HDT 84-96-108
Transcript
HDT 84-96-108
FAMILY CODE HDT 84-96-108 BENT AXIS PISTON PUMPS Fluido idraulico Minerale o sintetico compatibile con guarnizioni: Mineral or synthetic compatible with the following seals: HNBR Fluid Temp. consentita -40 +140 °C Allowed temperature Codice fascicolo:997-400-10810 108-013 CODICE FAMIGLIA POMPE A PISTONI AD ASSE INCLINATO Viscosità cinematica T media ambiente (°C) < -40 -40÷10 10÷35 consigliata Average ambient temp. (°C) Kinematic viscosity suggested VG (cSt = mm2/s) 16 22 > 35 32 46 Viscosità cinematica ottimale di esercizio VG= 10 cSt ÷ 100 cSt Viscosità cinematica max consentita all’avviamento VG= 750 cSt Indice di viscosità consigliato VI > 100 Grado di filtrazione > 200 bar: 10 μm < 200 bar: 25 μm 0,85 ÷ 2 bar assoluti/absolut Unidirezionale (Dx o Sx) Optimale kinematic viscosity Max kinematic viscosity suggested at the start-up Viscosity index suggested Oil filtering Pres. di aspirazione Inlet pressure Senso di rotazione Pump rotation Unidirectional (Right or Left) Verificare che la pompa sia posizionata almeno 100 mm sotto il livello minimo del serbatoio olio. Prima di avviare la pompa effettuare spurgo aria. Codice foglio:997-108-01301 Rev:AA Data: Martedì 06 marzo 2012 Verify that pump is, at least, 100 mm under the minimum level of the tank. Before starting the pump bleed the air. Dimensions in mm Tipo pompa Pump type HDT-84 HDT-96 HDT-108 Rotazione Destra Right Rotation Sinistra Left IN OUT IN OUT ISO 228 ISO 228 SAE 24 SAE 16 108-013-08400 108-013-08419 G 1 1/4 G1 108-013-09605 108-013-09614 G 1 1/4 G1 108-013-10808 108-013-10817 G 1 1/4 G1 1 5/8-12 UN-28 1 5/16-12UN-28 1 5/8-12 UN-28 1 5/16-12UN-28 1 5/8-12 UN-28 1 5/16-12UN-28 pag.39 O.M.F.B. S.p.A. Hydraulic Components We reserve the right to make any changes without notice. Edition 2002.11 No reproduction, however partial, is permitted. Via Cave, 7/9 25050 Provaglio d’Iseo (Brescia) Italy Tel.: +39.030.9830611 Fax: +39.030.9839207-208 Internet:www.omfb.it e-mail:[email protected] HDT HDT PISTON PUMP 84-96-108 SERIES SPARE PARTS SCHEMA RICAMBI POMPE A PISTONI HDT 84-96-108 pag.40 O.M.F.B. S.p.A. Hydraulic Components We reserve the right to make any changes without notice. Edition 2002.11 No reproduction, however partial, is permitted. Via Cave, 7/9 25050 Provaglio d’Iseo (Brescia) Italy Tel.: +39.030.9830611 Fax: +39.030.9839207-208 Internet:www.omfb.it e-mail:[email protected] 108 Codice fascicolo:997-400-10810 Data: Martedì 06 marzo 2012 Rev:AA Codice foglio:997-108-01301 Codice foglio:997-108-01301 GAS SAE • • • • • • • • • • • • • • • • • • • • • 21 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • GAS • • • • • • • • • • • • • • • • • • • • SAE • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 23 • • • • • • • SAE • 22 24 25 26 27 28 GAS HDT 108 • • • • • • • • • • • • • • • • • • 29 • • • • • • • • • • • • • • • Descrizione 502-000-01022 501-008-00063 501-000-02729 506-000-24272 501-001-00677 510-002-00220 517-002-01707 501-000-01355 529-007-00226 529-007-01127 511-002-00200 506-000-13137 510-002-00293 525-011-00193 501-003-06142 522-005-00375 542-001-00162 512-005-00812 542-001-00171 501-015-00028 532-005-00034 532-005-00276 532-005-00070 501-023-00037 501-023-00091 501-023-00055 500-029-15086 500-029-15097 500-029-15110 506-000-12387 517-002-01458 116-009-10129 115-006-00135 507-000-00381 500-029-80859 500-029-80868 500-029-80966 500-029-80975 500-029-81107 500-029-81116 501-020-00101 502-004-00574 Description Quantità Quantity Vite TCE M 12x40 Rosetta elastica Anello elastico Paraolio Anello elastico Cuscinetto a rulli conici Corpo anteriore Anello seeger Rondella Rondella Bussola Guarnizione OR