POWER PEAK 1 Plus
Transcript
POWER PEAK 1 Plus
Bedienungsanleitung Operating instructions Notice d’utilisation Manuale d’istruzione POWER PEAK 1 Plus No. 8424 Bedienungsanleitung Bestell Nr. POWER PEAK 1 Plus 8424 Allgemeines Der POWER PEAK 1 PLUS ist für das Schnelladen und Entladen von 4 bis 7-zelligen NICD- oder NIMH-Akkus geeignet. Die Abschaltung erfolgt bei vollgeladenem Akku nach der Delta-Peak-Methode. Das Gerät ist für den Betrieb an einer 12V Bleibatterie oder einem entsprechend leistungsfähigen, gut stabilisierten 12V oder 13,8 V Netzteil vorgesehen. Sicherheitshinweise - Bei längerem Nichtgebrauch das Ladegerät von der Spannungsquelle trennen und eventuell angeschlossene Akkus abnehmen. - Auf freie Kühlöffnungen zur Luftzirkulation achten. – Nicht auf Teppich oder Filz stellen. - Ladegerät und Akkus nicht auf brennbaren Unterlagen betreiben und nicht unbeaufsichtigt lassen. - Vor Feuchtigkeit schützen. - Auf richtige Polung aller Anschlüsse und Ausgänge achten. - Kurzschlüsse vermeiden. - Nicht direkter Sonneneinstrahlung aussetzen, Gerät nicht abdecken. - Keine Akkus laden, die stark erwärmt sind. Akkus auf Umgebungstemperatur abkühlen lassen. - Nur schnelladefähige und formierte Akkus verwenden. - Es dürfen nur Zellen gleicher Kapazität und gleichen Fabrikats im Verbund geladen werden. - Nicht zwei Akkus zum Laden parallel schalten. - Nur zum Laden von wiederaufladbaren Akkus geeignet. - Ladeströme der Höchstbelastung der am Akku befindlichen Kabel und Steckverbindungen anpassen. - Ausgang und Eingang nicht miteinander verbinden. Technische Daten ca. 11 V....15 V DC 12V Bleibatterie oder gut stabilisiertes 13,8V Netzteil (kein Ladegerät für Autobatterien verwenden!) Akkunennspannung: 4,8 V ... 8,4 V Ladestrom: 1 A ... 1,5 A für 4- ... 5-zellige Akkus 1 A ... 4,5 A für 6- ... 7-zellige Akkus Abschaltautomatik Laden: Delta-Peak-Verfahren Erhaltungsladestrom: ca. 180 mA Entladestrom: ca. 0,6 A ... 1,2 A, abhängig von Zellenzahl Abschaltung beim Entladen: automatisch, bei ca. 0,8 V / Zelle Schutzfunktionen: Ein- und ausgangsseitiger Verpolschutz, ausgangsseitiger Kurzschlußschutz Sicherung : 10 A Kfz-Sicherung Abmessung: ca. 140 x 110 x 55 mm Gewicht: ca. 350g Betriebsspannung: 3 Bedienungsanleitung Bestell Nr. POWER PEAK 1 Plus 8424 Bedienelemente LCD-Display DISCHARGING-LED FAST-CHARGING-LED SLOW-CHARGING-LED Sicherung Stromversorgung MODE-Taste Ladeausgang NICD/NIMH Umschalter Ladestromsteller Inbetriebnahme - - Krokodilklemmen der Stromversorgung an eine 12 V Bleibatterie oder ein entsprechendes Netzteil anschließen, unbedingt auf richtige Polung achten (rot = plus / schwarz = minus) - siehe auch Absatz „Netzteil“. Im LC-Display erscheint „0000“, die LEDs sind dunkel. Ladekabel polrichtig (rot = plus / schwarz = minus) an die Buchsen des Ladeausgangs anschließen. Das Ladegerät verfügt über die Funktionen Laden, Entladen, Entladen-vor-Laden und zyklisches Entladen-vor-Laden. Um eine dieser Funktionen zu aktivieren, sind die folgenden Schritte auszuführen: - - Auswahl des Akkutyps mittels des NICD / NIMH Schiebeschalters. Anschließen des Akkus an das Ladekabel. Unbedingt auf richtige Polung achten! Es ertönt ein Beep und die grüne SLOW-CHARGING-LED blinkt als Zeichen für Erhaltungsladung. Einstellen des Ladestroms am LADESTROMSTELLER. Dabei ist unbedingt zu beachten, daß 4- oder 5-zellige Akkus nur mit maximal 1,5 A geladen werden dürfen. Außerdem darf die maximale Laderate von 4- oder 5-zelligen NIMH-Akkus 1C nicht überschreiten, z. B. 1,0 A bei 1000 mAh Akkukapazität. 