Manuale d`uso modem DEA718 Telit GT863-PY
Transcript
Manuale d`uso modem DEA718 Telit GT863-PY
Manuale d’uso modem DEA718 Telit GT863-PY per strumenti E/R/M-Log Introduzione Il presente manuale descrive come installare e configurare il modem DEA718 per l’uso con strumenti di tipo E/R/M-Log. 1 - Configurazione modem Il modem DEA718 è fornito da LSI LASTEM già configurato per il funzionamento in modalità GSM. Per consentire la trasmissione GPRS con protocolli TCP o FTP è necessario modificare il file config.ini tramite il programma di emulazione terminale rsterm (disponibile sul DVD MW6501 nella cartella Install\Support\RSTerminal). La modifica del file può essere fatta con un editor di testi come ad esempio “Blocco note” di Windows. 1.1 – Trasferimento del file config.ini dal modem al PC Per trasferire il file config.ini dal modem al PC procedere come segue: 1. Avviare il programma rsterm, scegliere il menu Init, selezionare la porta seriale a cui si intende collegare il modem (ad esempio COM1), impostare Baudrate a 115200 e Flowcontrol a Hardware e premere il pulsante [Open]; 2. Collegare il modem al cavo seriale ELA105 fornito insieme ad E/R/M-Log e solo successivamente accenderlo: il modem a seguito delle precedenti operazioni si avvia in modalità comando ed è quindi disponibile ad essere configurato; 3. Dal menu Init premere il pulsante [AT] ed attendere la risposta “OK” dal modem; 4. Assicurarsi che il testo del primo pulsante in basso a sinistra sia AT#SELINT=2; in caso contrario impostare 2 nel rispettivo menu a discesa; premere il pulsante [AT#SELINT=2] ed attendere “OK” dal modem; 5. Scegliere il menu Telit Python; premere il pulsante [AT#LSCRIPT] ed attendere che la lista Files in module visualizzi i file del modem (_crcfun.pyo, common.pyo, config.ini, ecc.); 6. Premere il collegamento ipertestuale Working folder, click to change, scegliere la cartella dove verrà copiato il file di configurazione (ad esempio “c:\temp”); assicurarsi che nella casella bianca alla sinistra di R ci sia il carattere * (asterisco); se non fosse presente inserirlo e premere il bottone [R] alla sua destra; selezionare il file config.ini nella lista Files in module; premere il pulsante [Download selected file(s) from module to PC] e scegliere Sì per proseguire; il messaggio Done! avvisa che l’operazione è andata a buon fine; 7. Scegliere il menu Init, premere il pulsante [Close] e chiudere infine il programma rsterm. 1.2 – Modifica del file config.ini per la connessione alla rete GPRS Per permettere il collegamento del modem alla rete GPRS è necessario modificare i parametri della sezione GPRS in base al gestore della SIM utilizzata. Sezione [GPRS] Nome parametro APN USER PASSWORD Esempio ibox.tim.it 1234567890 *) Descrizione E’ l’Access Point Name da utilizzare per la connessione GPRS E’ il Nome utente da utilizzare per la connessione GPRS E’ la Password da utilizzare per la connessione GPRS Di seguito sono riportati i dati relativi alle configurazioni GPRS dei principali gestori italiani: TIM ibox.tim.it numero telefonico della SIM *) APN Nome Utente Password VODAFONE internet lasciare vuoto lasciare vuoto WIND internet.wind lasciare vuoto lasciare vuoto 1.3 – Modifica del file config.ini per la trasmissione dei dati con protocollo TCP Per la trasmissione dei dati con protocollo TCP è necessario modificare i parametri specificati nella seguente tabella: Sezione [SERVER] IP Nome parametro Esempio 192.168.1.1 Descrizione E’ l’Indirizzo IP del server da utilizzare in caso di trasmissione con protocollo TCP PORT 20000 E’ la Porta IP del server da utilizzare in caso di trasmissione con protocollo TCP RETRY 3 E’ il numero massimo di tentativi per eseguire la connessione con il server Attenzione! Per un buon funzionamento i parametri utilizzati per la trasmissione con protocollo FTP devono essere vuoti. INSTUM_00518 Pag. 1/4 Rev. 02/04/2013 1.4 – Modifica del file config.ini per la trasmissione dei dati con protocollo FTP Per la trasmissione dei dati con protocollo FTP è necessario modificare i parametri specificati nella seguente tabella: Sezione [SERVER] Nome parametro PORT FTPSRVR FTPUSER FTPPWD RETRY Esempio 21 192.168.1.1 GPRSUser GPRS 3 Descrizione E’ la Porta IP del server FTP E’ l’Indirizzo IP del server FTP E’ il Nome utente da utilizzare per l’autenticazione al server FTP E’ la Password da utilizzare per l’autenticazione al server FTP E’ il numero massimo di tentativi per eseguire la connessione con il server FTP Attenzione! Per un buon funzionamento i parametri utilizzati per la trasmissione con protocollo TCP devono essere vuoti. 