pompe a pistoni ad asse inclinato
Transcript
pompe a pistoni ad asse inclinato
108-015/915 108-016/916 108-907 CODICE FAMIGLIA POMPE A PISTONI AD ASSE INCLINATO FAMILY CODE 84-108 130 BENT AXIS PISTON PUMPS Minerale o sintetico compatibile con guarnizioni: Rev:AG Fluido idraulico Mineral or synthetic compatible with the following seals: Fluid Codice foglio:997-108-01520 FKM, FPM, HNBR Viscosità cinematica T media ambiente (°C) < -40 -40÷10 10÷35 Average ambient temp. (°C) consigliata Kinematic viscosity suggested VG (cSt = mm2/s) 16 22 Viscosità cinematica ottimale di esercizio > 35 32 46 VG= 10 cSt ÷ 100 cSt Optimale kinematic viscosity Viscosità cinematica max consentita all’avviamento VG= 750 cSt Max kinematic viscosity suggested at the start-up Indice di viscosità consigliato VI > 100 Viscosity index suggested Senso di rotazione > 200 bar: 10 µm < 200 bar: 25 µm 0,85 ÷ 2 bar assoluti/absolut Unidirezionale (Dx o Sx) Pump rotation Unidirectional (Right or Left) Grado di filtrazione Oil filtering Pres. di aspirazione Inlet pressure Verificare che la pompa sia posizionata almeno 100 mm sotto il livello minimo del serbatoio olio. Prima di avviare la pompa effettuare spurgo aria. Data: Giovedì 7 settembre 2006 Codice fascicolo:997-400-10810 Rev:AM Verify that pump is, at least, 100 mm under the minimum level of the tank. Before starting the pump bleed the air. Dimensions in mm Rotazione Rotation Tipo pompa Pump type HDS-84 HDS-108 MDS-130 Destra Sinistra Right Left 108-015-08033 108-915-08034 108-015-10833 108-915-10834 108-907-01086 108-016-01306 108-916-01307 IN OUT IN ISO 228 ISO 228 SAE 24 108-015-08042 G 1 1/4 108-915-08043 108-015-10842 G 1 1/2 108-915-10843 108-907-01095 108-016-01315 G 1 1/2 108-916-01316 Temp. di funzionamento Working OUT temperature SAE 16 G1 G1 1 7/8-12 1 5/16-12 G1 pag.19 O.M.F.B. S.p.A. Hydraulic Components We reserve the right to make any changes without notice. Edition 2002.11 No reproduction, however partial, is permitted. Via Cave, 7/9 25050 Provaglio d’Iseo (Brescia) Italy Tel.: +39.030.9830611 Fax: +39.030.9839207-208 Internet:www.omfb.it e-mail:[email protected] min max -15° -40° -15° -40° -15° -15° -40° 200° 140° 200° 140° 200° 200° 140° SCHEMA RICAMBIO POMPE A PISTONI HDS 84-108 E MDS 130 108 Codice fascicolo:997-400-10810 Rev:AM 12 8 pag.20 O.M.F.B. S.p.A. Hydraulic Components We reserve the right to make any changes without notice. Edition 2002.11 No reproduction, however partial, is permitted. Via Cave, 7/9 25050 Provaglio d’Iseo (Brescia) Italy Tel.: +39.030.9830611 Fax: +39.030.9839207-208 Internet:www.omfb.it e-mail:[email protected] Data: Giovedì 7 settembre 2006 1 17 2 3 18 4 5 19 6 7 20 21 22 23 9 24 10 11 25 26 27 28 13 29 14 30 15 31 32 16 33 Codice foglio:997-108-01520 Rev:AG HDS PISTON PUMP 84-108 AND MDS 130 SERIES SPARE PARTS O.M.F.B. S.p.A. Hydraulic Components pag.21 We reserve the right to make any changes without notice. Edition 2002.11 No reproduction, however partial, is permitted. Via Cave, 7/9 25050 Provaglio d’Iseo (Brescia) Italy Tel.: +39.030.9830611 Fax: +39.030.9839207-208 Internet:www.omfb.it e-mail:[email protected] 32 33 31 30 26 27 28 29 25 24 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 20 21 22 23 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • GAS SAE -40°C GAS • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • GAS SAE -40°C HDS 108 MDS 130 GAS SAE -40°C GAS HDS 84 GAS 19 18 13 14 15 16 17 12 5 6 7 8 9 10 11 4 1 2 3 N° N° Data: Giovedì 7 settembre 2006 Rosetta elastica Vite TCE M12x45 Corpo posteriore Guarnizione OR Corpo intermedio Rondella rame Tappo cieco Guarnizione compensazione gioco Guarnizione Corpo cilindri sede pistoni Perno sferico con guida albero Molla di carico corpo cilindri Anello guida