for specification purposes. This translation is provided for your convenience only. The official language is English and the official law is Luxembourg. ZI Haneboesch L-4562 Differdange LUXEMBOURG Telefono : +352 58 22 82 1 Fax : +352 58 49 35 Scheda Tecnica E-mail : [email protected] Sito web : www.airtech.lu TOOLFUSION® 3 Resina per infusione ad alta temperatura con bassa temperatura di polimerizzazione iniziale Polimerizzazione iniziale: > Polimerizzare il laminato su un modello master sotto vuoto completo. > Portare la temperatura a 49 ºC e mantenerla per 12 ore. > Rimuovere i materiali per sacchi a vuoto e attaccare la struttura di supporto agganciata, se necessario. > Rimuovere con cautela il laminato e proseguire con il processo di post-polimerizzazione. Programma di post-polimerizzazione: > Portare la temperatura a 65 ºC e mantenerla per 60 minuti. > Portare la temperatura a 93 ºC e mantenerla per 60 minuti. > Portare la temperatura a 121 ºC e mantenerla per 60 minuti. > Portare la temperatura a 149 ºC e mantenerla per 60 minuti. > Portare la temperatura a 177 ºC e mantenerla per 60 minuti. > Portare la temperatura a 204 ºC e mantenerla per 120 minuti. Nota: la Parte A e la Parte B sono vendute separatamente. Ultima revisione : 2016-07-18 Capitolo : Prodotti per infusione di resina As the conditions or methods of use, including storage, are beyond our control, Airtech Europe does not assume any responsibility for the performance of this material for any particular use. The material is sold "as is". Airtech Europe disclaims, and buyer waives, any and all implied warranties, including without limitation the implied warranties of merchantability and of fitness for particular use. The information contained herein represents typical properties and should not be used for specification purposes. This translation is provided for your convenience only. The official language is English and the official law is Luxembourg.