VEG2000 - VEGA SRL
Transcript
VEG2000 - VEGA SRL
VEG2000 SCHEDA QUADRO / LIFT CONTROL BOARD HammerADV VEG2000 SCHEDA QUADRO Questa scheda di controllo a microprocessore gestisce tutti I tipi di ascensori sia in seriale che in parallelo. - Conforme alle norme UNI EN 81-1/2. - Impianti fino a 32 fermate universali o prenotato salita/discesa, collegamento parallelo, seriale o seriale/parallelo. - Impianti idraulici e a fune. - Impianti a fune fino a 8 velocità con regolatore VVVF tramite ENCODER. - Funzionalità duplex e duplex zoppo. - Predisposizione per funzionalità multiplex. - Scheda programmabile completamente da display LCD (16 caratteri x 2 righe) o da Computer sia in locale che in remoto con ausilio di una scheda modem. - Display estraibile, adattabile al montaggio verticale o orizzontale. - Controllo delle Sicurezze fino a 230Vac. - Alloggiamento per SD MEMORY CARD per memorizzare e aggiornare FIRMWARE e PARAMETRI. - Telecontrollo e manutenzione locale e remota con ausilio di una scheda modem, senza schede aggiuntive. - Comunicazione seriale testata fino a 120m senza necessità di cavo schermatura. - Alimentazione 13-24 Vac tramite switching integrato. - Possibilità di montare l’apposito pannello di protezione con serigrafia e logo. - Carica batterie integrato a 12V (distacco automatico della batteria in caso di spegnimento); uscita ausiliare a 12V stabilizzata, presente anche senza alimentazione. - Predisposta per l’innesto di moduli di espansione (VVVF + ENCODER). - Data e ora locale tramite gsm. LIFT CONTROL BOARD This is a control board to manage microprocessor control panels for all kind of lifts with parallel or serial communication. - Compliance with UNI EN 81-½ STANDARD. - Lift up to 32 stops for single call or collective plants, parallel, serial or compound connection. - Traction and hydraulic lifts. - Traction lifts up to 8 speeds with VVVF by ENCODER. - Duplex and asymmetrical management. - Predisposition to multiplex management. - It is totally programmable by an integrated LCD display (16 columns x 2 lines) in local or remote via computer by GPRS/ ISDN. - Removable LCD display, it can be mounted both in vertical and horizontal way on the board or outside. - Security circuit monitoring and drive contactors control up to 230Vac. - Placement for SD MEMORY CARD to store and update FIRMWARE and parameters. - For remote monitoring and inspection service it needs only one modem. - Serial connection tested up to 120mt without shielded cable. - Power supply 13-24 Vdc by integrated switching. - Opportunity of protection panel mounting for serigraph and mark. - Integrated Battery charger and controller module at 12V (in case of battery running out: automatic separation); auxiliary output at 12V regulated, present even without main power supply. - Predisposed to expansion modules insertion (VVVF+ENCODER). - date and local time by GSM. VEG2000 + VEG400 VEG2000 VEG2000 N° FERMATE (SCHEDA DI ESPANSIONE) SERIALE N° FERMATE VEG2000 VEG2000 + VEG400 VEG2000 N° STOPS (EXPANSION BOARD) N° FERMATE N° STOPS SERIAL N° STOPS UNIVERSALE 24 24 32 1 SINGLE CALL PLANT 24 24 32 PRENOTATO DISCESA 12 24 32 DOWN COLLECTIVE 12 24 32 PRENOTATO SALITA/ DISCESA 8 12 32 UP/DOWN COLLECTIVE 8 12 32 Nota 1: Gestione display 1)Binaria con 5 uscite disponibili. 2)Seriale. 3)1 polo per piano; il numero di fermate diminuisce a seconda dei piani. Note 1: Display Management 1)Binary, 5 outputs available. 2)Serial. 3)1 wire for floor ; the number of stops decreases. Nota 2: Per aumentare il numero di fermate sono disponibili ulteriori espansioni (VEG400). Note 2: To increase the number of stops are expansion boards can be used (VEG400). VEGA srl P. Iva 01578140442 Via degli Appennini 11/13 63845 Ponzano di FERMO (FM) ITALY T +39 0734 631941 F +39 0734 636098 E [email protected] www.vegalift.it