UFF-003 - Meerwasser Hardware
Transcript
UFF-003 - Meerwasser Hardware
ULTRA REEF www.ultrareef.it MANUALE ISTRUZIONI INSTRUCTION MANUAL UFF-003 IT · EN V.2015.09 1 ULTRA REEF www.ultrareef.it 2 ULTRA REEF www.ultrareef.it MANUALE ISTRUZIONI 5. Inserite il filtro estraibile sulla base avviate il carico dell’acqua con il flusso desiderato. Attenzione: Per maggiori informazioni e approfondimenti su questo prodotto consultate i manuali disponibili sul sito www.ultrareef.it prima dell’utilizzo. Regolate la portata d’acqua e il volume di riempimento secondo quanto riportato dal produttore del media. Suggeriamo di installare a valle della pompa di carico una saracinesca/rubinetto per poter regolare il flusso d’acqua. Nel momento in cui il sistema viene installato diventa totale responsabilità dell’utilizzatore valutarne la tenuta, l’efficacia e l’idoneità all’uso. Qualunque perdita d’acqua e danno conseguente resta responsabilità dell’utilizzatore. Attenzione: L’utilizzo del prodotto implica l’accettazione di tutte le condizioni riportate nel manuale “Sicurezza e garanzia” e ne sottintende la precedente lettura e totale comprensione. Risciacquate attentamente con acqua e aceto (diluito al 10%) ogni componente che andrà in contatto con l’acqua. Prodotti a base di alcool o solventi possono danneggiare l’acrilico. 1. INTRODUZIONE Attenzione: Collegate la tubazione di carico (non fornita) al portagomma di carico. Il filtro può essere alimentato con pompe regolabili per acquari fino a 1000 l/h. Prima di procedere con l’installazione preparate il media di carico. Seguite le istruzioni di preparazione riportate dal fornitore del media. Attenzione: in questo manuale si utilizza il termine “media” per indicare il materiale di riempimento del reattore. Seguite le istruzioni riportate sulle immagini per aprire e chiudere il filtro. Orientate e fissate la tubazione di carico secondo le vostre esigenze. 2. USO Per riempire il filtro: 1. Rimuovete il filtro estraibile. 2. Rimuovete la vite, la griglia e la spugna. 3. Riempite il reattore con il media e richiudete. 4. Posizionate la base nella sump. 3 ULTRA REEF www.ultrareef.it INSTRUCTION MANUAL Adjust the water flow and the filling volume as reported by the manufacturer of the media. Warning: For more information and details on this product, refer to manuals available on the site www.ultrareef.it before start up product. We recommend you to install a gate valve after the load pump to adjust water flow. After system installation, it has becomes full responsibility of the user to evaluate the tightness, the effectiveness and suitability of product. Any loss of water and consequent damage remains responsibility of the user. Warning: The use of the product implies acceptance of all conditions contained in the manual "Safety and Warranty" and it implies previous reading and total understanding. Clean thoroughly with water and vinegar (diluted to 10%) each component that will go into contact with water. Products that contains alcohol or solvents can damage the acrylic. 1. OVERVIEW Warning: Connect the load line (not provided) to the loading hose. The filter may be supplied with pumps for aquariums up to 1000 l/h. Before perform installation, prepare the medium. Follow the preparation instructions provided by the supplier of the media. Warning: This manual uses term "media" to indicate the filling material of the reactor. Follow the instructions on the images to open and close the filter. Rotate and secure the inlet load pipe according to your needs. 2. USE To fill the filter: 1. Remove the removable filter. 2. Remove the screw, the grille and the sponge. 3. Fill the reactor with the media and close it. 4. Place the base in sump tank. 5. Place the removable filter based start water loading with the desired flow. 4