RESISTO TELESCOPICO Installazione-Installation
Transcript
RESISTO TELESCOPICO Installazione-Installation
RESISTO TELESCOPIC Installazione Prima di fissare gli elementi considerare l’ingombro della barra RESISTO nella posizione verticale ed orizzontale. Per la misura orizzontale fare riferimento alla tabella sottostante. Si consiglia di effettuare l’applicazione di RESISTO nella parte inferiore dello scuro parte più a rischio di scasso. Fissaggio degli incontri, appoggiare la barra RESISTO allo scuro, con le viti 5x35 e i bulloni 5x60. Fissaggio del supporto a parete, per la praticità di RESISTO si consiglia di fissare il supporto alla parete. Appoggiare la Sbarra di RESISTO agli incontri, far corrispondere il centro del catenello con la sbarra, fissare il supporto con le viti d. 4,5x50 utilizzando i tasselli Ø 6 mm. Fissaggio del pozzetto a molla, posizionare in orizzontale la sbarra di RESISTO, segnare la posizione dove eseguire il foro per l’innesto dell’asta minore, fissare il pozzetto con silicone. Modo d’uso in Antieffrazione, sollevare dal supporto la sbarra RESISTO e accompagnarla in appoggio agli incontri, con il pomello fare un movimento orizzontale fino che l’asta minore finisce la corsa all’int. del pozzetto, poi stringere il pomello. Per aprire, fare la procedura inversa della chiusura. RESISTO Dimensioni disponibili La misura massima è 140 cm e la minima è 35 cm Misura foro luce cm Foro asta minore Asola asta maggiore Modifiche Misure inferiori a 110 Primo Prima Taglio 2 aste 110 Primo Prima Nessuna Da…..110 a 120 Secondo Seconda Taglio asta minore 120 Secondo Seconda Nessuna Da….120 a 140 Primo Seconda Taglio asta minore 140 Primo Seconda Nessuna Per misure inferiori a cm 110 l’asta maggiore, incluso il supporto, va tagliata di 2 cm della misura foro luce, mentre l’asta minore va tagliata di 17,5 cm (primo foro prima asola). CDS CENTRO DISTRIBUZIONE SICUREZZA SRL 35010 Limena (PD) Via Pierobon 129 T. +39 049 8841502 F. +39 049 8846168 www.cdslimena.it - [email protected] RESISTO TELESCOPIC Installation Before fixing elements consider the dimensions of the Bar RESISTO in vertical and horizontal position. For the horizontal dimension see the table below. The application of RESISTO is recommended in the lower side of the shutter (side most at burglary risk). Fixing of keeps, arranging keeps, put the bar on the shutter, with the screws 5x35 and bolts 5x60. Attaching the wall support, for the convenience of RESISTO it is recommended to attach the mount to the wall in the frame inside the door is opened before the opening of the shutter matter, support the busbar RESISTO keeps, to match the center of the chains with the bar, secure the stand with screws d. 4.5 x50 using the dowels Ø 6 mm. Attaching the cockpit spring, place in horizontal position the RESISTO, mark the position for the lower hole and grafting auction minor fix the well with silicone. How to use Break-in, lift the bar from the support and accompany RESISTO in support of the keeps, with the knob to make a move horizontally until the auction ends lower the ride to the inside of the cockpit, then tighten the knob. To open, do the reverse procedure of closing. RESISTO Available dimensions The maximum dimension is 140 cm and the minimum is 35 cm Hole dimension in cm Hole lower bar Upper bar slot Changes Dimensions less 110 First First Cut of both bar 110 First First Nothing From…..110 to 120 Second Second Cut of lower bar 120 Second Second Nothing From….120 to 140 First Second Cut of lower bar 140 First Second Nothing For dimensions small than 110 cm, the upper bar, including the support, must be cutted less 2 cm respect the hole wall dimension. The lower bar must be cutted less 17,5 cm (first hole first slot). CDS CENTRO DISTRIBUZIONE SICUREZZA SRL 35010 Limena (PD) Via Pierobon 129 T. +39 049 8841502 F. +39 049 8846168 www.cdslimena.it - [email protected]