1.5 – Trasferimento del file config.ini dal PC al modem Per inviare il file config.ini dal PC al modem procedere come segue: 1. Seguire i punti da 1 a 4 della fase Scaricamento file config.ini dal modem al PC; 2. Scegliere il menu Telit Python; premere il collegamento ipertestuale Working folder, click to change, scegliere la cartella che contiene il file di configurazione modificato (ad esempio “c:\temp”); assicurarsi che nella casella bianca alla sinistra di R ci sia il carattere * (asterisco), se non fosse presente inserirlo e premere il bottone R alla sua destra, selezionare il file config.ini nella lista Files in PC folder, premere il pulsante [Upload selected file(s) from PC to module] e scegliere Sì per proseguire; il messaggio Done! avvisa che l’operazione è andata a buon fine; 3. Scegliere il menu Init, premere il pulsante [Close] e chiudere il programma rsterm. 2 - Installazione e collegamento modem Inserire la scheda SIM (abilitata alla trasmissione GPRS e richiesta codice pin disabilitato) nell’apposito vano del modem. Alloggiare il modem nella scatola dello strumento ed eseguire i collegamenti come indicato nel disegno accompagnatorio del datalogger in uso incluso nella scatola del modem. 3 - Configurazione strumenti E/R/M-Log La porta seriale 1 di E/R/M-Log deve essere configurata in base al tipo di collegamento e trasmissione dati scelto. La tabella seguente riporta i parametri da modificare per ciascun tipo supportato. Per maggiori informazioni sulla configurazione dello strumento fare riferimento al manuale SWUM_00286 del programma 3DOM. Velocità 9600 9600 9600 GSM e GPRS FTP alimentato da attuatore 9600 Tipo modem GSM GSM GPRS GPRS GPRS GPRS Alimentazione modem con attuatore No Sì No Sì No Sì Tipo di accensione modem - Spegne e riaccende in caso di blocco (consigliato) - Spegne e riaccende in caso di blocco (consigliato) - Spegne e riaccende in caso di blocco (consigliato) Tipo di protocollo GPRS - - FTP FTP TCP TCP - Impostare la rata desiderata Impostare la rata desiderata Impostare la rata desiderata Impostare la rata desiderata Parametro Rata di trasmissione spontanea GPRS GSM - GSM con alimentazione da attuatore GSM e GPRS FTP 9600 GSM e GPRS TCP alimentato da attuatore 9600 GSM e GPRS TCP Supporto tecnico LSI LASTEM Srl Per qualsiasi problema LSI LASTEM offre il proprio servizio di assistenza, contattabile via mail all’indirizzo [email protected] oppure compilando il modulo di Richiesta assistenza tecnica on-line raggiungibile dalla home page del sito internet www.lsi-lastem.it. Copyright 2008-2013 LSI LASTEM Srl. Tutti i diritti riservati. Le informazioni contenute nel presente manuale sono soggette a modifiche senza preavviso. Nessuna parte di questo manuale può essere riprodotta in qualsiasi forma o mezzo elettronico o meccanico, per alcun uso, senza il permesso scritto di LSI LASTEM. LSI LASTEM si riserva il diritto di intervenire sul prodotto, senza l’obbligo di aggiornare tempestivamente il manuale. INSTUM_00518 Pag. 2/4 Modem DEA718 Telit GT863-PY user’s Manual for E/R/M-Log datalogger Introduction This manual describes how to install and configure the DEA718 modem for using with E/R/M-Log datalogger. 1 – Modem configuration DEA718 modem is supplied from LSI LASTEM ready for working in GSM modality. For GPRS transmission through TCP or FTP it is necessary modify the config.ini file with rsterm terminal emulation software (available on MW6501 DVD in the folder Install\Support\RSTerminal). You can modify the file with a normal text editor (for example “Notepad” of Windows). 1.1 – Transfer the config.ini file from modem to PC To download the config.ini file from the modem to the PC, follow this procedure: 1. Start rsterm software, choose Init menu and select the serial port for modem connection. Set Baudrate to 115200 and Flowcontrol to Hardware and then click on [Open] button. 2. Connect modem to serial cable ELA105 and then (only then) power on the modem. It starts in command mode and it is ready to be configured. 3. From Init menu press [AT] button and wait for “OK” answer from the modem. 4. Make sure that the text of first lower button on the left is AT#SELINT=2; if it isn’t, set 2in the pull-down menu and click on the relative button; wait for “OK” answer from the modem. 5. Choose Telit Python menu; click on the [AT#LSCRIPT] button and wait for the display of the modem files (_crcfun.pyo, common.pyo, config.ini, etc …) in the Files in module list. 6. Press on Working folder, click to change hyperlink and choose the folder where configuration’s file will be saved (for example “c:\temp”);make sure that the character * (asterisk) is present in the white box at the left of R; if it is not present, insert it and then click the [R] button on its right; select config.ini file in Files in module list, click on [Download selected file(s) form module to PC] button and choose Yes in order to continue; the message Done! informs the user on positive result. 7. Choose Init menu, click on [Close] button and then close rsterm program. 