4 Bedienungsanleitung Bestell Nr. POWER PEAK 1 Plus 8424 Laden MODE-Taste einmal kurz betätigen. Es ertönt ein kurzer Beep als Quittung, die rote FASTCHARGING-LED leuchtet. Der Akku wird mit dem eingestellten Strom geladen. Das Display zeigt die eingeladene Kapazität an. Der Ladevorgang wird bei vollgeladenem Akku durch die Delta-Peak-Abschaltautomatik beendet. Entladen MODE-Taste ca. 2 Sekunden gedrückt halten. Es ertönen zwei kurze Beep als Quittung, die gelbe DISCHARGING-LED leuchtet. Der Akku wird mit ca. 1 A (spannungsabhängig) entladen. Das Display zeigt die entladene Kapazität an. Der Entladevorgang wird bei einer Akkuspannung von ca. 0,8 V pro Zelle beendet. Entladen-vor-Laden MODE-Taste zweimal kurz betätigen. Es ertönen drei kurze Beep als Quittung. Es wird ein Entladevorgang gefolgt von einem Ladevorgang ausgeführt. Das Display zeigt, entsprechend der aktiven Funktion, die eingeladene bzw. entladene Kapazität an. Der jeweilige Ladezustand wird durch die DISCHARGING-LED oder die CHARGING-LED angezeigt. Zyklisches Entladen-vor-Laden Den Zyklus nach dem Formieren zum Auffrischen älterer Akkus maximal 3 bis 5 mal anwenden. MODE-Taste zweimal betätigen, beim zweiten Betätigen zwei Sekunden gedrückt halten. Es ertönen vier kurze Beep. Es werden endlos Entladen-vor-Laden-Zyklen ausgeführt. Das Display zeigt, entsprechend der aktiven Funktion, die eingeladene bzw. entladene Kapazität an. Die Funktionen werden entweder automatisch oder durch Betätigung der MODE-Taste beendet und durch zwei lange Beep quittiert. Im Falle einer automatischen Abschaltung ertönt alle zehn Sekunden ein Beep. In allen Fällen befindet sich das Ladegerät nach der Abschaltung im Zustand der Erhaltungsladung, die grüne LED blinkt und im Display ist der zum Zeitpunkt der Abschaltung eingeladene bzw. entladene Kapazitätswert gespeichert. Dieser Kapazitätswert wird entweder durch Anschließen eines Akkus oder durch Umschalten von Laden auf Entladen oder umgekehrt gelöscht. Mögliche Fehlerursachen - SLOW-CHARGING-LED blinkt, MODE-Taste reagiert nicht: Akku verpolt oder Kurzschluß am Ladeausgang. SLOW-CHARGING-LED blinkt nicht: Unterbrechung zum Akku oder defekte Sicherung. 5 Bedienungsanleitung Bestell Nr. POWER PEAK 1 Plus 8424 Allgemeines über das Laden und Entladen von Akkus Grundsätzlich sind die Hinweise der Akkuhersteller zu beachten, insbesondere die Hinweise über maximale Ladeströme. Um sicherzustellen, daß die Delta-Peak-Automatik optimal arbeiten kann, dürfen nur formierte Akkus schnellgeladen werden, d.h. neue oder längere Zeit nicht benutzte Akkus müssen in regelmäßigen Zeitabständen entladen und mit kleinen Laderaten, typischerweise C/10 (Erhaltungsladung) formiert werden. Dazu Akku anschließen und MODE-Taste nicht betätigen. Ein gelegentlich vollständiges Entladen wirkt auch dem MEMORY-EFFEKT entgegen. Anmerkungen - Blinken der FAST-CHARGING-LED zeigt an, daß die Abschaltautomatik aktiviert ist. Beim Laden von 7-zelligen Akkus kann es vorkommen, daß der Ladestrom gegen Ende der Ladung absinkt. Das Beenden das Ladens bzw. Entladens soll nicht durch Abziehen des Akkus erfolgen. Immer mit der MODE-Taste beenden. Netzteil - Durch Anschluß des Power Peak 7A Netzteils, Bestell Nr. 8415 kann das Ladegerät auch am 230 Volt Netz betrieben werden und wird dadurch zu einem universellen 230 V-AC und 12 V-DC Ladegerät. robbe Modellsport GmbH & Co. KG Technische Änderungen vorbehalten 6 Operating instructions Order No. POWER PEAK 1 Plus 8424 Introduction The POWER PEAK 1 PLUS is designed for fast-charging and discharging NICD and NIMH battery packs consisting of 4 to 7 cells. When the pack is fully charged the process is terminated by the Delta Peak method. The unit is designed for use with a 12 V lead-acid battery or a powerful well stabilised mains PSU rated at 12 V or 13.6 V. Safety notes - If the charger is not to be used for a protracted period, disconnect it from the power source and remove any battery packs connected to it. - Be sure to keep the cooling slots unobstructed to provide good air circulation - don’t stand the charger on a carpet or felt surface. - Do not set up the charger and batteries on a flammable surface, and never leave the unit operating unsupervised. - Protect the unit from damp. - Take