Cuscinetto a rulli conici Corona dentata Spina UNI 6364-A Albero Perno sferico con guida albero Molla di carico corpo cilindri Anello guida molla Anello seeger Socket head capscrew Washer Circlip Oil seal Circlip Tapered roller bearing Front housing Retaining ring Washer Washer Bushing O-ring Tapered roller bearing Crown Pin UNI 6364-A Shaft Shaft guide pin Spring Spring guide ring Retaining ring 4 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Pistone sferico Piston 7 Fasce elastiche Spring rings Gruppo corpo cilindri sede pistoni Piston barrel assembly 1 Guarnizione OR Corpo intermedio Rondella acciao-gomma Tappo cieco Guarnizione O-Ring Copper washer Blank plug Gasket 1 1 1 1 1 Gruppo corpo posteriore Rear cover assembly 1 Rosetta SCHNORR Vite TCE M10x45 SCHNORR Washer Socket head capscrew 4 4 Int. housing 21 HDT 30 31 Codice P. Number HDT PISTON PUMP 84-96-108 SERIES SPARE PARTS • • • • • • • • • • • • • • • • • • • • • HDT 96 Codice fascicolo:997-400-10810 SCHEMA RICAMBI POMPE A PISTONI HDT 84-96-108 pag.41 O.M.F.B. S.p.A. Hydraulic Components We reserve the right to make any changes without notice. Edition 2002.11 No reproduction, however partial, is permitted. Via Cave, 7/9 25050 Provaglio d’Iseo (Brescia) Italy Tel.: +39.030.9830611 Fax: +39.030.9839207-208 Internet:www.omfb.it e-mail:[email protected] 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 HDT 84 Data: Martedì 06 marzo 2012 108 N° N° Rev:AA POMPE A PISTONI AD ASSE INCLINATO HDT 108 BENT AXIS PISTON PUMPS CARATTERISTICHE TECNICHE DI FUNZIONAMENTO / TECHNICAL FEATURES cm3/rev 84,2 95.5 107 P1 P3 bar bar 350 370 PORTATA / V1 V2 rpm rpm kg 2300 1500 2000 300 15 FLOW 200 V0=Massima continua vuoto V1=Massima continua V2=Massima intermittente Max. continuous speed without load Max. continuous speed Max. intermittent speed COPPIA ASSORBITA 180 HDT 108 700 HDT 96 650 HDT 108 600 HDT 84 160 HDT 96 550 140 500 120 450 100 400 Nm Q (l/min) Min. speed DRIVE TORQUE 220 80 HDT 84 350 60 300 40 250 20 200 150 500 1000 1500 2000 2500 100 rpm 50 POTENZA ASSORBITA 50 POWER INPUT 110 90 350 bar 80 300 bar 70 50 200 bar 40 150 bar 30 100 bar 20 10 100 150 200 MOMENTO PESO / MASS MOMENT Mamm.= s x G (Nm) G=Peso in N (Peso in Kg x 9.81) Baricentro Center of mass s=120.4mm G G=Weight in N (Weight in Kg x 9.81) 200 250 300 350 400 Seal Kit 108-903-85008 SCELTA DEL TUBO DI ASPIRAZIONE HOW TO CHOOSE THE SUCTION PIPE SIZE Q Portata ∅ interno min. tubo Flow 50 150 Kit guarnizioni / 250 bar 60 100 bar 400 bar 100 kW Peso rpm 240 Q (l/min) Weight V0 260 rpm Velocità min. rpm P1=Pressione massima continua Max. continuous pressure (100%) P3=Pressione massima di punta Max. peak pressure (6 sec.max) 280 / Speed Min pipe diam. Velocità flusso Flow speed l/min mm inch (m/s) 20 25 1” 0,68 30 32 0,62 1” 1/4 40 32 0,83 50 38 0,74 1” 1/2 60 38 0,88 70 40 1” 9/16 0,93 80 45 0,84 1” 3/4 90 45 0,94 100 50 0,85 2” 110 50 0,93 120 60 0,71 130 60 0,77 2” 3/8 140 60 0,83 150 60 0,88 160 63 0,86 170 63 0,91 2” 1/2 180 63 0,96 Per garantire corrette condizioni di aspirazione la velocità del flusso non deve superare 1 m/sec. To ensure the proper suction pipe size the flow speed should not exceed 1mt/sec. pag.42 O.M.F.B. S.p.A. Hydraulic Components We reserve the right to make any changes without notice. Edition 2002.11 No reproduction, however partial, is permitted. Via Cave, 7/9 25050 Provaglio d’Iseo (Brescia) Italy Tel.: +39.030.9830611 Fax: +39.030.9839207-208 Internet:www.omfb.it e-mail:[email protected] Data: Martedì 06 marzo 2012 HDT-84 HDT-96 HDT-108 Velocità Pressure RevAA Pump type Pressione Codice fascicolo:997-400-10810 Cilindrata Displacement Codice foglio:997-108-01301 Tipo pompa