molla Anello seeger Fasce elastiche Pistone sferico Cuscinetto Anello distanziale cuscinetti Cuscinetto Corona dentata Albero Guarnizione OR Anello seeger rinforzato Rondella Rondella Corpo anteriore Bussola Targhetta completa Chiodino fissaggio targhetta Paraolio Washer Socket head capscrew Rear cover O-ring Int. body Copper washer Blank plug Backlash gasket Gasket Piston barrel Shaft guide pin Spring Spring guide ring Retaining ring Spring rings Piston Ball bearing Bearing spacer ring Ball bearing Crown Shaft O-ring Retaining ring Spacers Spacers Front body Bushing Plate Plate nail Oil seal Socket head capscrew Washer Circlip Description 502-000-00318 501-008-00063 501-000-02729 506-021-42726 506-000-24272 501-000-01355 529-007-00217 529-007-00226 517-002-00628 511-002-00200 513 513-000-00011 506-006-03137 506-000-13137 510-002-00364 530-004-00182 510-002-00355 525-011-00111 522-005-00179 532-005-00034 532-005-00070 532-005-00105 501-023-00037 501-023-00055 501-023-00117 542-001-00162 512-005-00812 542-001-00171 501-015-00028 517-003-00092 517-003-00145 517-003-00172 506-006-00305 506-000-12412 517-002-00806 116-009-01200 115-006-00135 507-000-00274 506-006-08521 506-000-18520 517-002-00780 517-002-00799 517-002-00851 517-002-00897 501-008-00063 502-005-00573 Descrizione Codice Codice foglio:997-108-01520 P. Number Vite TCE M 12x45 Rosetta elastica Anello elastico Codice fascicolo:997-400-10810 Rev:AM Rev:AG 4 4 1 1 1 1 1 1 1 1 1 1 1 1 21 7 1 1 1 1 1 1 1 2 2 1 1 1 2 1 4 4 1 Quantity Quantità 108 SCHEMA RICAMBIO POMPE A PISTONI HDS 84-108 E MDS 130 HDS PISTON PUMP 84-108 AND MDS 130 SERIES SPARE PARTS 108-015/915 108-016/916 108-907 POMPE A PISTONI AD ASSE INCLINATO 84-108 130 BENT AXIS PISTON PUMPS CARATTERISTICHE TECNICHE DI FUNZIONAMENTO TECHNICAL FEATURES Pressure Displacement Min. speed P1 P2 P3 speed speed cm3/rev bar bar bar rpm rpm rpm HDS-84 HDS-108 84,33 107 350 370 400 1500 2000 300 MDS-130 131,62 250 kg 17,8 260 270 1500 2000 300 P1=Pressione max.continua Max. continuous pressure (100%) P2=Pressione max. intermittente Max. Intermittent pressure (20 sec.max.) P3=Pressione max. di punta Max. peak pressure (6 sec.max) COPPIA ASSORBITA FLOW DRIVE TORQUE 700 200 MDS 130 HDS 108 600 160 550 HDS 84 140 HDS 108 650 180 MDS 130 HDS 84 500 450 120 Nm 100 400 350 250 60 200 40 150 100 20 50 500 1000 1500 2000 2500 50 rpm 250 300 350 400 SCELTA DEL TUBO DI ASPIRAZIONE ∅ interno min. tubo Velocità flusso Q 110 400 bar 100 90 350 bar 80 300 bar 70 kW 200 HOW TO CHOOSE THE SUCTION PIPE SIZE POWER INPUT 250 bar 60 50 200 bar 40 150 bar 30 100 bar 20 10 100 150 200 Q (l/min) Kit guarnizioni Seal Kit GAS SAE GAS -40° 150 bar POTENZA ASSORBITA 50 100 108-903-84009 108-903-84018 Min pipe diam. Flow speed mm inch (m/s) 30 32 0,62 1” 1/4 40 32 0,83 50 38 0,74 1” 1/2 60 38 0,88 70 40 1” 9/16 0,93 80 45 0,84 1” 3/4 90 45 0,94 100 50 0,85 2” 110 50 0,93 120 60 0,71 130 60 0,77 2” 3/8 140 60 0,83 150 60 0,88 160 63 0,86 170 63 2” 1/2 0,91 180 63 0,96 Per garantire corrette condizioni di aspirazione la velocità del flusso non deve superare 1 m/sec. To ensure the proper suction pipe size the flow speed should not exceed 1mt/sec. pag.22 O.M.F.B. S.p.A. Hydraulic Components We reserve the right to make any changes without notice. Edition 2002.11 No reproduction, however partial, is permitted. Via Cave, 7/9 25050 Provaglio d’Iseo (Brescia) Italy Tel.: +39.030.9830611 Fax: +39.030.9839207-208 Internet:www.omfb.it e-mail:[email protected] Codice fascicolo:997-400-10810 Rev:AM 300 80 Data: Giovedì 7 settembre 2006 Q (l/min) PORTATA Rev:AG Pump type Velocità max. Velocità max. Velocità continua intermittente Peso min. Max. continuous Max. intermittent Weight Pressione Cilindrata Codice foglio:997-108-01520 Tipo pompa