inv01/innovo - Bathstore
Transcript
inv01/innovo - Bathstore
INV01 96 (3 25/32”) _ REV10 DESIGN NATALINO MALASORTI Ø17 155 (6 7/64”) (Ø43/64”) Ø30 INV01/INNOVO 4 (5/32”) 73 (2 7/8”) (max. 2 11/64”) MAX. 55 mm (Ø1 3/16”) AISI 316/L STAINLESS STEEL Miscelatore monoforo con bocca erogazione girevole per getto a zampillo H. 155 mm, apertura dall’acqua fredda Ø45 (Ø1 49/64”) Deck mounted mixer with swivelling spout for gush flow H. 155 mm, opening in cold water Ø35 (Ø1 3/8”) Risparmio idrico (5 - 10 lt/min) Water saving (5 - 10 lt/min / 1,3 - 2,6 gal/min) MANUTENZIONE / MAINTENANCE L. 600 mm (1’ - 11 5/8”) NON UTILIZZARE DO NOT USE HCl acido clorico e muriatico cloric and muriatic acid HFl acido fluoridrico hydrofluoric acid NaClO UTILIZZARE TO USE PH 5.5 ipoclorito di sodio chlorine bleach sapone a PH neutro neutral PH soap 149 (5 55/64”) 3/8” GAS Questo disegno è proprietà di CEADESIGN srl pertanto non potrà essere utilizzato e/o comunicato a terzi, anche in forma parziale, senza preventiva autorizzazione. CEADESIGN srl si riserva il diritto di apportare modifiche al disegno al fine di migliorare il prodotto. CEADESIGN srl has the property rights on this drawing, therefore it cannot be used and/or transferred to third party, even in partial form, without any prior authorization. Furthermore CEADESIGN srl reserves the right to apply any change to the drawing in order to upgrade the product. CEADESIGN Srl Via A. De Gasperi, 48 36060 Pianezze / VI - Italy T +39 0424 572309 [email protected] www.ceadesign.it INV01 _ REV10 AVVERTENZE TECNICHE Risciacquare bene le tubazioni prima del montaggio ed evitare sbalzi di pressione fra i raccordi d’acqua fredda e d’acqua calda. In caso di pressioni statiche superiori a 5 bar si raccomanda l’installazione di un riduttore di pressione per evitare danni alla cartuccia. TECHNICAL WARNINGS (max. 2 11/64”) MAX. 55 mm The pipes have to be rinsed thoroughly before installation. Avoid pressure differences between hot and cold water supply. Use of a pressure reducer when static pressure is higher than 5 bar to avoid dammage of the cartridge. A TECHNISCHE WARNUNG A Ø35 (Ø1 3/8”) Spülen Sie die Leitungen vor dem Einbau und verhindern Sie Wasserdruckwechsel zwischen kalt und warm Wasserverbindungen. Wenn Wasserddruck größer als 5 bar ist, bitte reduzieren Sie den Systemdruck, um Beschädigung der Kartusche zu verhindern. ADVERTENCIA TÉCNICA B 1 2 PULIZIA / CLEANING / SAUBEKEIT / LIMPIEZA / NETTOYAGE B Los tubos tienen que ser enjuagados a fondo antes de la instalación. Evitar grandes diferencias de presión entre las conexiones de agua caliente y fría. En caso de presión estática mayor de 5 bar, se recomienda el uso de un adaptador de presión para evitar daños en el cartucho. ADVERTISSEMENTS TECHNIQUES Rincer les tuyaux avant l’installation. Eviter des grandes différences de pression entre l’eau froide et chaude. En cas de pressions statique de plus de 5 bar, nous vous recommandons d’installer un réducteur de pression pour éviter des dommages à la cartouche. TABELLA DI PORTATA / FLOW RATE TABLE P2 P1 P2 BAR l/min gal/min l/min gal/min 1 2 3* 4 5 4,6 6,5 7,9 9,1 10,0 1,2 1,7 2,1 2,4 2,6 1,8 2,5 3,1 3,6 3,8 0,5 0,7 0,8 0,9 1,0 BAR l/min gal/min 1 2 3* 4 5 2,1 2,9 3,6 4,1 4,4 0,5 0,8 0,9 1,1 1,2 P3 Pressione consigliata Recommended pressure P3 P1 max. 70 °C max. 158 °F CEADESIGN Srl Via A. De Gasperi, 48 36060 Pianezze / VI - Italy T +39 0424 572309 [email protected] www.ceadesign.it INV01 RICM029 S/L* _ REV10 COMPONENTI / PARTI DI RICAMBIO RICA011 RICC017 RICF017 RICH008 RICM029 RICR025 RICS013 RICS015 RICS016 RICR025 S/L* Aeratore Cartuccia Flessibile Ghiera Maniglia Rosetta Sacchetto Sacchetto Sacchetto COMPONENTS / SPARE PARTS RICA011 RICC017 RICF017 RICH008 RICM029 RICR025 RICS013 RICS015 RICS016 RICH008 S/L* RICS016 Aerator Cartridge Hose Sleeve Handle Rosette Bag Bag Bag RICC017 RICS013 RICS015 LEGENDA / LEGEND ICONE / ICONS utensili inclusi nel ricambio tools included in spare parts FINITURE / FINISHINGS *S L finitura satinata / satin finish finitura lucidata / polished finish Questo disegno è proprietà di CEADESIGN srl pertanto non potrà essere utilizzato e/o comunicato a terzi, anche in forma parziale, senza preventiva autorizzazione. CEADESIGN srl si riserva il diritto di apportare modifiche al disegno al fine di migliorare il prodotto. CEADESIGN srl has the property rights on this drawing, therefore it cannot be used and/or transferred to third party, even in partial form, without any prior authorization. Furthermore CEADESIGN srl reserves the right to apply any change to the drawing in order to upgrade the product. RICA011 RICF017 CEADESIGN Srl Via A. De Gasperi, 48 36060 Pianezze / VI - Italy T +39 0424 572309 [email protected] www.ceadesign.it