dati tecnici - technical data caratteristiche prodotto
Transcript
dati tecnici - technical data caratteristiche prodotto
Via Trieste 1, 33048 San Giovanni al Natisone, Udine, Italia Tel. +39 0432 747911 - Fax +39 0432 758444 www.friulsider.com - [email protected] Assistenza tec. per Italia: Tel. 0432 747906 SCHEDA TECNICA - TECHNICAL SHEET VCN Vite connettore TC portante per legno ad uso professionale - interamente filettata Rev: 00 Pag. 1/1 Cylindrical head load bearing connection fixing for professional use - fully threaded DATI TECNICI - TECHNICAL DATA vite / screw dxL d1 [mm] 8x160 8x200 8x240 8x280 8x300 8x360 8x400 10x120 10x160 10x200 10x240 10x320 10x400 10x480 10x600 Inserto / Bit Torx P [mm] S [mm] K [mm] Ø 5,2 T-40 4,8 Ø11 6 Ø 6,2 T-50 5,6 Ø13 7 Cod. 07313b08160 07313b08200 07313b08240 07313b08280 07313b08300 07313b08350 07313b08400 07313b10120 07313b10160 07313b10200 07313b10240 07313b10320 07313b10400 07313b10500 07313b10600 CARATTERISTICHE PRODOTTO - PRODUCT FEATURES Tipo / Type Materiale / Material Rivestimento / Coating Vite acciaio cementato (cl.9.8 ~*) zincatura bianca 8µm ISO4042 Screw cemented steel (gr.9.8 ~*) white zinc plated 8µm ISO4042 *Caratteristiche meccaniche secondo tabella sotto / For mechanical characteristics, see table below. Caratteristiche meccaniche vite a rottura - Mechanical screw failure characteristics Vite Screw AREA RESISTENTE SECTION [mm²] TRAZIONE TENSILE [kN] TAGLIO PURO SHEAR LOAD [kN] TORSIONE TORQUE [Nm] MOMENTO FLETTENTE BENDING MOMENT [Nm] Ø8 21,5 20 12 25 20 Ø10 30,5 28 15 40 30 FLESSIONE FLEXION > 60° INSTALLAZIONE - INSTALLATION Vite Screw Inserto / Bit Torx Coppia max. serraggio Max screwing torque [Nm] Avvitatore Max drilling speed giri-min / r.p.m Ø8 T-40 20 600 30 600 Ø10 T-50 NOTE: non è necessario il preforo. / NOTE: pilot hole is not required. CARICHI DI TRAZIONE AMMISSIBILI (1) - PULL OUT RECOMMENDED LOADS (1) Legno di abete da costruzione (2) - Construction fir wood structures (2) Diametro vite Ø8 Ø10 Screw diameter Profondità inserimento [mm] 100 140 100 Embedment depth Trazione ammissibile 3,0 4,5 3,5 N [kN] Tensile recommended load 1kN = 100 kgf (1) I carichi ammissibili derivano dai carichi caratteristici di rottura e sono comprensivi del coefficiente di sicurezza totale =3. The recommended loads derive from the characteristic failure loads and are inclusive of the total safety factor =3. (2) 3 Massa volumica media ~450 kg/m e umidità ~15% (direzione ortogonale alla fibra). 3 Average density ~450 kg/m and humidity ~15% (direction at right angle to fibre). 140 5,0 I carichi consigliati derivano da prove eseguite presso il laboratorio Friulsider nel rispetto delle norme di riferimento. I valori di carico riportati hanno valore solo se l'installazione è stata eseguita correttamente. Il progettista è responsabile del dimensionamento e del numero dei fissaggi. The recommended loads derive from tests carried out in the Friulsider laboratory in accordance with the appropriate standards. The load values are only valid if the installation has been carried out correctly. The design engineer is responsible for the designing and calculation of the fixing. Friulsider S.p.A si riserva il diritto di apportare modifiche senza preavviso / Friulsider reserves the right to make modifications without prior notice.