care to maintain correct polarity at all connections and outputs. - Avoid short-circuits. - Don’t subject the charger to direct sunshine, and do not cover it. - Do not charge batteries which are already hot; allow them to cool down to ambient temperature before recharging. - Use only packs of fast-charge cells which have been properly balanced (equal state of charge). - Packs must consist of cells of the same make, type and capacity. - Do not wire two packs together in parallel for charging. - The unit is only suitable for use with rechargeable batteries. - Set charge currents within the maximum rated capacity of the cables and connectors attached to the battery pack. - Never connect any charger output to the input. Specification Operating voltage: approx. 11 V ... 15 V DC 12 V lead-acid battery or a powerful well stabilised mains PSU (do not use a car battery charger!) Nominal battery voltage: 4.8 V ... 8.4 V Charge current: 1 A ... 1.5 A for 4-cell / 5-cell batteries 1 A ... 4.5 A for 6-cell / 7-cell batteries Automatic charge termination: Delta Peak process Trickle charge current: approx. 180 mA Discharge current: approx. 0.8 A ... 1.2 A, depending on cell count Discharge termination: automatic, at approx. 0.8 V / cell Protective functions: Polarity protection at input and output, short-circuit protection on output Fuse: 10 A car fuse Dimensions: approx. 140 x 110 x 55 mm Weight: approx. 350 g 7 Operating instructions Order No. POWER PEAK 1 Plus 8424 Charger controls LCD screen DISCHARGING-LED FAST-CHARGING-LED SLOW-CHARGING-LED Fuse Power supply MODE button Charge output NICD/NIMH select switch Charge current knob Using the charger - - Connect the crocodile clips to a 12 V lead-acid battery or a suitable mains PSU; take great care over correct polarity (red = positive / black = negative); see section entitled “Mains PSU”. The LCD screen will show “0000”, and the LEDs will remain off. Connect the charge leads to the charge output sockets with correct polarity (red = positive / black = negative). The charger features the following functions: Charge, Discharge, Discharge-before-Charge and cyclic Discharge-before-Charge. The following steps are required to activate these functions: - - Select the battery type using the NICD / NIMH slide switch. Connect the battery pack to the charge lead, taking great care over correct polarity. The unit emits a beep, and the green SLOW CHARGING LED flashes to indicate that trickle charging is taking place. Set the charge current on the CHAR CURRENT KNOB. Note that 4-cell and 5-cell packs must be charged at no more than 1.5 A. Moreover the maximum charge rate for 4-cell and 5-cell NIMH batteries must not exceed 1C, e.g. 1.0 A for a battery of 1000 mAh capacity. 8 Operating instructions Order No. POWER PEAK 1 Plus 8424 Charging Press the MODE button once briefly. You will hear a short beep in confirmation, and the red FAST CHARGING LED will glow. The battery is now charged at the set current, and the screen displays the charged-in capacity. The charge process is terminated by the automatic Delta Peak circuit when the pack is fully charged. Discharging Hold the MODE button pressed in for about two seconds. You will hear two short beeps in confirmation, and the yellow DISCHARGING LED will glow. The battery is discharged at around 1 A (voltage-dependent), and the screen displays the discharged capacity. The discharge process is terminated at a battery voltage of around 0.8 V per cell. Discharge-before-Charge Press the MODE button twice briefly. You will hear three short beeps in confirmation, and the charger carries out a discharge process followed by a charge process. The screen displays the charged-in or discharged capacity according to the active function. The DISCHARGING LED or the CHARGING LED lights up to indicate which phase is in progress at any time. Cyclic Discharge-before-Charge The cycle