1.2 – Modify the config.ini file for connection to GPRS network The following table relates SIM parameters that should be modified in config.ini file, in order to do the GPRS connection: Section [GPRS] Parameter name APN USER PASSWORD Example ibox.tim.it 1234567890 *) Description It is the Access Point Name to be used for GPRS connection It is the User name to be used for GPRS connection It is the Password to be used for GPRS connection Information on GPRS connection of main italian provider are contained in the following table: TIM Ibox.tim.it Telephone number *) APN User name Password VODAFONE internet Leave empty Leave empty WIND Internet.wind Leave empty Leave empty 1.3 – Modify the config.ini file for data transmission with TCP socket The following table relates parameters that should be modified in config.ini file, in order to do the socket TCP transmission: Section [SERVER] Parameter name IP PORT RETRY Example 192.168.1.1 20000 3 Description It is the Server IP address to be used for socket TCP transmission It is the Server IP Port to be used for socket TCP transmission It is the max number of attempts for connection with the server Attention! In order to have a good working, parameters used for transmission with FTP protocol must be empty (otherwise FTP transmission will be prevalent on socket TCP transmission). INSTUM_00518 Pag. 3/4 Rev. 02/04/2013 1.4 – Modify the config.ini file for data transmission with FTP protocol The following table relates parameters that should be modified in config.ini file, in order to do the data transmission with FTP protocol: Section [SERVER] Parameter name PORT FTPSRVR FTPUSER FTPPWD RETRY Example 21 192.168.1.1 GPRSUser GPRS 3 Description It is the Server IP Port of the FTP server It is the Server IP Address of the FTP sever It is the User name to be used for FTP server authentication It is the Password to be used for FTP server authentication It is the max number of attempts for connection with the FTP server In order to have a good working system, parameters used for transmission with socket TCP must be empty. 1.5 – Transfer the config.ini file from PC to the modem To send the config.ini file from PC to the modem, proceed as follows: 1. Follow steps 1 to 4 of Download the config.ini file from the modem to PC phase; 2. Choose the menu Telit Python; press the hyperlink Working folder, click to change, click the folder that contains the modified configuration file (for example “c:\temp”); make sure that in the white box at the left of R there is the character * (asterisk); if it isn’t, plug and press the R button to the right; select the config.ini file from the Files in PC folder list; press the [Upload selected file(s) from PC to module] button and click Yes to continue; the message Done! informs that the operation was successful; 3. Choose the Init menu, press the [Close] button and close rsterm software. 2 – Modem installation and connection Insert the SIM card (GPRS-enabled transmission and request pin code disabled) into the appropriate compartment of the modem. Place the modem in the box of datalogger and make the connections as shown in the datalogger drawing in use included in the box of the modem. For more information, you can see the chapter “Modem power supply” of datalogger manual. 3 – E/R/M-Log configuration Serial port 1 of E/R/M-Log must be configured in accord with the selected type of connection and data transmission. The following table shows the parameters to be modified for each supported type. For more information about the datalogger configuration, you can see SWUM_00286 manual (3DOM software). Parameter GSM GSM powered by actuator GSM and GPRS FTP GSM and GPRS FTP powered bya actuator GSM and GPRS TCP GSM and GPRS TCP powered by actuator Speed 9600 9600 9600 9600 9600 9600 Modem type GSM GSM GPRS GPRS GPRS GPRS Modem power supply with actuator No Yes No Yes No Yes Modem power up mode - Power down and re-power up in case of block (recommended) - Power down and re-power up in case of block (recommended) - Power down and re-power up in case of block (recommended) GPRS protocol type - - FTP FTP TCP TCP - Set the required rate Set the required rate Set the required rate Set the required rate GPRS automatic transmission rate - LSI LASTEM Srl technical support In case of problems contact the LSI LASTEM technical support at [email protected], or fill in the On-line technical support request form accessible from the home page of the website www.lsi-lastem.it. Copyright 2008-2013 LSI LASTEM. All rights reserved. This manual can be modified without notice. Anybody can copy, print or publish this manual without LSI LASTEM written authorization. LSI LASTEM reserves the right to modify the product without an immediate revision of this document. INSTUM_00518 Pag. 4/4