function can be used to rejuvenate older batteries once the pack has been balanced; we recommend three to max. five cycles. Press the MODE button twice, holding it pressed in for two seconds the second time. You will hear four short beeps, and the charger embarks on an infinite number of dischargebefore-charge cycles. The screen displays the charged-in or discharged capacity according to the active function. The functions are either terminated automatically or by the operator pressing the MODE button, in which case you will hear two long beeps in confirmation. If the charger switches off automatically you will hear one beep every ten seconds. In all cases the charger reverts to trickle charge mode after termination, the green LED flashes and the screen shows the stored charged-in or discharged capacity value at the time of the termination. This capacity value is erased when you either connect a battery pack, or you switch from Charge to Discharge or vice versa. Fault-finding - SLOW CHARGING LED flashes, charger does not respond to MODE button. Battery connected with reverse polarity, or short-circuit present at charge output. SLOW CHARGING LED does not flash: interruption in battery lead, or fuse blown. 9 Operating instructions Order No. POWER PEAK 1 Plus 8424 General information about charging and discharging batteries As a basic rule please be sure to observe the battery manufacturer’s recommendations, especially the information regarding maximum charge currents. To ensure that the automatic Delta Peak circuit is able to work as efficiently as possible, only properly balanced packs should be fast-charged. This means that new packs, and packs which have not been used for a long time, should be discharged at regular intervals and re-balanced by slow-charging at a low rate, typically C/10. To do this connect the battery and press the MODE button. An occasional complete discharge process also helps to avoid and/or eliminate the MEMORY EFFECT. Notes - If the FAST CHARGING LED flashes, this indicates that the automatic charge termination circuit is active. - When 7-cell battery packs are being charged you may find that the charge current declines towards the end of the charge process. - Don’t end the charge or discharge process simply by disconnecting the battery pack; always stop the process by pressing the MODE button. Mains PSU - If you use the Power Peak 7A mains PSU, Order No. 8415, the charger can also be operated from the 230 Volts mains supply, turning it into a universal 230 V AC and 12 V DC charger. robbe Modellsport GmbH & Co. KG We reserve the right to alter technical specifications. 10 Notice d’utilisation Réf. POWER PEAK 1 Plus 8424 Généralités Avec le chargeur POWER PEAK 1 PLUS est conçu pour la charge rapide et la décharge d’accus de 4 à 7 éléments Cd-Ni ou NiMH. La commutation en fin de charge, lorsque l’accu est parfaitement chargé, intervient par l’intermédiaire de la procédure Delta-Peak. L’appareil est conçu pour un fonctionnement avec un accu 12 volts de voiture ou un bloc d’alimentation secteur puissant et parfaitement stabilisé sur 13,8 volts. Consignes de sécurité : - Lorsqu’il est prévu de ne pas utiliser l’appareil pendant un certain temps, le désolidariser du secteur et en retirer les accus encore en place. Veiller à laisser dégagées les fentes de refroidissement afin de permettre à l’air de circuler. Ne pas l’installer sur un tapis ou du feutre pour une procédure d charge. Ne pas disposer les accus et l’appareil sur un support inflammable et ne jamais les laisser sans surveillance. Protéger le chargeur de l’humidité. Observer les polarités de tous les branchements et les sorties. Lorsque les accus sont mis en place avec une polarité inversée, le fusible saute. Éviter les courts-circuits. Ne jamais exposer l’appareil au rayonnement direct du Soleil. Ne pas couvrir l’appareil lorsqu’il est en service. Ne pas mettre en charge des accus particulièrement chauds. Avant de les charger, laisser refroidir les accus à température ambiante. N’utiliser que des accus propres à une charge rapide et parfaitement homogènes. N’utiliser que des éléments de capacité égale et de même fabrication assemblés en accus. Ne pas raccorder deux accus en parallèle pour les charger. Le chargeur n’est conçu que pour la charge d’accu effectivement rechargeables. Ajuster les courants de charge les plus élevés aux connecteur et cordon solidaires des accus. Ne pas raccorder entre elles les entrées et les sorties. Caractéristiques techniques Tension de service : approx. 11 à 15 volts CC, accu 12 volts de voiture ou bloc d’alimentation secteur puissant et parfaitement stabilisé sur 13,8 volts (ne pas utiliser de chargeur pour batterie de voiture). Tension nominale de l’accu : 4,8 à 8,4 volts Courant de charge : 1 A à 1,5 A pour des accus de 4 à 5 éléments 1 A à 4,5 A pour des accus de 6 à 7 éléments Commutation automatique : procédure Delta-Peak en fin de charge Courant de charge de maintien : approx. 180 mA Courant de décharge : approx. 0,6 A à 1,2 A, en fonction du nombre d’éléments Commutation en fin de décharge : automatique à approx. 0,8 volt par élément 11 Fonctions de protection : Fusible : Encombrement : Poids : Notice d’utilisation Réf. POWER PEAK 1 Plus 8424 protection contre les inversions de polarité des entrées et des sorties, protection contre les courts-circuits côté sortie. 10 A, fusible de voiture approx. 140 x 110 x 55 mm approx. 350 g Éléments de commande Ecran LED DE DÉCHARGE LED DE CHARGE RAPIDE LED DE CHARGE LENTE Fusible Alimentation Touche de sélection du MODE Commutateur Cd-Ni/NiMH Potentiomètre du courant de charge Sortie de charge Mise en service - Raccorder les pinces crocodile à une batterie au plomb de 12 volts ou à bloc d’alimentation secteur approprié ; veiller absolument à respecter les polarités (rouge = plus / noir = moins) - cf. également le paragraphe « Bloc d’alimentation secteur ». - Sur l’écran apparaît la mention « 0000 » les LED sont éteintes. - Raccorder le cordon de charge en respectant les polarité (rouge = plus / noir = moins) aux douilles de sortie. Le chargeur dispose des fonctions charge, décharge, décharge avant charge et décharge cyclique avant charge. Marche à suivre pour activer l’une de ces fonctions. - - Sélectionner le type d’accu à l’aide du curseur CDNI/NIMH. Raccorder l’accu au cordon de charge. Veiller absolument à respecter les polarités ! Un bip retentit et la LED verte SLOW-CHARGING clignote pour indiquer que la charge de maintien est activée. Régler le courant de charge au niveau du potentiomètre de sélection du courant de charge. Observer impérativement que les accus de 4 ou 5 éléments ne peuvent 12 Notice d’utilisation Réf. POWER PEAK 1 Plus 8424 être chargé qu’avec un courant maximal de 1,5 A. Par ailleurs, le taux de charge maximal d’accus de 4 ou 5 éléments NiMH 1C ne doit pas être dépassée, par exemple 1,0 A avec un capacité d’accu de 1000 mAh. Charge Actionner brièvement la touche MODE. Un bip court retentit pour valider la sélection, la LED rouge FAST-CHARGING s’allume. La charge de l’accu commence avec le courant programmé. L’écran présente la capacité chargée. La procédure de charge est achevée lorsque l’accu est complètement chargé par le dispositif Delta-Peak de commutation en fin de charge. Décharge Maintenir la touche MODE enfoncée pendant deux secondes environ.. Deux bips courts retentissent pour valider la sélection, la LED jaune DISCHARGING s’allume. L’accu est déchargé avec environ 1 A (dépend de la tension). L’écran présente la capacité déchargée. La procédure de décharge est interrompue lorsque la tension par élément est de 0,8 volt. Décharge avant charge Actionner deux fois brièvement la touche MODE. Deux bips courts retentissent valider la sélection. Une décharge est engagée avant une charge. L’écran présente, en fonction de la procédure en cours, la capacité déchargée puis la capacité chargée. L’état en cours est indiqué par la LED DISCHARGING puis par la LED CHARGING. Décharge avant charge cyclique Après avoir homogénéisé les éléments, pour rafraîchir les accus appliquer un cycle de 3 à 5 décharges avant charges. Actionner deux fois la touche MODE et maintenir la pression pendant deux secondes lors de la deuxième pression. Quatre bips courts retentissent. Un cycle infini de décharges avant charges est engagé. L’écran présente, en fonction de la procédure en cours, la capacité déchargée puis la capacité chargée. Les fonctions sont achevées soit automatiquement soit en actionnant la touche MODE ce qui est validé par deux bips longs. En cas de commutation automatique en fin de charge, toutes les dix secondes retentit un bip. Dans tous les cas, après la commutation, le chargeur se trouve en état de charge de maintien, la LED verte est allumée et l’écran mémorise présente la capacité chargée ou déchargée au moment de l’arrêt. Cette valeur de capacité est effacée lorsqu’on raccorde un nouvel accu ou en commutation de charge sur décharge ou inversement. Origine possible des anomalies - La LED SLOW CHARGING clignote, la touche MODE ne réagit pas ; l’accu est raccordé avec les polarités inversées ou présence d’un court-circuit à la sortie de charge. - La LED SLOW CHARGING ne clignote pas. Rupture du cordon vers l’accu ou fusible défectueux. 13 Notice d’utilisation Réf. POWER PEAK 1 Plus 8424 Généralités concernant la charge et la décharge d’accus Il faut en règle générale observer formellement les recommandations du fabricant de l’accu, particulièrement en ce qui concerne les courants de charge maximaux. Pour s’assurer que le dispositif de commutation automatique Delta-Peak en fin de charge fonctionne correctement, il ne faut mettre en charge rapide des accus dont les éléments sont parfaitement homogènes, c’est-à-dire que les accus neufs ou qui n’ont pas été utilisés depuis un certain temps doivent être déchargés à intervalles réguliers ou être formés avec de petits chargeurs assurant une charge de type C/10. Pour ce faire, branchez ces accus sur l’appareil sans en actionner la touche MODE. Une décharge complète de temps en temps a aussi un effet contre l’effet de mémoire des accus. Remarques - Le clignotement de la LED FAT-CHARGING indique que la commutation automatique est activée. Lors de la charge d’accus de 7 éléments, il peut se produire que le courant de charge chute vers la fin de la charge. La fin de la charge ou de la décharge ne doit jamais intervenir en retirant l’accu du chargeur. La stopper à l’aide de la touche MODE. Bloc d’alimentation secteur - La mise en place du bloc d’alimentation secteur Power Peak 7A, réf. 8415 permet également d’utiliser le chargeur avec le réseau 230 volts ce qui en fait un chargeur universel aussi bien adapté au secteur 230 volts CA qu’au courant continu 12 volts. robbe Modellsport GmbH & Co. KG Sous réserve de modification technique. 14 Manuale d’istruzione Codice POWER PEAK 1 Plus 8424 Introduzione Il POWER PEAK PLUS 1 è un caricabatteria progettato la corretta ricarica e scarica rapida nonché manutenzione delle batterie NICD e/o NIMH. Può analizzare, caricare e scaricare pacchi da un minimo di 4 a 7 celle massimo. Il fine carica è gestito dal sistema a lettura di picco “Delta Peak “. Il dispositivo è concepito per essere utilizzato con alimentazione a 12Vcc di una normale batteria al piombo oppure di un alimentatore stabilizzato con tensione d’uscita compresa tra 12 e 13,6 V. Norme di Sicurezza - Se il caricabatteria rimane inutilizzato per un periodo prolungato è consigliabile sconnetterlo dall’alimentazione di ingresso e scollegare ogni batteria collegata in uscita per un’eventuale ricarica. - Assicurarsi di mantenere le feritoie di aerazione pulite e senza impedimento alcuno al fine di assicurare una corretta circolazione d’aria per il raffreddamento. - Non utilizzare il caricabatteria appoggiato ad una superficie infiammabile e non lasciare mai l’apparecchio incostudito durante il processo di carica-scarica. - Proteggere l’apparecchio da eventuali urti - Prestare attenzione a non invertire le polarità d’ingresso od uscita. - Evitare corti circuiti - Non lasciare il caricabatteria al sole ed evitare di coprirlo durante l’uso - Non caricare batterie già calde: lasciarle raffreddare fino alla temperatura ambiente prima di ricaricarle - Utilizzare solo pacchi a carica rapida precedentemente “bilanciati” con una carica-scarica lenta. - I pacchi devono essere formati da celle uguali tra loro: non mescolare celle di capacità e marche diverse. - Non collegare due pacchi in parallelo per la ricarica - Il POWER PEAK 1 PLUS è progettato solamente per batterie ricaricabili. - Selezionare correnti di carica comprese nei valori massimi suggeriti dal costruttore e proporzionati al cavo e connettore della batteria utilizzata. - Mai collegare un altro caricabatteria all’uscita. Specifiche Tensione di alimentazione : 11 V ... 15 V DC circa Batteria al piombo o alimentatore stabilizzato e ben filtrato alimentato a rete. (non utilizzare mai un carica batterie 12V d’auto) Tensione nominale di batteria in uscita : 4.8 V ... 8.4 V Corrente di carica : 1 A ... 1.5 A per pacchi da 4 - 5 celle 1 A ... 4.5 A per batterie con 6- 7celle Interruzione carica: a lettura di picco “ Delta Peak “ Carica di mantenimento: 180 mA circa Corrente di scarica : 0.8 A ... 1.2 A circa, in ragione del numero di celle. Interruzione scarica : automatica a 0.8 V per cella circa Protezioni: Inversione di polarità ingresso uscita, corto circui to in uscita, Fusibile: 10 A da macchina Dimensioni: 140 x 110 x 55 mm Peso: 350 g circa 15 Manuale d’istruzione Codice POWER PEAK 1 Plus 8424 Uso del caricabatteria Schermo LCD LED SCARICA LED CARICA RAPIDA LED CARICA LENTA Fusibile Alimentazione Tasto MODE Uscita Selettore NICD/NIMH Manopola reg. Corrente - Connettere I coccodrilli d’ingresso alla batteria 12 V oppure ad un appropriato alimentatore stabilizzato prestando particolare attenzione alla polarità. Lo schermo a cristalli liquidi LCD mostrerà la scritta “0000” e il diodo LED di carica rimarrà spento. Collegare I cavi di ricarica alle boccole d’uscita del caricabatteria rispettando anche in questo caso le polarità. (Rosso = positivo. Nero = negativo) Il caricabatteria offre le seguenti opzioni: CARICA (CHARGE), SCARICA (DISCHARGE), SCARICA PRIMA di CARICARE e ciclo (DISCHARGE BEFORE). Per attivare l’opzione desiderata seguire i passaggi successivi. - Selezionare il tipo di batteria da caricare utilizzando il selettore NICD / NIMH. Collegare il pacco batterie al cavo di ricarica, avendo cura di rispettare le polarità. Il POWER PEAK 1 Plus emetterà un “beep” e il LED VERDE DI CARICA LENTA inizierà a lampeggiare indicando appunto l’inizio della carica lenta di mantenimento. - Fissare la corrente di carica ruotando l’apposita manopola. Si noti che pacchi di 4-5 celle devono essere caricati con correnti non superiori a 1.5 A. Si noti anche che la corrente massima di carica per pacchi NIMH di 4-5 celle non deve superare la capacità di batteria 1C, ad esempio 1.0 A per una batteria di 1000 mAh di capacità. 16 Manuale d’istruzione Codice POWER PEAK 1 Plus 8424 Carica Premere il tasto “MODE” brevemente una volta. Si udirà un “beep” a conferma e il LED ROSSO di CARICA RAPIDA si accenderà. La batteria è ora in carica con il valore di corrente impostato e lo schermo LCD mostra la quantità di carica immagazzinata espressa in mA. La carica sarà interrotta al raggiungimento del picco massimo con lettura dello stesso a pacco completamente carico. Scarica Tenere premuto il tasto “MODE” per due secondi circa. Due brevi “beep” confermeranno l’inizio della scarica e il DIODO LED GIALLO di SCARICA risulterà acceso. La batteria verrà scaricata con una corrente di 1 A circa (dipende dalla tensione batteria) e lo schermo LCD visualizzerà la capacità di scarica. Il processo di scarica viene interrotto al raggiungimento di una tensione minima di 0,8 V per elemento. Scarica prima della Carica Premere il tasto MODE brevemente per due volte. Tre brevi “beep” segnaleranno l’inizio del processo di scarica-carica. Lo schermo LCD visualizzarà il valore di “capacità di scarica o carica” in ragione del processo in corso (scarica o carica). Il LED di SCARICA o il LED di CARICA indicheranno se il POWER PEAK sta scaricando o caricando. Ciclo di Scarica- Carica La funzione ciclo può essere utilizzata per “ripristinare” ed eseguire la manutenzione di vecchie batterie dopo che avere eseguito il loro “bilanciamento”. Si raccomanda di eseguire al massimo 5 cicli. Premere il tasto MODE per due volte e mantenerlo premuto per due secondi. Quattro brevi “beep” segnaleranno l’inizio di una serie infinita di cicli di scarica-carica. Lo schermo visualizzarà la capacità di carica o scarica in ragione del tipo di processo in atto. Entrambi le funzioni (carica o scarica) possono concludersi automaticamente o manualmente premendo il tasto MODE. In questo caso due lunghi beep confermeranno l’interruzione del processo. Se il caricabatteria terminerà il processo automaticamente un segnale acustico, emesso ogni dieci secondi, né segnalerà la fine. In ogni caso il caricabatteria commuterà in carica di mantenimento (DIODO LED VERDE LAMPEGGIANTE) a fine carica e lo schermo mostrerà la quantità di corrente immagazzinata o la capacità di scarica ottenuto alla fine della scarica. Questo dato verrà rimarrà memorizzato e sarà cancellato solo collegando un nuovo pacco oppure commutando da CARICA a SCARICA o viceversa. Ricerca guasti - Il LED DI CARICA lampeggia e il caricabatteria non risponde al tasto MODE: la batteria è collegata con polarità invertita oppure esiste un corto circuito in uscita. LED CARICA LENTA non lampeggia: interruzione del cavo di collegamento della batteria oppure il fusibile è bruciato. 17 Manuale d’istruzione Codice POWER PEAK 1 Plus 8424 Informazioni generali sulla carica e scarica delle batterie Come regola generale assicuratevi di osservare le raccomandazioni del costruttore delle batterie in vostro possesso e che vi accingete a ricaricare prestando particolare attenzione alla corrente massima di carica. Per essere sicuri che il sistema a lettura di picco funzioni correttamente si raccomanda di caricare con carica rapida solo pacchi bilanciati. Questo significa che ogni nuovo pacco o pacchi rimasti inattivi per un lungo periodo dovrebbero essere scaricati ad intervalli regolari e ricaricati con carica lenta con corrente pari a 1/10 della capacità nominale prima di essere sottoposti alla carica rapida. Per ottenere ciò collegate la batteria al caricabatteria e premete il tasto MODE. Una scarica completa, da ripetersi di tanto in tanto, aiuterà anche a prevenire ed eliminare il tipico EFFETTO MEMORIA delle batterie NICD. Alcune note - Se il DIODO LED di CARICA RAPIDA lampeggia significa che il circuito automatico di fine carica è attivo. - Durante la ricarica di un pacco di 7 celle è possibile rilevare un abbassamento della corrente di carica verso la fine del processo. - Non interrompere la carica o scarica di un pacco scollegando il pacco stesso. Per interrompere la carica premere sempre il pulsante MODE. Alimentazione d’ingresso - Se si sta utilizzando l’alimentatore POWER PEAK 7A, codice N.8415, il caricabatteria può essere alimentato dalla normale rete di 220 –230 Vca trasformando così il POWER PEAK 1 Plus in un caricabatteria universale 12 Vcc e 220 Vca. robbe Modellsport Gmbh & Co. KG Tutti I diritti riservati 18 robbe Modellsport GmbH & Co. KG Metzloserstr. 36 Telefon: 06644 / 87-0 36355 Grebenhain CAC